Related Manuals for Kranzle quadro 9/170 TST
Summary of Contents for Kranzle quadro 9/170 TST
- Page 1 Operating manual - GB - H i g h - p r e s s u r e c l e a n e r Read and conform safety instructions before use! Keep instructions in a safe place for later use and pass them on to any future user.
-
Page 2: Technical Data
Technical data Technical quadro quadro quadro data 9/170 TST 11/140 TST 12/150 TST Operating pressure, steplessly adjustable 10 - 170 bar 10 - 140 bar 10 - 150 bar max. permissible overpressure 190 bar 155 bar 165 bar Water output at nominal pressure 8.7 l/min 11.0 l/min... -
Page 3: Table Of Contents
Description Dear customer We would like to congratulate you on your new high pressure cleaner with inte- grated water tank and to thank you for the purchase. To ease your introduction to the use of the cleaner, we have provided the following pages of explanations, tips and hints, which we ask you to read before using it for the first time. -
Page 4: Connection Principle And Components
Description quadro 9/170 quadro 11/140 230V/50Hz quadro 12/150 400V/50Hz Connection principle The KRÄNZLE quadro 9/170; 11/140 and 12/150 - high pressure cleaners are mobile machines with hose drum and 20 m industrial hose. The connection principle can be seen from the illustration. Components 1 Water inlet connection with filter 6 Detergent valve... -
Page 5: Water System
Description Water supply system The water must be lead to the high pressure cleaner under pressure (2 – 8 bar ad-mission pressure). A float valve regulates the water inlet. Then, the water is sucked by the high pressure pump from the water tank and supplied to the lance under the set pressure. -
Page 6: High Pressure Hose And Spray Device
Description High pressure hose and spraying device The high pressure hose and spraying device supplied with the machine are made of high grade material. They are also optimized for the machine and marked as required by the appropriate regulations. If replacement parts are required, only such parts that are authorized by the manufacturer and which bear the markings required by the appropriate regulations may be used. -
Page 7: Total Stop System
Description With Total-Stop-System The Kränzle quadro 9/170 TS, 11/140 TS und 12/150 TS - high pressure cleaners are equipped with a Total-Stop-System. If the main switch is switched on, the motor is started by means of a pressure switch as soon as the gun is operated. The pump quickly reaches the set operating pressure. -
Page 8: Electrical Connection
The socket must be protected with a 16A delay action fuse on the mains side. KRÄNZLE quadro 9/170 TST, 11/140 TST = 230 Volt / 50 Hz KRÄNZLE quadro 12/150 TST = 400 Volt / 50 Hz... -
Page 9: Brake
Description Brake Brake not applied Brake applied Brief operating instructions : 1. Connect high pressure hose with spray gun. 2. Connect to suitable water supply. 3. Connect current (see page 8). 4. Switch on machine, operate gun and start cleaning. 5. -
Page 10: This Is What You've Purchased
This is what you’ve purchased: 1. Dirtkiller Lance with nozzle protection and high pressure nozzle Flat jet 25° 2. Spray gun M2000 with insulated handle and screw connection 3. KRÄNZLE - High pressure cleaners quadro 9/170, 11/140 and 12/150 TST with hose drum and 15 m HP hose NW 6 with steel reinforcement 4. -
Page 11: Preparation For Use
Preparation for use To control the high pressure cleaner 1. the foot against the tilt bases and 2. then pull the device towards you. 1. Check oil level. The oil level must be between the two markings on the oil dipstick. - Page 12 Preparation for use 2. Connect the high pressure lance or dirtkiller to the spray gun. 3. Unroll hose without kinks and con- nect with handgun and pump. Use max. 20 m HP hose. 4. Connection of high pressure hose from device to lance.
