Front Panel; Rear Panel - Shure Axient AXT400 User Manual

Front Panel

1 2
sync RF
AXT400
A 470-698 MHz
A
OL
Dual Wireless Receiver
3
① Sync - Infrared (IR) Port
Infrared (IR) port. For sending parameter presets
(IR Preset) to a transmitter and linking the
transmitter and receiver to the same channel.
② Squelch LEDs
• Blue (On) = transmitter signal detected
• Off = no signal or signal squelched because of
poor reception or no tonekey
③ RF LEDs
Indicates the RF signal strength from the
transmitter.
• Amber (1-5) = -90 to -70 dBm in 5 dBm
increments
• Red = RF overload
④ Audio LEDs
Indicates the audio signal strength from the
transmitter.
• Green = signal present
• Yellow = normal peak
• Red = overload
To correct an overload, adjust the transmitter gain.

Rear Panel

1
2
AXT400
Input 100-240 V ~ 50/60 Hz 0.8A max. Output 100-240~
(5.8A max. outlet loaded) 5A max. 50/60 Hz UNSW.
① AC power primary switch
AC main power switch.
② AC power in
IEC connector 100 - 240 V AC.
③ AC power cascade
Use IEC extension cables to connect up to 5 rack
components to a single AC power source.
④ Network speed LED (amber)
• Off = 10 Mbps
• On = 100 Mbps
⑤ Ethernet ports: Class 1 PoE enabled (2)
Connect to an Ethernet network to enable remote
control and monitoring.
⑥ Network status LED (green)
• Off = no network link
• On = network link active
• Flashing = network link active, flash rate
corresponds to traffic volume
5 6
navigate
audio
B
4
⑤ LCD display
Each channel has an LCD display for viewing
settings and parameters.
⑥ Menu navigation buttons
Use to select and navigate through parameter
menus.
⑦ Enter button
The Enter button flashes when an action or
parameter change is pending. Press Enter to save
the value.
⑧ Exit button
Cancels parameter changes or returns to a
previous menu screen.
⑨ Control wheel
• Push to select menu items for editing
• Turn to edit a parameter value
⑩ Monitor clip LED
Indicates audio overload when illuminated.
⑪ Monitor output LED
Indicates channel selection for monitoring.
3 4 6 7
AES3 output
in
word
clock
thru
Term 75
Class 1 PoE
5 8 9
⑦ Word clock input
Connect to resolve the AXT400 AES3 digital
output to an external word clock source.
⑧ Word clock thru output
Passes word clock signal to additional
components.
⑨ Word clock termination switch
Set to thru when passing signal to additional
components. Set to 75Ω when thru connection is
not used.
⑩ AES3 digital audio output
24-bit digital audio output for channel 1 and
channel 2.
⑪ Line/Mic switch
Changes the output level 30 dB (XLR outputs
only).
⑫ Transformer balanced XLR audio output
For channel 1 and channel 2.
⑬ Ground lift switch
Lifts the ground from pin 1 of the XLR connector
and the sleeve of the ¼" jack.
2 5
RF audio
A B
OL
3 4
10 12 14
analog outputs receiver 2
line lift
line
mic GND
mic
11 13
4
10 12
6 7 9
navigate control monitor
clip
push
enter
1
2
exit
push
8 11 13
⑫ Monitor volume knob
Adjusts monitor volume. Push to monitor channel
1 or channel 2.
⑬ Monitor jack
6.5 mm (1/4") output jack for headphones.
⑭ Power switch
Power the unit on or off.
12 14 15
analog outputs receiver 1
16
lift
GND
B
11 13
17
⑭ Transformer balanced 1/4" output jack
For channel 1 and channel 2.
⑮ RF antenna input jacks
For antenna A and antenna B.
⑯ RF input status LED
Indicates the voltage status of the RF input.
• Green = DC voltage on
• Red flashing = fault condition
• Off = DC voltage off
⑰ RF cascade ports
Passes the RF signal from one receiver to the
next, allowing up to 5 receivers to share a single
pair of antennas.
⑱ Temperature activated fan
Ensures top performance in high temperature
environments. Clean fan screen as needed to
maintain airflow.
14
power
antenna
18
in
12.7V OUT
150 mA
cascade
out
A