Subscribe to Our Youtube Channel
Related Manuals for Metos Master AQUA 50
Summary of Contents for Metos Master AQUA 50
- Page 1 DISHWASHER ELECTROMECHANICAL SWITCHES LOWER AND UPPER WASHING TYPE: Metos Master AQUA 50 Accessories DETERGENT DISPENSER DRAIN PUMP Installation and Operation Manual S/N: Rev.: 1.1...
- Page 2 Thank you for choosing our appliance. The installation, use and maintenance instructions given in this manual have been pre- pared to ensure the long life and correct operation of your appliance. Follow these instructions carefully. We have designed and manufactured this appliance according to the latest technological developments.
-
Page 3: Table Of Contents
TRANSLATION OF THE ORIGINAL INSTRUCTIONS SUMMARY Page IMPORTANT INFORMATION INSTALLER SECTION 1. MACHINE INSTALLATION 1.1 Receipt of the appliance 1.2 Water connection 1.3 Electrical connection 1.4 Temperature adjustment 1.5 Rinse aid dispenser operation 2. DETERGENT DISPENSER INSTALLATION 2.1 Electrical connection 2.2 Water connection 2.3 Dispensing the detergent 3. -
Page 4: Important Information
INSTRUCTIONS This instruction booklet must be kept with the dishwasher for future consultation. If the dishwasher is sold or transferred to another user, make sure the booklet always goes with the appliance so that the new owner can have the necessary information on operation and the relative instructions. - Page 5 · Do not use water to put out fires on electrical parts. · Do not clog the intake or dissipation grids. · Only qualified personnel can access the control panel after power is switched off. · The machine has an IPX3 rating of protection against accidental splashes of water. It is not protected against pressurized jets of water, so it is recommended that pressure cleaning systems not be used.
-
Page 7: Installer Section
INSTALLER SECTION ATTENTION: At the end of installation make sure to remove the parts of this booklet relevant to the in- staller, for future consultation. 1. MACHINE INSTALLATION Min. Max. O supply temperature table Pressure Table Machine upon Standard Macchine request from catalogue Static Pressure... -
Page 8: Temperature Adjustment
INSTALLER SECTION Temperature adjustment If necessary, the water temperature of the wash and rinse cycles can be adjusted by means of the fine-adjustment screws on the respective thermostats. The recommended temperatures are 55° C for the wash cycle (tub) and 85 - 90° C for the rinse cycle (boiler). - Page 9 INSTALLER SECTION THE DISPENSERS ARE PRE-SET TO A 5 CM INTAKE OF PRODUCT FOLLOWING A TEST PHASE SYSTEM CHECK. THIS MEASUREMENT SHOULD BE ADJUSTED ACCORDING TO THE TYPE OF RINSE AID USED AND WATER HARDNESS. 10805 10805 10805 10805 10807 10807 10806 10806...
-
Page 10: Detergent Dispenser Installation
INSTALLER SECTION 2. DETERGENT DISPENSER INSTALLATION Point B min 3 15108/E 15108/E pict. 9 15185 pict. 10 CONNECTION DIAGRAM Electrical connection • Follow the wiring diagram attached to the machine. Water connection a) A Ø12 hole must be made on the back of the appliance. In some appliances the hole has already been made and is closed with a plastic cap. -
Page 11: Pump Technical Data And Information
INSTALLER SECTION 3. TECHNICAL DATA AND USEFUL INFORMATION ON PUMPS Emptying pump (optional) How installing, pay particular attention to the position of the emptying tube (see pict. 7). See chapter 5.3. for operations description. pict. 7 CAUTION: INCORRECT POSITIONING OF THE TUBE. CAUTION: CORRECT POSI- TIONING OF THE TUBE Pressure increasing pump (optional) -
Page 12: Dataplate
INSTALLER SECTION Dataplate CL/Part Code DW 999XXYYYY Model DESCRIPTION S/N DW A 1015770 Type ..400V 3N 50HZ 500W 3500W TECHICAL SPECIFICATION IPX3 Pressione Dinamica alimentazione idrica 200-500 kPa Pression dynamique arriveè d'eau Dynamic pressure water supply Dynamischer Druck asserreinlauf MADE IN ITALY Pressione dinamica vapore saturo Temperatura massima acqua in ingresso 60°C... -
Page 13: User Section
USER SECTION 4. CONTROL PANEL AND RELATIVE SYMBOLS CONTROLS INDICATORS Main switch 0-1 Power on indicator Tub full indicator Cycle START button Supplementary cold rinse Washing cycle button indicator Regeneration cycle Regeneration START indicator button (optional) Manual empty button Temperature (optional) indicator Wash type selector... -
Page 14: Use Of Detergent
USER SECTION Use of detergent ONLY use NON FOAMING types suitable for industrial glass-washers and dishwashers. It is advisable to use liquid detergents. Put the detergent directly in the tub. The correct amount will be suggested by the product manufacturer according to the water hardness. -
Page 15: Regeneration Device (Optional)
USER SECTION Regeneration device (optional) Resin regeneration by the water softener is very important. Resin regeneration: resin rege- neration should be carried out according to the number of cycles as indicated in the picture below. Ex. 27°f (or 15°D)= 39 cycles. To carry out the purifying cycle, follow these instructions: •... -
Page 16: Maintenance
USER SECTION 6. MAINTENANCE Regular Maintenance WARNING: The machine is not protected against water jets, therefore do not use pressure cleaning systems. Contact your cleaning products retailer for detailed instructions on the methods and products to use for periodic sanitizing of your appliance. DO NOT use bleach or chlorine-based detergents for cleaning the ap- pliance. -
Page 17: Environmental Features
USER SECTION 8. ENVIRONMENTAL FEATURES Packing The packing consists of the following: • a wood pallet; • a nylon bag (LDPE); • multi-layered cardboard; • polyurethane foam (PS); • polypropylene support (PP). We kindly advise you to dispose of the above-mentioned material in accordance with current environmental regulations. -
Page 18: Troubleshooting
USER SECTION 10. TROUBLESHOOTING Type of Problem Possible Causes Cure The appliance does not start The main switch is turned off Turn on the switch The appliance does not The water tap is closed Open the water tap draw water The rinsing arm nozzles or the Clean the rinsing arm nozzles, the pipes and the electrovalve electrovalve filter are clogged and/or... - Page 20 KROMO S.R.L. - VIA MESTRE, 3 - 31033 CASTELFRANCO VENETO (TV) ITALY - TEL. ++39-423-734580 - FAX ++39-423-734581 KONFORMITÄTSERKLÄRUNG CE DICHIARAZIONE DI CONFORMITA' CE DECLARACION DE CONFORMIDAD CE DECLARATION OF CONFORMITY CE DECLARAÇAO DE CONFORMIDADE CE DECLARATION DE CONFORMITE CE Il sottoscritto, legale rappresentante della azienda sopra indicata, dichiara che l'apparecchiatura: The undersigned, officer of the above-written company, hereby declares that the machine: Le soussigné, représentant légal désigné, déclare que l'appareil:...
Need help?
Do you have a question about the Master AQUA 50 and is the answer not in the manual?
Questions and answers