1. Manuals
  2. Brands
  3. Qvis Manuals
  4. Security Camera
  5. AMB-VANIR
  6. User manual

Qvis AMB-VANIR User Manual

1.3 & 2 mega pixel vandal dome ip cameras
Hide thumbs
Table of Contents

Advertisement

Quick Links

AMB-VANIR
AMB-VANIR-2
AMB-VANIRM2
1.3 & 2 MEGA PIXEL VANDAL DOME IP CAMERAS
User's Manual
V2.0 06 / 2014

Advertisement

Table of Contents
loading

Related Manuals for Qvis AMB-VANIR

Summary of Contents for Qvis AMB-VANIR

  • Page 1 AMB-VANIR AMB-VANIR-2 AMB-VANIRM2 1.3 & 2 MEGA PIXEL VANDAL DOME IP CAMERAS User’s Manual V2.0 06 / 2014...
  • Page 3 Welcome Thank you for purchasing the Vandal Dome IR LED IP Camera. This user’s manual is designed to be a reference tool for the installation and operation of your system. Here you can find information about the corresponding IP camera’s features and functions, as well as a detailed installation method.
  • Page 4 Important Safeguards and Warnings 1．Electrical safety  All installation and operation here should conform to your local electrical safety codes.  The power supply shall conform to the requirement in the SELV (Safety Extra Low Voltage) and must make sure that the limited power source is rated 12V DC or 24V AC. Please note: Do not connect two power supplying sources to the device at the same time;...
  • Page 5  Please make sure the CCD (CMOS) component is away from the radiation of the laser beam device. Otherwise it may result in CCD (CMOS) optical component damage.  It is recommended that the grounding studs of the product should be grounded, so to further enhance the reliability of the camera.

  • Page 6: Table Of Contents

    Table of Contents General Introduction ..................... 1 Overview ......................1 Features ......................1 Specifications ....................2 1.3.1 Performance ....................2 Structure ........................5 Dimensions ....................... 5 Port Description....................6 Bidirectional talk ....................9 2.3.1 Device-end to PC-end................. 9 2.3.2 PC-end to the Device-end ................9 Alarm Setup ....................

  • Page 7: General Introduction

    Network  Supports a maximum of 20 connections. Monitor  Adopts the following audio and video transmission protocols: HTTP, TCP, UDP, MULTICAST, RTP/RTCP, RTSP, etc.  Supports web access. © Copyright Qvis ®. All documentation rights reserved.

  • Page 8: Specifications

    Support real-time network monitor, local record, and remote operation Resources at the same time. User Interface Remote operation interface such as WEB, PSS. System Status Bit stream statistics, log, and software version. © Copyright Qvis ®. All documentation rights reserved.
  • Page 9 MPEG: 32K – 12288Kbps (adjustable) Video Bit Rate Video Flip Supports Mirror and Flip functions Snapshot Max 1f/s snapshot. File extension name is JPEG. Privacy Mask Supports max 4 privacy mask zones © Copyright Qvis ®. All documentation rights reserved.
  • Page 10 AC24V, DC12V and PoE (AC 24V port is inside the device.) Power 5W MAX 7W MAX Consumption Working C~+60 Temperature Protection Level IP66 Working ≤ 90% Humidify Φ 151mm * 119mm Dimensions(mm) Weight 1.25Kg Installation Installation with the bracket. © Copyright Qvis ®. All documentation rights reserved.

  • Page 11: Structure

    You can refer to the following figures for dimension information. The Unit is mm (see Figure 2- 1 & Figure 2- 2 Figure 2- 1 Dimension illustration 1 Figure 2- 2 Dimension illustration 2 © Copyright Qvis ®. All documentation rights reserved.

  • Page 12: Port Description

    2.2 Port Description The ports are shown in Figure 2 – 3 and Figure 2 – 4 (AMB-VANIR & AMB-VANIR2 cameras only). Figure 2 - 3 Port 1 Figure 2 - 4 Port 2 © Copyright Qvis ®. All documentation rights reserved.
  • Page 13 The ports are shown in Figure 2 – 3 and Figure 2 – 4 (AMB-VANIRM2 camera only). Figure 2 - 5 Port 2 Figure 2 - 6 Port 1 © Copyright Qvis ®. All documentation rights reserved.
  • Page 14 Output audio signal to devices such as loud AUDIO_OUT speaker. Ground end. Output analog video signal. It can connect VIDEO_OUT to TV monitor to view video. © Copyright Qvis ®. All documentation rights reserved.

