Important Safety Precautions; Work Area; Personal Safety; Tool Use And Care - Power Fist J1G-355C Owner's Manual

ImPORTANT SAFETy PRECAUTIONS

warnInG! read and understand all instructions before using this tool. Keep this
manual for the safety warnings and precautions, operating, inspection and maintenance
instructions. when using this tool, basic precautions should always be followed to reduce
the risk of personal injury and/or damage to the equipment.

wOrK area

1. Keep your work area clean and well lit. Cluttered and dark areas invite accidents.
2. Operate in a safe work environment. Do not use machines or power tools in damp or wet locations. Do
not expose to rain. Do not use power tools in the presence of flammable gases or liquids.
3. Keep children, bystanders and visitors away from the work area. Do not let them handle tools or
extension cords. No one should be in the work area if they are not wearing suitable protective equipment.
4. store unused equipment. When not in use, tools must be stored in a dry location to prevent rust.
Always lock up tools and keep them out of reach of children.

PersOnal saFeTy

1. use eye, face, breathing and ear protection. Always wear ANSI approved impact safety goggles,
which must provide both frontal and side protection. Wear a full face shield if your work creates metal
filings. Wear an ANSI approved dust mask or respirator when working around metal, dusts and mists.
Wear ANSI approved earplugs.
2. Do not over reach; keep proper footing and balance at all times. Proper footing and balance enables
better control of the tool in unexpected situations.
3. Dress properly, wear protective equipment. Do not wear loose clothing or jewelry as they can be
caught in moving parts. Tie back long hair. Protective, electrically non-conductive clothes and non-skid
footwear are recommended when working.
4. stay alert, watch what you are doing and use your common sense. Do not operate any machine or
tool when you are tired, under the influence of drugs, alcohol or medications.
5. use clamps or other practical ways to secure and support the work piece to a stable platform.
Holding the work piece by hand or against your body is unstable and may lead to loss of control.

TOOl use anD Care

1. use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a
larger industrial tool. The tool will perform better and safer at the task for which it was intended. Do not
modify this tool or use for a purpose for which it was not designed.
2. maintain tools with care. Keep tools clean, sharp and in good condition for a better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect tool fittings,
alignment and hoses periodically and, if damaged, have them repaired by an authorized technician
or replaced. The handles must be kept clean, dry and free from oil and grease at all times. A properly
maintained tool reduces the risk of binding and is easier to control. Sharp tools are safer than tools which
have become dull because you do not have to apply excessive amounts of force to make your cuts.
Applying excessive force can lead to slips and damage to your projects or personal injury.
3. remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the
tool or machine before connecting it. A wrench or key that is left attached to a rotating part of the tool
increases the risk of personal injury.
4. avoid unintentional starts. Be sure that the power switch is in the OFF position when not in use and
before connecting it to any power source. Do not carry the tool with fingers near or on the switch.
5. Only use the lubricants supplied with the tool or specified by the manufacturer. Other lubricants
may not be suitable and may damage the tool or even make the tool explode.
6. when not used for extended periods, apply a thin coat of lubricant to the steel parts to avoid rust.
servICe
1. Check for damaged parts. Before using any tool, any part that appears to be damaged should be
carefully checked to determine that it will operate properly and perform its intended functions. Check
for alignment and binding of moving parts, broken parts or mounting fixtures, or any other condition
that may affect proper operation. Any part that is damaged should be properly repaired or replaced
by a qualified technician.
2. when servicing, use identical replacement parts. Only use accessories intended for use with this tool.
For any technical questions, please call 1-800-665-8685
3
8287864