Yaesu FTDX9000D Operation Manual page 37

FAST/RX Switch
FAST Switch
When the A/B switch (#
ange lamp to the right of the CLAR/VFO-B knob
lights up, the CLAR/VFO-B knob (#
trolling the Sub (VFO-B) frequency; pressing the
FAST/RX switch will increase the tuning rate by a
factor of 10.
RX Switch
When the CLAR switch (#
imbedded LED is illuminated), pressing the FAST/
RX switch applies the programmed Clarifier offset
to the Main (VFO-A) receive frequency. Press the
FAST/RX switch once more to return the Main re-
ceiver to the frequency shown on the main frequency
display field; the Clarifier offset will still be present,
though, in case you want to use it again. To cancel the
Clarifier offset, press the B-MODE/CLEAR switch
(see details in # below).
BAND/MHz / TX Switch
BAND/MHz
When the A/B switch (#
ange lamp to the right of the CLAR/VFO-B knob
lights up, pressing the BAND/MHz switch allows
you to rotate this knob for selection of the Amateur
band to be used for the Sub (VFO-B) band.
TX Switch
When the CLAR switch (#
imbedded LED is illuminated), pressing the BAND/
MHz / TX switch applies the programmed Clarifier
offset to the Main (VFO-A) transmit frequency. Press
the FAST/RX switch once more to return the trans-
mitter to the Main (VFO-A) frequency shown on the
main frequency display field; the Clarifier offset will
still be present, though, in case you want to use it again.
To cancel the Clarifier offset, press the B-MODE/
CLEAR switch (see details in #
B-MODE/CLEAR Switch
B-MODE Switch
When the A/B switch (#
ange lamp to the right of the CLAR/VFO-B knob
lights up, pressing the B-MODE/CLEAR switch al-
lows you to rotate this knob for selection of the oper-
ating mode to be used on the Sub (VFO-B) band.
CLEAR Switch
When the CLAR switch (#
imbedded LED is illuminated), pressing the B-
MODE/CLEAR switch clears out any frequency off-
set you have programmed into the Clarifier register
(thereby setting the offset to "Zero").
FT 9000D O
DX PERATION
F
RONT
) is pushed, and the Or-
) will be con-
) is pressed (and its
) is pressed, and the Or-
) is pressed (and its
below).
) is pressed, and the Or-
) is pressed (and its
M
ANUAL
P C
ANEL
A/B Switch
The A/B switch controls the determines whether
the actions of the CLAR/VFO-B knob will be ap-
plied to the Main (VFO-A) band ("CLAR" option),
or the Sub (VFO-B) band ("VFO-B option").
Pressing this switch once causes the Orange lamp to
the right of the CLAR/VFO-B knob (#
up; in this case, rotation of the CLAR/VFO-B knob
affects operation on the Sub (VFO-B) band (tuning,
etc.). Pressing the A/B switch once more causes the
Orange lamp to turn off; in this instance, rotation of
the CLAR/VFO-B knob affects operations
associatedf with the Main (VFO-B) band (Clarifier
function, etc.).
[F1] ~ [F7]/DISP Keys
[F1] ~ [F7] Key
These keys are used for selection of a variety of func-
tions, depending on the TFT operation page selected.
The actual selection available at any given time is
shown on the TFT, just above the function key.
DISP (Display) Key
This key is used for selection of the desired TFT op-
eration page.
BAND Key
These keys allow one-touch selection of the desired
Amateur band (1.8 ~ 50 MHz).
What's more, the [0] ~ [9] keys may be used for direct
entry of a desired operating frequency during VFO
operation.
TFT Display (see page 40)
This 6.5-inch TFT display is used for viewing and
control of a variety of features, and it includes pages
including a World Map, World Clock, Spectrum
Scope, SWR and Transmitter Status, Log Book, Au-
dio Scope and Oscilloscope, Memory Channel list-
ing, and Menu listings, plus much more.
ONTROLS
) to light
Page 35