Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Stairville LED PAR 18
Summary of Contents for Stairville LED PAR 18
- Page 1 LED PAR 18 / 56 / 64 Owner‘s Manual LED PAR SPOT with DMX input and output...
-
Page 2: Table Of Contents
Congratulations on your purchase of this LED PAR Light. To get the most from your equipment you must read all of this manual before using it first time. Table of Contents 1. Safety Instruction ....................3 2. Introduction ......................4 2.1 Supported function modes ................4 3 Overview ........................6 3.1 Back view ......................6 3.2 DMX operation .....................7... -
Page 3: Safety Instruction
1. Safety Instruction You have to carefully read the instruction, which includes important information about the installation, operation and maintenance. • Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that he also receives this instruction booklet thus giving them the necessary information about the use and general warnings regarding the unit. -
Page 4: Introduction
2. Introduction The main feature of this LED PAR is, that it can be used as a 4-channel DMX controller. In this mode 4 LED PARs have to be connected with XLR cables on their DMX In-/Outputs. The first LED PAR has to be set to DMX master mode. Now the LED PAR in master mode sends control signals to the connected slaves. - Page 5 There are different patterns available, e.g. all connected LED PARs do the same, each shows different patterns, chaser programs, fade in – fade out patterns and fade over patterns. The steps of the patterns can be controlled by music beat or by a potentiometer. The music sensitivity is controllable.
-
Page 6: Overview
3 Overview 3.1 Back view This picture shows the rear panel of the LED PAR. DMX-Input: In case of external DMX control, the DMX cable is connected here. DMX input pin Signal Ground Signal „―“ Signal „+“ DMX-Output: Connect the DMX cable for the next unit here. DMX output pin Signal Ground... -
Page 7: Dmx Operation
3.2 DMX operation 3.2.1 Building a serial chain Connect the DMX output of the first unit in the DMX chain with the DMX input of the next fixture. Always connect one output with the input of the next unit until all fixtures are connected. The last unit of the DMX chain has to be terminated with a resistor. -
Page 8: Auto Change Mode
5. Auto change mode The LED PAR shows different colours depending on speed selection. In this mode the LED PAR is used stand alone, the DMX output/input is not used. 5.1 Mode setting To enable the auto change mode, set the 4 pin DIP switch on the rear panel of the LED PAR according to the this table: SW1 Mode auto change... -
Page 9: Auto Fade Mode
6. Auto fade mode The LED PAR shows different fading colours depending on speed selection. In this mode the LED PAR is used stand alone, the DMX output/ input is not used. 6.1 Mode setting To enable the auto fade mode, set the 4pin DIP switch on the rear panel of the LED PAR according to the this table: SW1 Mode auto fade... -
Page 10: Manual Mode
SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 Colour pattern selection compatible mode - old pattern style 100% colour change, fade in and out 100%, 50% colour change, fade in and out 100%, 75%, 50%, 25% colour change, fade in and out 100% colour change, fade in 100%, 50% colour change, fade in... - Page 11 SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 Red colour brightness 100% 0 = DIP switch is set to off. 1 = DIP switch is set to on. X = see table below. 7.2.2 Green Colour The green colour may be set by the 10pin DIP switch on the rear panel of the LED PAR according to the following table: SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 Green colour brightness 100%...
-
Page 12: Dmx Slave 5-Channel Mode
8. DMX slave 5-channel mode The item is controlled by 5 DMX channels according the table below. With DIP switch 1 to 9 the first DMX channel to receive is set. 8.1 Mode setting To enable the DMX slave 5ch mode, set the 4pin DIP switch on the rear panel of the LED PAR according to the this table: SW1 Mode DMX slave 5-channel... -
Page 13: Set Up Of The First Dmx Receiving Channel
Channel 4 value Function – Blue colour 0% – 100% Channel 5 value Function – no function – no speed – value 11 to 100, fast speed to low speed – no function – no speed – speed control by unit, by music or potentiometer 8.4 Set up of the first DMX receiving channel The value of DIP switch 1 to 9 is binary coded. -
Page 14: Dmx Master 5Ch Mode
8.5.2 Example B, first DMX receive channel is 22 SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 First DMX receive channel The unit starts to receive with the DMX CH22. The item consumes CH22, CH23, CH24, CH25, CH26. 8.5.3 Example C, first DMX receive channel is 272 SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 First DMX receive channel The unit starts to receive with the DMX CH272. -
Page 15: Dmx Usage For 5-Channel Control
SW1 Mode speed control by potentiometer speed control by music 0 = DIP switch is set to off. 1 = DIP switch is set to on. X = see information below. 9.3 DMX usage for 5-channel control The LED PAR in master mode sent DMX data according to the table below. -
Page 16: Colour Pattern Setting
9.4 Colour pattern setting The colour patterns may be set by the 10pin DIP switch on the rear panel of the LED PAR according to the following tables: 9.4.1 Colour patterns All LED PARs are on and changing colours. SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 Colour pattern selection 4ch, Pattern 1, all on, all do the same 4ch, Pattern 2, all on, all do the same 4ch, Pattern 3, all on, all do the same... - Page 17 SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 Colour pattern selection 4ch, Pattern 1, all on, all do the same 4ch, Pattern 2, all on, all do the same 4ch, Pattern 3, all on, all do the same 4ch, Pattern 1, every unit has his own pattern, with fade over 4ch, Pattern 2, every unit has his own...