-
Page 13: External Suction
Preparation for use 5. The machine must be connected to the water line with cold water or up to 60° C warm water (see page 2). The hose cross section must be at least 3/4" = 16 mm (free passage). Filter 1 must always be clean. -
Page 14: When Using Detergents
To shut down the pump Suction of detergents Put chemistry sieve number 5 into the deter- gent container. Open the detergent valve (6), then the detergent is sucked in. When closing the detergent valve, the chemistry supply is automatically closed. Allow detergent to act and then wash off. -
Page 15: Safety Notes „This Is Prohibited
Safety notes As to the recoil - see notice on page 2! Apply the safety catch on the spray gun after each use, in order to prevent unintention- al spraying! - Page 16 This is prohibited ! Never direct the water jet at people or animals ! Do not damage the power cable or re- pair it incorrectly! Never pull the high pressure hose if it has formed kinks or “nooses”! Never pull the hose over sharp edges !
- Page 17 This is prohibited ! Never allow child- ren to use the high pressure cleaner ! Never direct the water jet at the ma- chine itself ! Never direct the water jet at a po- wer socket !
-
Page 18: Additional Accessories
Additional accessories for ... (on demand) Rotary scrubbing brush Order No. 41.050 1 Drain and pipe cleaning hose 10 m - Order No. 41.058.1 15 m - Order No. 41.058 Environmental, refuse disposal and water protection regulations must be observed when using the accessories! - Page 19 ... further combination possibilities Car cleaning, glass, caravan, boat etc.: ro- tary washing brush with 40 cm extension and ST 30 nipple M22 x 1.5 Cleaning pipes, channels and drains: pipe cleaning hose with KN nozzle and ST 30 nipple M22 x 1.5 Cleaning cars and all smooth surfaces: brush with ST 30 nipple M22 x 1.5 Rotary point sprayer for extreme soiling:...
-
Page 20: Small Repairs
Small repairs The nozzle is blocked! No water but the gauge shows full pressure ! but if you You should now have a Rinse the hose only get a few powerful stream of through first. drops of water water, from the lance Using the flat spray lance you remove the lance and clean... - Page 21 ...do it yourself ! Nozzle dirty or sticky! Pressure gauge does not show full pressure The high-pressure hose vibrates. Water comes out in spurts. If you do not use the high-pressure cleaner for some time the valves can stick. When a valve is the gauge or the high blocked,...
-
Page 22: Spare Parts Lists
Complete Assembly... - Page 23 quadro 9/170 - 12/150 TST...
- Page 24 Water inlet and brake...
- Page 25 quadro 9/170 - 12/150 TST Spare parts list KRÄNZLE quadro 9/170 - 11/140 - 12/150 TST Water inlet and brake Description Qty. Ord.-No Revisionsdeckel 46.512 Dichtung Revisionsdeckel 46.513 Sterngriffschraube M6 46.031 Schwimmerventil 46.250 1 Mutter R3/4“ 46.258 Kunststoffschraube 5x14 43.426 Scheibe 5,3 DIN9021 50.152 Zugfeder...
- Page 26 Pump motor...
-
Page 27: Pump Motor
quadro 9/170 - 11/140 TST Spare parts list KRÄNZLE quadro 9/170 - 11/140 TST Pump motor Description Qty. Ord.-No Ölgehäuse für AP mit Deckel und Dichtung 1 46.530 1 Motorgehäuse mit Stator Wechselstrom 46.528 Rotor mit Motorwelle 43.316 Passfeder 6 x 6 x 20 41.483 1 Motor-Lager B-Seite 6205 - 2Z 43.317... - Page 28 Pump motor...
- Page 29 quadro 12/150 TST Spare parts list KRÄNZLE quadro 12/150 TST Pump motor Description Qty. Ord.-No Ölgehäuse für AP 46.530 1 Motorgehäuse mit Stator Drehstrom 46.529 Rotor mit Motorwelle 43.316 Passfeder 6 x 6 x 20 41.483 1 Motor-Lager B-Seite 6205 - 2Z 43.317 Motor-Lager Schulterlager 7304 41.027...
- Page 30 Pump...
- Page 31 9/170 TST Spare parts list KRÄNZLE 9/170 TS T Pump with plunger, diameter 15 mm Description Qty. Ord.-No Gehäuseplatte für 15 mm Plunger 42.906 Öldichtung 15 x 24 x 7 42.907 O-Ring Viton 88 x 2 41.021 1 Plungerfeder 41.033...
- Page 32 Pump...
