Table of Contents
Advertisement
8.11 List of parameters and variables, Access
Point versione Modbus RTU
In order to access the information from the system of sensors, the supervisor
connection settings are as follows:
Modbus® RTU protocol;
baud rate 9600 8, N, 2 or 19200 8, N, 2. Below is the table of supervisor variables
for the system components.
Variable Index Name
HR0
'CMD_PASSW_1'
HR1
'CMD_PASSW_2'
HR2
'CMD_PASSW_3'
HR3
'OFFLINE_MODE'
HR4
'TIME_STAMP'
HR5
'ROUTER_TX_TIME'
HR6
'CMD_PASSW_4'
HR7
'CMD_PASSW_5'
HR8
'CMD_PASSW_6'
HR9
'CMD_PASSW_7'
HR10
'AP_ALTER_ADDR'
HR11
'MIN_SELEC_ADDR'
HR12
'MAX_SELEC_ADDR'
IR0
'MACHINE_CODE'
IR1
'FW_VERSION'
IR2
'AP_TX_RADIO_LEV'
IR3
'NET_CHANNEL'
IR4
'NET_PANID'
IR5
'RES_COUNTER'
IR6
'RX_MESSAGE_CNT'
IR7
'CONNECTED_UNIT'
IR8
'ID_SER_ADDR'
IR9
'MAC_ADDR_0'
IR10
'MAC_ADDR_1'
IR11
'RX_MSG_LEVEL'
IR12
'CONN_BINDED'
IR13
'CONN_AP'
IR14
'AP_RESET_CNT'
IR15
'AP_RESET_TYPE'
IR16
'FREE_BUFFER'
IR17
'NET_PANID_EXT_3'
IR18
'NET_PANID_EXT_2'
IR19
'NET_PANID_EXT_1'
IR20
'NET_PANID_EXT_0'
IR21
'ROUTER_CONNECTED'
IR22
'ROUTER_CONN_NEARBY' 'Number of Router nearby'
IR23
'ROUTER_GOOD_SIGNAL'
CS0
'EN_CMD_PW'
IS0
'AP_CONN'
IS1
'AP_OPEN'
8.12 Installation notes
•
Fasten the Access Point to the wall with the cable gland facing downwards;
•
Connect the RS485 network to the terminal respecting the polarity;
•
Tighten the antenna in the special housing, and position it vertically to the
fl oor;
•
Connect the 12-24 Vac power supply to the terminal, ensuring the polarity
indicated for DC power supply. A 12 Vac transformer is recommended.
•
For correct operation the system must be powered at all times, in the event
of power failures there may be a unit reset time (OFFLINE) based on the data
transmission cycle.
IMPORTANT: if the same power supply is shared by more than one unit,
connect the same wire from the transformer to the power supply "-" terminal.
Description
'Command Password (1)'
'Command Password (2)'
'Command Password (3)'
'Mode Status Access-Point'
'Clock Counter as hh:mm for RX-data TimeStamp'
'Sending time to fi nd new ways (default 20sec)'
'Command Password (4)'
'Command Password (5)'
'Command Password (6)'
'Command Password (7)'
'Gateway Alternative Address (used if DipSwitch=0 default=1)'
'Minimum address allowed for devices behind Router Bridge
(default=1)'
'Maximum address allowed for devices behind Router Bridge
(default=247)'
'Unit type - machine code '
'Firmware version (Major/Minor)'
'AccessPoint Trasmission Power'
'Network Channel - ZigBee'
'Network PanId'
'Counter - seconds from last Reset'
'Counter - Rx messages from last Reset'
'Number of connected units (On-line units) end-Devices'
'Carel_ID, Serial_Address, DIP-SW value'
'Units unique identifi er Mac-Address LSB'
'Units unique identifi er Mac-Address MSB'
'Radio signal Level'
'Number of units connected through Router Bridge (Remote
Wired Network)'
'Number of units connected to AccessPoint'
'Counter - Reset number for AccessPoint'
'Type for AccessPoint Reset'
'Free Packet-Buff er ( available connection slot )'
'Network PanId Extended MSB'
'Network PanId Extended'
'Network PanId Extended'
'Network PanId Extended LSB'
'Number of Routers in the network'
'Number of Router nearby with good connection'
Enable Command Password (internal use)'
'AccessPoint connected to Radio Network ( 1=Yes)'
'AccessPoint Network Open/Closed ( 1= open)'
Tab. 8.f
Def.
0
0
0
21
0
20
0
0
0
0
1
1
247
112
2051
99
0
0
0
0
0
-
-
-
0
0
0
0
-
-
0
0
0
0
0
0
0
0
0
0
37
"Wireless probes" +0300030EN - rel. 1.0 - 16.07.2010
Min
Max
UoM
"Type R/W"
0
65535
-
0
65535
-
0
65535
-
1
63
-
0
2359
hh*100+mm
10
60
sec
0
65535
-
0
65535
-
0
65535
-
0
65535
-
1
247
-
1
247
-
1
247
-
-
-
-
-
-
-
-
-
dBm+100
0
26
-
0
65535
-
0
65535
sec
0
65535
-
0
112
-
1
247
-
0
65535
-
0
65535
-
0
100
dBm+100
0
255
-
0
32
-
0
65535
-
0
255
-
0
255
-
0
65535
-
0
65535
-
0
65535
-
0
65535
-
0
65535
-
0
16
-
0
16
-
0
1
-
0
1
-
0
1
-
ENG
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R/W
R
R
Advertisement
Table of Contents