-
Page 18: Examples
0 = DIP switch is set to off. 1 = DIP switch is set to on. 9.4.4.2 Two LED PAR of four is on SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 Colour pattern selection chaser pattern 1, right to left, new colour each step chaser pattern 1, right to left –... - Page 19 Connection: MASTER SLAVE1 SLVAE2 SLAVE3 UNIT1 UNIT2 UNIT3 UNIT4 Master setup: Master unit, UNIT1, needs to be set according to this table: SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 Colour pattern selection chaser pattern 1, right to left, same colour each step SW1 Mode DMX master 5ch, speed control by potentiometer...
- Page 20 9.5.2 Example B This example shows how to set up eight LED PARs to be controlled in 5ch DMX master mode. The patterns are still send out for 4channels. Connection: MASTER SLAVE1 SLAVE2 SLAVE3 SLAVE4 SLAVE5 SLAVE6 SLAVE7 UNIT1 UNIT2 UNIT3 UNIT4 UNIT5...
- Page 21 The items consumes ch16, ch17, ch18, ch19, ch20. SLAVE4: SLAVE4, UNIT5, DMX start channel 1: 10 Pin DIP switch 4 Pin DIP switch SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 SW4 SW3 SW2 SW1 The item start to receive with the DMX channel 1. The items consumes ch1, ch2, ch3, ch4, ch5.
-
Page 22: Dmx Slave 3-Channel
10 DMX slave 3-channel The 3channel slave mode is for use with a standard DMX controller. The LED PAR can be controller with all 512 channels. Each colour is controlled by one DMX channel. All 512 DMX channels can be used. DIP switch 1 to 9 sets the first channel to receive. -
Page 23: Examples
The maximum first receive channel is channel 510. In case of chosen first receive channel bigger than 510, the maximum receive channel is still 510. 10.4 Examples 10.4.1 Example A, first DMX receive channel is 1 SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 First DMX receive channel The item starts to receive with the DMX CH1. -
Page 24: Mode Setting
11.1 Mode setting To enable the DMX master 3ch mode, set the 4pin DIP switch on the rear panel of the LED PAR according to the this table: SW1 Mode DMX master 3-channel 0 = DIP switch is set to off 1 = DIP switch is set to on X = see information below/above 11.2 Speed setting... -
Page 25: Colour Pattern Setting
11.4 Colour pattern setting Same settings as in the “DMX master 5ch” mode, chapter 9.4. 11.5 Examples 11.5.1 Example A This example shows how to set up four LED PARs to be controlled in 3ch DMX master mode. Connection: MASTER SLAVE1 SLAVE2 SLAVE3... - Page 26 SLAVE3: SLAVE3, UNIT4, DMX start channel 10: 10 Pin DIP switch 4 Pin DIP switch SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 SW4 SW3 SW2 SW1 The item start to receive with the DMX CH10. The items consumes ch10, ch11, ch12. 11.5.2 Example B This example shows how to set up eight LED PARs to be controlled in 3ch DMX master mode.
- Page 27 The item start to receive with the DMX CH7. The items consumes ch7, ch8, ch9. SLAVE3: SLAVE3, UNIT4, DMX start channel 10: 10 Pin DIP switch 4 Pin DIP switch SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 SW4 SW3 SW2 SW1 The item start to receive with the DMX ch10.
- Page 28 SLAVE7: SLAVE7, UNIT8, DMX start channel 10: 10 Pin DIP switch 4 Pin DIP switch SW10 SW9 SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1 SW4 SW3 SW2 SW1 The item start to receive with the DMX ch10. The items consumes ch10, ch11, ch12.
-
Page 29: Technical Specifications
12 Technical Specifications 12.1 LED PAR64 and Studio PAR 12.1.1 18 LEDs, 1W Number of LEDs 18 LEDs, 1W Power supply see rating label Weight 2,5Kg/4,5kg 12.1.2 24 LEDs, 1W Number of LEDs 24 LEDs, 1W Power supply see rating label Weight 2,5Kg/4,5kg 12.1.3... -
Page 30: Disposal
13. Disposal Do not dispose of the device at the end of his operating life in your normal domestic waste. This device is subject to the European Guidelines 2002/96/EC. • Have the product disposed of by a professional disposal company of by your communal disposal facility. - Page 32 © 2010 Musikhaus Thomann e. K. Treppendorf 30 • 96138 Burgebrach Germany • www.thomann.de...