  • Page 15: Bidirectional Talk

    Note: Please go to the Master Volume interface of the PC to set it first if you want to use the dual-way bidirectional talk. Please select Front MIC mode in the record control interface. (You can select microphone enhanced in ‘Advanced’ interface if the audio is too low.) © Copyright Qvis ®. All documentation rights reserved.

  • Page 16: Alarm Setup

    When the input signal is connected to the 3.3V or is idle, the device collects the logic ‘1’. When the input signal is grounded, the device collects the logic ‘0’. © Copyright Qvis ®. All documentation rights reserved.
  • Page 17 Port ALARM_C and Port ALARM_NO composes an on-off button to provide the alarm output. If the type is NO, this button is normal open. The button becomes off when there is an alarm output. Figure 2 - 7 Alarm output © Copyright Qvis ®. All documentation rights reserved.

  • Page 18: Installation

    Please refer to Figure 3- 1 for device installation space information. You will find that there are an installation position diagram and installation screws in the accessories bag for you to install the device. Figure 3- 1 Device installation 1 © Copyright Qvis ®. All documentation rights reserved.

  • Page 19: Device Installation Steps

    2 inner hex screws from the dome driver module. Then please follow the prompt on the device to push the metal hook to the two sides. Remove the dome driver module from the chassis. See Figure 3-3. © Copyright Qvis ®. All documentation rights reserved.
  • Page 20 This is to enhance device reliability.  If you want to install Micro SD card, please refer to Chapter 3.3. © Copyright Qvis ®. All documentation rights reserved.

  • Page 21: Lens Pan Rotation Angle Setup

    Please note Figure 3-5 and Figure 3-6 are based on the IR motorized zoom camera. For the IR manual zoom camera the lock screw position and the lens angle adjustments are the same. © Copyright Qvis ®. All documentation rights reserved.

  • Page 22: Manual Zoom Lens Focus Operation

    Use the proper tool to dig through the part specified in Figure 3-7 to form a cable exit. Put the plastic decoration plug back to the chassis and then pull the cable through the side panel of the chassis. © Copyright Qvis ®. All documentation rights reserved.

  • Page 23: Cable Connection

    Step 1 Take the waterproof airproof plug out, pull the cable (diameter ranges from 4.0 to 6.0 mm) through the waterproof airproof plug (see Figure 3 – 9). Figure 3- 9 Cable connection © Copyright Qvis ®. All documentation rights reserved.

  • Page 24: Micro Sd Card Installation

    Please find the ‘SD’ mark inside the device and adjust the Micro SD card direction according to prompt direction. Insert the card to the slot and then install the Micro SD card (see Figure 2- 2 Figure 2- 2 Micro SD card © Copyright Qvis ®. All documentation rights reserved.

  • Page 25: Quick Configuration Tool

    The factory default user name is admin and password is admin. For security reasons, please modify your password after you first login. For detailed WEB operation, please refer to the Network Camera Web Operation Manual in the resource CD. © Copyright Qvis ®. All documentation rights reserved.
  • Page 26 Or you can select an IP address and then click the Login button to go to the login interface. See Figure 4-4. In Figure 4-4, you can view device IP address, user name, password and port. Please modify the corresponding information to login. © Copyright Qvis ®. All documentation rights reserved.
  • Page 27 After you logged in, the configuration tool main interface is shown as below. See Figure 4-5. Figure 4-5 Main interface For detailed information and operation instructions of the quick configuration tool, please refer to the Quick Configuration Tool User’s Manual included in the resources CD. © Copyright Qvis ®. All documentation rights reserved.

  • Page 28: Web Operation

    2. The login interface is shown as below. See Figure 5-2. 3. Please input your user name and password. 4. Default factory name is admin and password is admin. Note: For security reasons, please modify your password after you first login. © Copyright Qvis ®. All documentation rights reserved.
  • Page 29 If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the control download. Or you can lower the web browser’s security level. See Figure 5-3. Figure 5-3 IE security level © Copyright Qvis ®. All documentation rights reserved.
  • Page 30 After you logged in, you can see the main window. See Figure 5-4: Figure 5-4 Web monitoring window © Copyright Qvis ®. All documentation rights reserved.

  • Page 31: Faq

    Note  This user’s manual is for reference only. Slight differences may be found in user interface.  All the designs and software here are subject to change without prior written notice. © Copyright Qvis ®. All documentation rights reserved.
  • Page 32 For more information about our IP Cameras and other available cameras, NVRs & accessories, please visit our website: www.adata.co.uk Alternatively scan this QR code with your smart phone to be directed instantly to our website: © Copyright Qvis ®. All documentation rights reserved.

This manual is also suitable for:

Amb-vanir-2Amb-vanirm2

Table of Contents