Subscribe to Our Youtube Channel
Related Manuals for Metos LUX 60 EL
Summary of Contents for Metos LUX 60 EL
- Page 1 DISHWASHER LUX 60 EL Installation and User Manual COD.: 4400_U Ed. 02 - 03/2012 4246028, 4246029, 4246030, 4246031...
- Page 2 Thank you for choosing our machine. The instructions for installation, maintenance and use found on the following pages have been prepared to ensure a long life and perfect operation of your unit. Please, do follow the instructions carefully. We have designed and built this machine using the latest innovative technologies. Now you shall take good care of it.
-
Page 3: Table Of Contents
TRANSLATION OF THE ORIGINAL INSTRUCTION CONTENTS Page WARNINGS 1. MACHINE DESCRIPTION 1.1 Machine Description 1.2 Machine features 2. OPERATION 2.1 Control panel and relative symbols 2.2 Machine start-up 2.2.1 Start-up 2.2.2 Operation 2.2.3 Switching OFF 2.3 Detergent use 2.4 Rinse aid use 2.5 Drain pump system 2.6 Regeneration function (optional) 2.7 Additional Cooling Function (Optional) -
Page 5: Warnings
WARNINGS This instruction booklet must be kept with the machine for future consultation. If this machine is sold or transferred to other users, make sure the booklet always goes with the unit so that the new owner can have all the necessary information on operations and all relevant instructions. -
Page 6: Machine Description
1. MACHINE DESCRIPTION Machine Description Control panel Wall-hung main power switch: at installation serviceman supply and Door care, according to local laws Control panel Control panel Door Door Standard equipment for machine with a 50mm rack: nr. 1 glasses rack nr. 1 plates rack 500x500mm Capacity per plate rack: 12 soup plates or 18 flat plates... - Page 7 Option D) Other standard equipment for machine with a 50mm rack: C) nr. 1 square trays rack 500x500mm D) nr. 1 trays support 6 pcs nr. 1 inox spatulas rack Option C) Standard equipment for machine with a Option B) 40mm rack: option A) nr. 2 square glasses racks 400x400mm option B) nr. 2 round racks Ø 400mm Standard equipment for machine with...
-
Page 8: Machine Features
To operate the machine, 3 connections are needed: • Electrical; • Water supply; • Water drain. This is a cycle machine comprising a 55°C wash cycle with detergent, a 82°C rinse cycle with injection of rinse-aid in the boiler hull. This machine is designed exclusively for washing dishes, glasses and various pots and pans with human food type of residue. -
Page 9: Operation
2. OPERATION 2.1 Control panel and relative symbols pict. 1 A) Cycle light indicator B) Selected cycle indicator C) Tank temperatur display D) B oiler temperature display E) ON / OFF indicator F) Regeneration indicator G) Drain indicator H) S TART push-button to start up cycle / select cycle I) Cool extra indicator J) Switching – On / STAND BY button K) R egeneration push-button (optional) L) Drain push-button (optional) 2.2 Machine start-up... -
Page 10: Operation
2.2.2 Operation • Insert the rack filled with dishes to wash. The plates must be correctly placed in the rack (see pict. 3). Close the door. • Select the wanted washing cycle (1, 2, 3, ∞) by pushing the button "H" (see pict. 1). The display will show in sequence all available programs. Once the wanted program is displayed, do release the button. The green LED "B" of the selected cycle lights up (1, 2, 3, ∞). pict. 3 • Start the cycle by pushing the button "H" for not more than 1sec (see pict. 1). Starting of the cycle is signalled by the indicator of the selected cycle flashing. At the end of the cycle the indicator stops flashing and the message "END" appears on the display. • The machine is ready for a new wash. -
Page 11: Detergent Use
Detergent use The detergent shall be the NO FOAM type, suitable for industrial dishwashers, and must comply with the EN 60335-2-58/A11 norms. The use of good quality liquid detergents is recommended. The detergent must be introduced in the tank. The amount is recommended by the manu- facturers according to the water hardness. By request the dishwasher can be equipped with an electric detergent dispenser (always recommended). 1cm. of the product drawn into the tube is equal to about 0.15 g. A correct amount of deter- gent is very important for a successful wash. Should the detergent lack, the display will show "NO DE"... -
Page 12: Regeneration Function (Optional)
Regeneration function (optional) Regeneration is carried out after the fl ashing signal of the regeneration key indicator "F". IMPORTANT: Before starting a regeneration cycle check if there is salt in the special container (max 0,500kg). Fill the special salt container with tank empty and machine off. When displaying "NO SA" (alternated to the tank and boiler temperatures and with machi- ne on stand-by mode) add salt in the container in the wash-tank (only with optional water softener). Rinse the tank immediately if salt is spilled in it. To start the regeneration cycle, switch the machine off with the key "J". The red LED lights up. -
Page 13: Additional Cooling Function (Optional)
Additional Cooling Function (Optional) This function can only be enabled if the machine is installed with the optional "Additional Cooling" function. Machine ON. Press the button "K" for at least 3 sec. After the hot rinse is completed, an additional fresh-water rinse can be made. During the wash cycle or manual draining the type of rinse selected cannot be changed. The Additional Cooling selection is displayed with the decimal point of the second display lighting up. -
Page 14: Warnings
