Table of Contents
Advertisement
3.
SELF-DIAGNOSIS CODE TABLE
Self-diagnosis Code
Block
Detailed
Function
Code
C
0
4
0
C
2
1
0
C
2
2
0
C
3
1
1
C
3
1
1
C
3
1
2
C
3
1
2
C
3
1
2
C
3
1
2
C
3
1
2
C
3
1
3
C
3
1
4
C
3
1
4
C
3
2
1
C
3
2
1
C
3
2
2
C
3
2
2
C
3
2
2
C
3
2
2
C
3
2
2
C
3
2
3
C
3
2
4
C
3
2
4
E
2
0
0
E
6
1
0
E
6
1
1
E
6
1
1
E
6
2
0
E
6
2
0
DCR-PC53E/PC55/PC55E
Symptom/State
0
Non-standard battery is used.
0
Condensation.
0
Video head is dirty.
0
LOAD direction. Loading does not
complete within specified time
1
UNLOAD direction. Loading does not
complete within specified time
0
T reel side tape slacking when unloading.
1
Winding S reel fault when counting the
rest of tape.
2
T reel fault.
3
S reel fault.
4
T reel fault.
0
FG fault when starting capstan.
0
FG fault when starting drum.
2
FG fault during normal drum operations.
LOAD direction loading motor time-
0
out.
UNLOAD direction loading motor
1
time-out.
T reel side tape slacking when
0
unloading.
Winding S reel fault when counting the
1
rest of tape.
2
T reel fault.
3
S reel fault.
4
T reel fault.
0
FG fault when starting capstan.
0
FG fault when starting drum
FG fault during normal drum
2
operations
0
Data on A page or D page are rewritten.
Difficult to adjust focus
0
(Cannot initialize focus.)
Zoom operations fault
0
(Cannot initialize zoom lens.)
The abnormalities in initialization of the
focus lens and the abnormalities in
1
initialization of the zoom lens occurred
simultaneously.
Steadyshot function does not work well. (With
0
pitch angular velocity sensor output stopped.)
Steadyshot function does not work well. (With
1
yaw angular velocity sensor output stopped.)
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Make data on A page and D page correct value.
Inspect the lens block focus MR sensor (Pin qk , w; of CN1001 of
VC-379 board) when focusing is performed when the focus buttons
of the touch panel are pressed in the focus manual mode, and the
focus motor drive circuit (IC3801 of VC-379 board) when the
focusing is not performed.
Inspect the lens block zoom MR sensor (Pin qf , qh of CN1001 of
VC-379 board) when zooming is performed when the zoom lever
is operated, and the zoom motor drive circuit (IC3801 of VC-379
board) when zooming is not performed.
Check whether the flexible board of the lens is brokenÅAand check
whether it is inserted imperfectly. If there is no problem in the
flexible board, inspect the focus/zoom motor drive circuit (IC3801
of VC-379 board).
Inspect pitch angular velocity sensor (SE8002 of FB-223 board)
peripheral circuits.
Inspect yaw angular velocity sensor (SE8001 of FB-223 board)
peripheral circuits.
1-4
ENGLISH
JAPANESE
ENGLISH
JAPANESE
Correction
Advertisement
Table of Contents
