Zephyr Willow AK8800AG Use And Installation Manual
Zephyr corporation willow use, care, and installation guide
Hide thumbs
Also See for Willow AK8800AG:
- Use and installation manual (17 pages) ,
- Use, care and installation manual (18 pages)
Table of Contents
Related Manuals for Zephyr Willow AK8800AG
Summary of Contents for Zephyr Willow AK8800AG
- Page 1 Willow AK8800AS AK8800AG INTENDED FOR OUTDOOR COVERED PATIO OR LANAI AREA. Model number: Serial Number: Date of Purchase: Sales Dealer: AUG08.0101 © 2008 Zephyr Corporation READ AND SAVE THESE INSTRUCTIONS...
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE LIST OF MATERIALS INSTALLATION Ducting Calculation Sheet Mounting Height & Clearance Ducting Options Specifi cations Electrical Installing the Power Pack CONTROLS Rocker Switch Controls MAINTENANCE Cleaning and Installing Filters Lights TROUBLESHOOTING LIST OF PARTS AND ACCESSORIES...
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
-
Page 5: Operation
CAUTION To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. OPERATION Always leave safety grilles and fi lters in place. Without these components, operating blowers could catch onto hair, fi ngers and loose clothing. -
Page 6: Parts Supplied
www.zephyronline.com MODELS: AK8800AS AND AK8800AG PARTS SUPPLIED 1 - 316S High quality stainless steel Power Pack (AK8800AS) 1 - Gray powder coated Power Pack (AK8800AG) 2 - Baffl e fi lters 2 - Halogen light bulbs (pre-installed) 1 - Dual internal blower (pre-installed) 1 - 8”... - Page 7 Equivalent number Duct pieces length x used 3-1/ 4” x 10” 1 Ft. Rect., straight 6” Round, 1 Ft. straight 7”-10” Round, 1 Ft. straight 3-1/ 4” x 10” 15 Ft. Rect.90 elbow 3-1/ 4” x 10” 9 Ft. Rect.45 elbow 3-1/ 4”...
- Page 8 Min 30" - Max 36" 36" DUCTING A minimum of 8” round ducting must be used to maintain maximum air fl ow effi ciency. Always use rigid type metal ducts only. Flexible ducts could restrict air fl ow by up to 50%. Also use calculation (on page 5) to compute total available duct run when using elbows, transitions and caps.
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver Tape or Duct Tape. Some Ducting Options side wall cap w/ gravity damper...
- Page 10 316 High Class Stainless Steel Body for AK8800AS ” 7/16 elec. ” ” 11/16 ” ” 13/16 ” ” 5/16 ” ” ” 5” ” ” 15/16 ” 13/16 front www.zephyronline.com ” 7/16 ” elec ” 13/16” ” ” 11/16 ”...
- Page 11 ELECTRICAL WARNING All Electrical work must be performed by qualifi ed electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances.
- Page 12 CAUTION: At least two installers are required due to the weight and size of the hood. Remove support screw from top of Power Pack before installing into cabinet. FIG 2b 1. Place 8” round adapter on top of power pack and secure with (4) M4x8 screws.
- Page 13 Adjust Blower Level (2 Speeds) Light On/Off By pressing , the light is switched On and Off. Blower Speed Selection The 2 speed levels are selected by switching to Switching the rocker switch to middle Lights On/Off is on, is off. for level one and for level two.
-
Page 14: Surface Maintenance
CAUTION: If this hood is installed in a salt water area (example: coast), rinse all surfaces once a week with clear water (even if the hood is not used), and wipe dry completely. SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/ scoring pads which will scratch and damage surface. -
Page 15: Replacing Light Bulbs
Replacement bulbs are available at specialty lighting stores. Purchase type MR16 (GU-10) 35W halogen. For Zephyr part numbers please turn to page 15 of the manual. Bottom View... - Page 16 TROUBLESHOOTING PROCEDURES FOR WILLOW Issue Cause After installation, 1. The power source is not turned ON. the unit doesn’t work. 2. The power line and the cable locking connector is not connecting properly. 3. The switch board and control board wirings are disconnected.
- Page 17 DESCRIPTION Replacement Parts Light Bulb MR16 (GU10) 35W (each) Baffl e Filter (each) Optional Accessories Liner, 36” Liner, 42” Liner, 48” Liner, 54” Liner, 60” To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368 PART # Z0B-0023 50210010 AK0886AS...