Related Manuals for Kranzle HD 7/122
Summary of Contents for Kranzle HD 7/122
- Page 1 Original-Operating manual High-pressure cleaners HD 7/122 HD 10/122 Read and conform safety instructions before use! Keep instructions in a safe place for later use and pass them on to any future user. - GB -...
-
Page 2: Dear Customer
- containers - terraces - machines etc. - vehicles of - removing of Technical Kränzle Kränzle data HD 7/122 HD 10/122 Operating pressure, 10 - 120 bar 10 - 120 bar steplessly adjustable Nozzle size 20 03 20 045 Perm. overpressure... -
Page 3: Connection Principle
Description Water 230 V Connection principle The KRÄNZLE HD7/122 + HD10/122 - high pressure cleaners are mobile machi- nes. The design can be seen from the diagram. Components 5 Unloader valve - safety valve 1 Water inlet connection with filter 6 High pressure hose 2 Suction hose with filter (special 7 Spray gun accessory) Order no. 15.038 3 8 Interchangeable lance with high 3 High pressure pump pressure nozzle 4 Press. gauge with glycerin filling 9 Nonreturn valve (see page 8) -
Page 4: Lance With Trigger Gun
Description Water- and cleaning/detergent system Water can be connected at mains pressure to the high pressure pump or it can be sucked directly from a storage tank. The water is then forced under pressu- re by the high pressure pump to the lance. The high pressure jet is formed by the nozzle at the end of the lance. -
Page 5: Motor Protection Switch
Description Motor protection switch The motor is protected from overload by a motor protection switch, which automatically cuts out the motor in the event of overload. However should the switch trip frequently, the cause of the malfunction should be located and recti- fied (see page 6). -
Page 6: Electrical Connection
The mains plug must be fitted to a standard grounded socket with a 30mA residual current operated device. The socket must be protected with a 16A delay action fuse on the mains side. KRÄNZLE HD 7/122 230 Volt / 50 Hz KRÄNZLE HD 10/122 230 Volt / 50 Hz When using an extension cable, this must have an earthed lead which is properly connected to the socket. -
Page 7: Water Connection
Description Water connection: Please check that the high pressure cleaner has available the quantity of water specified on page 2 (techn. specifications) (Litres per minute). Test: Allow the water to run through the supply hose into a bucket for 1 minute. The received quantity of water must be at least the quantity given on page 2 !!! Lack of water causes fast wear on seals (no warranty) -
Page 8: High Pressure Hose And Spray Device
Description Brief operating instructions When operating your high pressure cleaner pay attention that it is in a horizontal position. 1. C onnect the high pressure hose with the spray gun. 2. C onnect to suitable water supply. 3. F lush the air from the pump (open and close the spray gun several times) 4. M ake the electrical connection 5. S witch on the machine with opened spray gun and commence cleaning. 6. A fter completing the work, completely empty the pump (switch the motor on for approximately 20 seconds without the suction and spray gun). - Only use clean water ! Protect from frost ! CAUTION ! Please pay attention to the regulations of your waterworks company. -
Page 9: Safety Notes
Safety notes As to the recoil - see notice on page 2! Apply the safety catch on the spray gun after each use, in order to prevent unintentional spraying! Always aim the underbody lance. Note when using an angled underbody lance, like for example lance no. 41.075 1, that there is a certain amount of torque in the recoil. (Amount of torque 26 Nm) -
Page 10: This Is What You've Purchased
This is what you’ve purchased: 1. Spray lance with high pressure nozzle 2. Spray gun with insulated pistol grip and screw connection 3. KRÄNZLE - High pressure cleaners HD7/122 / HD 10/122 4. Operating instructions 4. Steel braided high pressure hose 10 m, NW 6 5. Water inlet components is already installed... -
Page 11: Preparation For Use
Preparation for use 1. Check oil level Oil has to be visible in the oil-level sight glass 2. Connect the high pressure lance to the spray gun. 3. Unroll hose without kinks and con- nect with handgun and pump. Max. extension 20 m-HP hose or 2 x 10 m with hose connections. High pressure hose connected to machine and spray gun. - Page 12 Preparation for use 4. The machine can be connected to a pressurised water line with 60°C hot water (see page 2). Ensure that the water supply is clean when sucking from external sources. The hose cross section must be at least 1/2“ = 12.7 mm (free passage). Filter 1 must always be clean. Please make sure that the filter is clean before using your high pressure cleaner. CAUTION ! When running your high pressure cleaner with hot water of 60° C raised temperatures occur. Do not touch the pump without safety gloves! 5. Maximum induction height 1.0 m (only HD 7/122) see technical data on page 2 Water...
-
Page 13: Adjusting The Pressure
Preparation for use Adjusting the pressure This is accomplished by turning the handwheel. The default setting is maximum pressure. To shut down the pump: 1. Switch off the machine. 2. Cut off the water supply. 3. Open the spray gun briefly until the pressure is released. 4. Apply the safety catch on the spray gun. 5. Remove the water hose and spray gun. 6. Drain the pump: switch on the motor for approx. 20 seconds. 7. Pull the plug from the socket. 8. Winter: store the pump in rooms above 0°C. 9. Clean the water filter. - Page 14 This is prohibited ! Never allow children to use the high pres- sure cleaner ! Never direct the wa- ter jet at the machi- ne itself ! Never direct the water jet at a power socket !
- Page 15 This is prohibited ! Never direct the wa- ter jet at people or animals ! Do not damage the po- wer cable or repair it incorrectly ! (Replace defective or damaged cables imme- diately ! Never work with a de- fective appliance !) Never pull the high pres- sure hose if it has for-...
