Filter And Dust Bags - Supreme 150 / Performer 150 / Supreme 250 / Performer 250 / Supreme Lcd; Replacing The Bag Fi Lter; Fitting The Bag Fi Lter; Replacing The Dust Bag - Nilfisk-Advance Supreme 100 Instructions For Use Manual

7 Filter and dust bags - Supreme 150 / Performer 150 / Supreme 250 /
Performer 250 / Supreme LCD
7.1 Replacing the bag fi lter
A bag fi lter must always be installed in the dust container.
Clean the fi lter in the following way:
1. Release the two handles clamping the dust container. The
handles are easily unlocked by lifting up the handles until
they come to a stop. When you pull the handles outwards
away from the cleaner, the container is released. Fig. 22.
2. Do not remove the fi lter from the container. Instead, give the
fi lter a light shaking inside the container to loosen dust from
the fi lter allowing it to fall into the container. This is done by
grasping the strap on the fi lter and quickly move the fi lter up
and down as shown in Fig. 23.
3. Lift out the bag fi lter. If a dust bag is being used - remove the
dust bag. Then empty the container of any remaining dust in
a suitable place.

7.3 Replacing the dust bag

The machine is supplied with a dust bag. Replace the dust bag
in the following way:
1. Release the two handles clamped on to the dust container.
The handles are easily unlocked by lifting up the handles un-
til they come to a stop. When you pull the handles outwards
away from the cleaner, the container is released. Fig. 22.
2. Lift off the container.
3. Shake the dust from the bag fi lter. It may be advantageous
for the fi lter to be installed in the container in such a way that
dust in the fi lter can be shaken down into the dust container.
4. Lift out the bag fi lter.
5. Remove the dust bag by taking hold of the cardboard
stiffener and carefully pulling out the card and bag from the
container, Fig. 24. Fold down the perforated part of the card-
board towards the opening of the bag in order to prevent the
bag contents to leak out.
6. Empty the container of dust.
44
Fig. 22
7.2 Fitting the bag fi lter
Replace the bag fi lter in the machine as follows:
1. Replace the cleaned/shaken bag fi lter in the container. Make
sure the fi lter support fi ts into the inner edge of the dust
container properly. Check that the fi lter is fi tted the right way
up - the cloth handle on the fi lter should be visible.
2. Then replace the dust container with the bag fi lter in the
cleaner's vacuum unit.
3. Attach the container on the vacuum unit by lifting the con-
tainer back in place and pushing the handles back in over
the edge of the cleaner till you hear a click. Push down the
handles and ensure that the vacuum unit and dust container
are fi tted together properly.
Fig. 24

7.4 Fitting the dust bag

Replace the dust bag as follows:
1. Fit the dust bag's card with a hole into the bag holder, Fig. 25.
2. Replace the cleaned/shaken bag fi lter in the container. Make
sure the fi lter support fi ts into the inner edge of the dust
container properly.
Check that the fi lter is fi tted the right way up - the cloth han-
dle on the fi lter should be visible.
3. Replace the dust container on the vacuum unit. Close the
container on the vacuum unit by applying inward pressure to
the two handles to ensure the vacuum unit and dust con-
tainer are fi tted together properly.
The Supreme 150 / Performer 150 / Supreme 250 /
Performer 250 / Supreme LCD can be run with or without
the installation of a dust bag - the choice is yours. These
products must though always be operated with the bag
fi lter fi tted in the cleaner.
Fig. 23
Fig. 25