WARNINGS: • Do not slam the door when opening and closing. • Do not put material or objects on the machine. • The machine has an IPX3 protection rating against accidental water splashes and is not protected against pressurized water jets. Pressure-cleaning systems shall, therefore, not be used on this machine. • Do not dip bare hands into water containing detergent. If this should occur, wash them immediately with plenty of water. Check the safety instructions on the detergent container. -
Page 15: Ecological Aspects
3. ECOLOGICAL ASPECTS Recommendations for optimal use of energy, water and additives Salt dosing A pre-set (by the manufacturer) quantity of salt is injected in the resins at each regeneration cycle. It is important to observe the number of regeneration cycles recommended in para- graph 2.6 "Regeneration device" in order to avoid salt spills or lime deposits. Use the machine fully loaded when possible. This shall prevent detergent, rinse aid, water and energy consumption waste. Detergent and rinse-aids Use detergents and rinse-aid chemicals with high biodegradability, to best respect the en- vironment. -
Page 16: Maintenance
5. MAINTENANCE Routine maintenance WARNING: The machine is not protected against pressurized water jets. Do not use pressure cleaning system against the machine. It is recommended to contact the seller of chemicals for proper cleaning instructions, in order to have detailed indications on methods and products for the correct periodical machine sanitation. -
Page 17: Machine Installation
6. MACHINE INSTALLATION Handling 6.1.1 Handling the product The machines must be handled strictly as shown in pict. 5 regarding the grip points indicated for lifting with a lift truck. Latch the machine in a way that secures no vibration or shocks during transportation. N.B.: Slinging with ropes not recommended. After unpacking, make sure the appliance has not been damaged due to transportation. If it has been, do notify the seller about this problem. If the damage might question the machine’s safety, do not install the appliance. See chapter 8 for disposal of the packing material. pict. 5 6.1.2 Storage Storage temperature: min. +4°C - max +50°C - humidity <90%. The stored parts should be checked periodically, to detect any sign of deterioration. -
Page 18: Water Supply Connection - Characteristics
A suitable omni-polar, one-way switch shall be installed and sized according to the absorption provided, with a contact opening of at least 3 mm. This switch shall be solely and exclusively used for this purpose and installed in the immediate vicinity of the machine, installed in full respect of the local laws. Always turn the machine off via this switch. This is the only model of switch that guarantees a total electrical power disconnection. 6.2.3 Water supply connection - Characteristics Fresh water supply features: Water characteristics table... -
Page 19: Electrical Connection
6.3.2 Electrical connection The electrical connection shall be carried out in accordance to the local laws in force. The machine has a connection at the back, indicated by the symbol , that is meant to link the steel structure and masses among different apparatuses, to prevent electro-static electrical shocks. -
Page 20: Signals And Alarms
7. SIGNALS AND ALARMS The alarms and the signals messages are visualized, based upon their meaning . When on the display the LED "F" key flashes, a total regeneration is needed above the "K" (only with optional water softener). When flashing "NO DE" (alternated to the tank and boiler temperatures and with machine on stand-by mode), add detergent in the detergent tank (only with optional "Sensor for Chemicals Low Level"). When flashing "NO RI" (alternated to the tank and boiler temperatures and with machine on stand-by mode) add rinse-aid chemical in the rinse-aid tank (only with optional "Sensor for Chemicals Low Level"). When displaying "NO SA" (alternated to the tank and boiler temperatures and with machi- ne on stand-by mode) add salt in the container in the wash-tank (only with optional water softener). When displaying "DOOR"... -
Page 21: Environmental Aspects
8. ENVIRONMENTAL ASPECTS Packaging Packaging is made of the following components: • a wooden pallet; • a nylon sack (LDPE); • a multi-layer carton; • polystyrene (PS) strips; • polypropylene (PP) banding. All above materials, shall be disposed and treated in accordance with the Local Laws in force. Disposal The symbol WEEE/RAEE used on this product indicates that it cannot be treated as domestic waste. Proper disposal of this product contributes to protecting the environment. For more information on product recycling, contact the local authorities, domestic waste authorities or the dealer where the product was purchased. For product or parts disposal, follow the Council directives 2002/95/EC and 2002/96/EC as amended and/or application legislative decrees. -
Page 22: Troubleshooting
9. TROUBLESHOOTING Type of Problem Possible Causes Cure Main switch not ON. The machine does not turn Turn switch ON. The machine does not load Water valve shut. Open the hot and/or cold water valve. Rinse area nozzles or solenoid-valve Clean the rinse arm nozzles, piping and solenoid-valve filter. water. filter blocked and/or scaled with Check that the water hardness is <10°f. limestone. Replace pressure-switch. Defective pressure-switch. Scarce water supply pressure The water drains very slowly Check the water supply pressure...
Need help?
Do you have a question about the LUX 60 EL and is the answer not in the manual?
Questions and answers