- Page 16 15 m - Order No. 41.058 Underbody lance Order No. 41.075 Flat brush Order No. 41.073 Dirtkiller 028 (HD 7/122) Order No. 41.570-028 Dirtkiller 042 (HD 10/122) Order No. 41.570-042 Environmental, refuse disposal and water protection regulations must be observed when...
- Page 17 ... for further combination possibilities Car cleaning, glass, caravan, boat etc. rotary washing brush with 40 cm exten- sion and ST 30 nipple M 22 x 1.5 Cleaning pipes, channels and drains: pipe cleaning hose with KN nozzle and ST 30 nipple M 22 x 1.<<<<<5 <...
-
Page 18: Small Repairs
Small repairs - Nozzle dirty or sticky! Pressure gauge does not show full pressure. The high-pressure Water comes out in spurts. hose vibrates. If you do not use the high-pressure cleaner for some time the valves can stick the gauge When a valve is blocked, or the high shows little pressure pressure or hose vibra- no pressure tes! at all, and remove the valve screw, the valve and the o-ring. -
Page 19: Do-It-Yourself
- Do it yourself! The nozzle is blocked! No water but the gauge shows full pressure ! but if you You should now have Rinse the hose only get a few a powerful through first. stream of drops from water, the lance Using the flat spray lance you remove the lance and clean only have to clean the front the nozzle. -
Page 20: Small Repairs - Do It Yourself
Small repairs - Do it yourself! Stopping leaks from hose or gun After closing the gun the manometer shows full pressure ! The pressure regulator switches on and off continuously! If the Pull out the First dis- manometer power plug! connect the shows full hose! pressure, Press the trigger to release the pressure!!! Clean the return Then unscrew element or replace the pump outlet the O-Ring ! with an open-jew... -
Page 21: Gun With Lance
13.273 Düsenschutz M12x1 26.002 1 Rohr 500 mm; bds. M12x1 41.527 1 ST 30 Nippel M 22 x 1,5 / R1/4“ m. ISK 13.363 Flachstrahldüse 028 (bei HD 7/122) M20028 54.1 Flachstrahldüse 042 (bei HD 10/122) M20042 Aluminium-Dichtring 13.275 M2000-Pistole kpl. -
Page 22: Complete Assembly
Complete assembly... - Page 23 HD 7/122 / HD 10/122 Spare parts list KRÄNZLE HD 7/122 / HD 10/122 Complete assembly Description Qty. Ord.-No Tragbügel 44.581 Gummiprofilleiste 41.098 1 Senkschraube M6x20 43.473 1 Gummipuffer 30 x 20 46.023 1 Scheibe 8,4 41.409 Mutter DIN985 M8 41.410...
- Page 24 Motor...
- Page 25 KRÄNZLE HD 7/122 / HD 10/122 Spare parts list KRÄNZLE HD 7/122 / HD 10/122 Motor Description Qty. Ord.-No Ölgehäuse mit Dichtung, Deckel Öldichtung, Schulterlager 44.501 Stator (HD 7/122) 23.001 2 Stator (HD 10/122) 23.002 4 Motorwelle mit Rotor (HD 7/122) 43.104...
- Page 26 Transmission...
- Page 27 KRÄNZLE HD 7/122 / HD 10/122 Spare parts list KRÄNZLE HD 7/122 / HD 10/122 Transmission Description Qty. Ord.-No Gehäuseplatte 43.003 Öldichtung 14 x 24 x 7 41.631 O-Ring 83 x 2 43.039 Plungerfeder 43.040 Federdruckscheibe 14 mm 43.041 Plunger 14 mm AZ-L 49.021...
-
Page 28: Valve Housing
Valve housing... - Page 29 KRÄNZLE HD 7/122 / HD 10/122...
- Page 30 ST 30-Nippel M 22 x 1,5 / M 12 x 1 ISK 13.363 Kappe vorn für Schmutzkiller 41.528 1 Kappe hinten für Schmutzkiller 028 (HD 7/122) 1 41.542 3 12.1 Kappe hinten für Schmutzkiller 042 (HD 10/122) 1 41.540 2 Rep.-Satz Schmutzkiller 028...
- Page 31 Wiring diagram / Warranty Wiring diagram for KRÄNZLE HD 7/122 / HD 10/122 C : 40 µF braun = brown blau = blue schw = black = red = yellow Terminal strip = green = white Weber-Unimat WT 22 - 551...
-
Page 32: General Rules
General rules Inspections The machine must be inspected according to the “Guidelines for Liquid Spray De- vices” at least once every 12 months by a qualified person, to ensure that contin- ued safe operation is guarateed. The results of the inspection are to be recorded in writing. -
Page 33: Ec Declaration Of Conformity
High-pressure-cleaners Hochdruckreiniger Nettoyeurs À Haute Pression I. Kränzle GmbH Elpke 97 33605 Bielefeld EC declaration of conformity Kränzle HD 7/122 We hereby declare, Kränzle HD 10/122 that the high-pressure models: Manfred Bauer, Fa. Josef Kränzle (techn. documentation available Rudolf-Diesel-Str. 20, 89257 Illertissen from): HD 7/122: 420 l/h; HD 10/122: 600 l/h Nominal flow Machine guideline 2006/42/EEC comply with the following guidelines Specification for electromagnetic and specifications and their amend- compatibility 2004/108/EEC... - Page 34 Notes...
- Page 35 Notes...
- Page 36 Reprint only allowed with the authorization of As date of 2013/01/15...