Install Connecting Rods With Pistons And Rings; Install Valve Tappets And Camshaft; Connecting Rod Torque Sequence; Determining Camshaft End Play - Kohler Command Pro ECV850 Service Manual

Install Connecting Rods with Pistons and Rings

Piston Details
A
A Side 1
C Top of Piston

Connecting Rod Torque Sequence

A
2
1
A Cylinder 1
NOTE: Cylinders are numbered on crankcase. Make
sure to install piston, connecting rod and end
cap into appropriate cylinder bore as previously
marked at disassembly. Do not mix end caps
and connecting rods.
NOTE: Proper orientation of piston/connecting rod
assemblies inside engine is extremely important.
Improper orientation can cause extensive wear
or damage. Be certain pistons and connecting
rods are assembled exactly as shown.
1. If piston rings were removed, refer to Disassembly/
Inspection and Service procedure to install new
rings.
2. Lubricate cylinder bore, piston, and piston rings with
engine oil. Compress rings of piston side 1 using a
piston ring compressor.
3. Lubricate crankshaft journals and connecting rod
bearing surfaces with engine oil.
4. Make sure FLY stamping on piston is facing toward
fl ywheel side of engine. Use a hammer with a rubber
grip and gently tap piston into cylinder. Be careful oil
ring rails do not spring free between bottom of ring
compressor and top of cylinder.
5. Install inner rod cap to connecting rod using screws.
Torque screws in increments to 11.6 N·m (103 in.
lb.). Illustrated instructions are provided in service
rod package.
19 690 01 Rev. --
C
B
B Side 2
B
4
3
B Cylinder 2
KohlerEngines.com
Align chamfer of connecting rod with chamfer of its
mating end cap. When installed, fl at faces of
connecting rods should face each other. Faces with
raised rib should be toward outside.
6. Repeat this procedure for other connecting rod and
piston assembly.

Install Valve Tappets and Camshaft

NOTE: Exhaust valve tappets are located on output
shaft side of engine, while intake valve tappets
are located on fan side of engine. Cylinder
number is embossed on outside of each cylinder
on crankcase. Valve tappets should always be
installed in same position as before disassembly.
1. Apply camshaft lubricant to contact surface of valve
tappets. Note mark or tag identifying tappets and
install them in their appropriate crankcase locations.
A small amount of grease applied to stems will hold
valve tappets up until camshaft is installed.
2. Liberally apply camshaft lubricant to lobes of
camshaft. Lubricate camshaft bearing surfaces of
crankcase and camshaft with engine oil.
3. Position timing mark of crankshaft gear at 12 o'clock
position.
4. Turn governor cross shaft clockwise until lower end
(blade) is laying against bottom of cylinder. Make
sure cross shaft remains in this position while
installing camshaft.
5. Slide camshaft into bearing surface of crankcase,
positioning timing mark of camshaft gear at 6 o'clock
position. Make sure camshaft gear and crankshaft
gear mesh with both timing marks aligned.

Determining Camshaft End Play

1. Place a new oil pan gasket into position on
crankcase.
2. Position camshaft end play checking tool over
camshaft. Use a feeler gauge to check end play
between camshaft and end play checking tool.
Camshaft end play should be between 0.147/0.495
mm (0.006/0.019 in.).
3. No shim is typically used from factory. However, if
camshaft end play is not within specifi ed range,
remove checking tool and shim as necessary.
Several color coded shims are available:
White: 0.69215/0.73025 mm (0.02725/0.02875 in.)
Blue: 0.74295/0.78105 mm (0.02925/0.03075 in.)
Red: 0.79375/0.83185 mm (0.03125/0.03275 in.)
Yellow: 0.84455/0.88265 mm (0.03325/0.03475 in.)
Green: 0.89535/0.99345 mm (0.03525/0.03675 in.)
Gray: 0.94615/0.98425 mm (0.03725/0.03875 in.)
Black: 0.99695/1.03505 mm (0.03925/0.04075 in.)
4. Reinstall end play checking tool and recheck end
play.
Reassembly
89