- Page 33 quadro 11/140 - 12/150 TST Ersatzteilliste KRÄNZLE 11/140 - 12/150 TS T Pump with plunger, diameter 18 mm Description Qty. Ord.-No Gehäuseplatte für 18 mm Plunger 41.020 2 Öldichtung 18 x 28 x 7 41.031 O-Ring Viton 88 x 2 41.021 1 Plungerfeder 41.033...
- Page 34 Unloader valve and pressure switch...
- Page 35 quadro 9/170 - 12/150 TST...
- Page 36 Valve housing...
- Page 37 KRÄNZLE 9/170 TS T...
- Page 38 Valve housing...
- Page 39 quadro 11/140 - 12/150 TST...
- Page 40 Hose drum...
- Page 41 quadro 9/170 - 12/150 TST 3333...
- Page 42 Gun and lance Description Qty. Ord.-No Pistolenschale re+li 12.450 Schraube 3,5 x 14 44.525 Reparatursatz M2000 12.454 O-Ring 9,3 x 2,4 13.273 Düsenschutz 26.002 1 Rohr 500 mm; bds. M12x1 41.527 1 ST 30 Nippel M 22 x 1,5 / M12x1 m. ISK 1 13.363 Flachstrahldüse 2003 (quadro 9/170) M2003...
- Page 43 Dirtkiller Spare parts list KRÄNZLE quadro 9/170 - 12/150 TST Dirtkiller Description Qty. Ord.-No Sprühkörper 41.520 O-Ring 6,88 x 1,68 41.521 Düsensitz 41.522 Nozzle 03 (quadro 9/170) 41.523 4 Nozzle 045 (quadro 11/140, 12/150) 41.523 Stabilisator 41.524 O-Ring 40.016 1 Sprühstopfen M12x1 IG 41.526 Rohr 400 mm lang;...
-
Page 44: Wiring Diagram
Wiring diagram... - Page 45 Wiring diagram...
-
Page 46: General Rules / Oil Change / Guarantee
General rules Inspections The machine must be inspected according to the “Guidelines for Liquid Spray De- vices” at least once every 12 months by a qualified person, to ensure that continu- ed safe operation is guarateed. The results of the inspection are to be recorded in writing. (see pages 48-49) Accident prevention The machine is designed for accidents to be impossible if used correctly. -
Page 47: Ec Declaration Of Conformity
(techn. documentation available from): Manfred Bauer, Fa. Josef Kränzle Rudolf-Diesel-Str. 20, 89257 Illertissen Nominal flow: K quadro 9/170 TST: 540 l/h K quadro 11/140 TST: 660 l/h K quadro 12/150 TST: 720 l/h comply with the following guidelines and Machine guideline 2006/42/EEC... -
Page 48: Inspection Report
Inspection report for HP cleaners HP cleaners for industrial use have to be checked by an expert every 12 months! Inspection report on annually carried out Labour Safety Inspection (UVV) according to the Guidelines for Liquid Spray Equipment. (This inspection sheet serves as proof for the completion of the retest and must be kept carefully!) Kränzle test seals: Order no. - Page 49 Inspection report for HP cleaners HP cleaners for industrial use have to be checked by an expert every 12 months! Inspection report on annually carried out Labour Safety Inspection (UVV) according to the Guidelines for Liquid Spray Equipment. (This inspection sheet serves as proof for the completion of the retest and must be kept carefully!) Kränzle test seals: Order no.
- Page 50 Warranty Guarantee The guarantee is only valid for material and manufacturing errors. Wearing does not fall within this gurantee. The instructions in our operating manual must be complied with. The operating instructions form part of the guarantee. The Guarantee is void if other parts are used than genuine Kränzle accessory parts or genuine Kränzle spare parts.
- Page 51 Notes...
- Page 52 I . K r ä n z l e G m b H E l p k e 9 7 D - 3 3 6 0 5 B i e l e f e l d Re p r i n t o n l y a l l o w e d w i t h t h e a u t h o r i z a t i o n o f K r ä n z l e A s d a t e o f 0 9 / 02 / 2 0 1 3 Made Germany...