Wireless Communication - Wireless+/Deluxe - Nilfisk-Advance Supreme 100 Instructions For Use Manual

12 Wireless communication - Wireless+/Deluxe

WARNING!
Do not pull out the suction hose from the cleaner
while the motor/fan unit of the cleaner is running.
These machines have a safety shut off function.
This shut off function will be activated when the ma-
chine is operated with a closed vacuum socket.
12.1 Transceiver box
Before you mount the transceiver box to the
wall you should always test if you have a
signal between the transceiver box and the
hose handle in your entire home. Connect
the box to the cleaner and turn the cleaner
on and off using the hose handle from differ-
ent places in your home.
The fi rst transmission
The hose handle and the cleaner needs to have a fi rst com-
munication before starting the cleaner. This is also valid if the
hose handle has been replaced (spare part) or if you want to
connect an extra hose. Do like this before starting your wire-
less cleaner:
Unplug the main cord.
1)
2) Plug in the cord again, and then push the on/off button
at the hose handle for approximately 10 seconds. This
must be done within 60 seconds after the cleaner has
been plugged in
3) The handle and the cleaner do now communicate.
Installing the transceiver box
Mount the transceiver box on the wall minimum 1 meter
away from the cleaner for best signal between the trans-
ceiver box and the hose handle. The transceiver box can be
moved to different places in your home for a better range by
using an up to 30 meter network cable. Cables can often be
bought in your local Electronics store.
Connecting the transceiver box
To be able to use the wireless Nilfi sk hose handles, you must
fi rst connect the transceiver box to the cleaner. This is done
by using the 2 meter the network cable (RJ45) that comes
with the transceiver box. Connect the cable to the transceiver
box and the right socket in the back of the cleaner.
12.2 Wireless hose handle
Instruction for use
The on-off function and power regulation is controlled by radio
technology. You do not have to point at the machine like infra-
red controls. The wireless bent end can be used anywhere in
the house.
Start and stop
Start: One push at the switch will start the cleaner.
Stop: One push at the switch will shut off the cleaner.
The power regulation can be adjusted in 5 steps. You switch
between the different steps by pressing the (+) or (-) buttons
at the hose handle.
Wireless
The LED-indicator is placed above the on/off button and will
be activated with different lights depending on the actions
that are taken:
50
The lamp is activated at start or stop actions or when the
power regulation is adjusted.
The lamp fl ashes a warning light that indicates that the bag
fi lter/dust bag is clogged and needs cleaning/replacement.
You must then check and clean or replace the fi lter/bag.
Deluxe info center display
The display is placed above the on/off button and will show
different symbols depending of the status of the cleaner.
Signal
strength
Bag/fi lter
Speed
Speed level: Bars shows the actual speed level
Low Battery fl ashing: Battery is under 5%, Change battery.
Service warning / Air fl ow blocked lit: Indicates for both
Service warning and Blocked airfl ow. See 10 Troubleshooting
Check bag/fi lter fl ashing: It is almost time to change dust
bag and clean fi lter.
Check bag/fi lter lit: Dust bag or fi lter is clogged. Change
dust bag and clean fi lter.
Signal fl ashing: Hose handle is out of range. No connec-
tion to the cleaner.
Overheat fl ashing: Thermal cut-out has tripped and the
cleaner has stopped. See 10 Troubleshooting
Battery
The lifetime of the enclosed batteries in the bent end is ap-
proximately three (3) years. If the battery capacity at opera-
tion start is to low, the cleaner will then be shut off. If the
cleaner would not start or the power regulation via the hose
handle does not work, you must replace the batteries at the
hose handle. Replace to battery type 1.5V AAA. For more in-
formation and trouble shooting see chapter 10 in this instruc-
tion for use.
How to replace battery at the
hose handle
1) Open the lid of the battery holder
by sliding the lid towards the front
of the hose handle.
2) Replace the used batteries with
two new ones, type 1.5V AAA.
Make sure the polarity of the
batteries is placed correct at the
bracket.
3) Slide the battery lid back until you
hear a click.
Power
Power
regulation -
regulation +
On/Off
LED-
indicator
Overheat
Low battery
Service