Korg X50 Operation Manual Page 107

Korg x50 music synthesizer operation guide.
Hide thumbs
Tone10: [–] button
Tone11: [./HOLD] button
Tone No.
Creating an example pattern
1. Set "Step (Step No.)" to 01, and press the [0]
button.
2. Set "Step (Step No.)" to 02, and press the [1]
button.
3. Set "Step (Step No.)" to 03, and press the [2]
button.
4. Set "Step (Step No.)" to 04, and press the [1]
button.
5. Set "Step (Step No.)" to 05, and press the [3]
button.
6. Set "Step (Step No.)" to 06, and press the [1]
button.
7. Set "Step (Step No.)" to 07, and press the [2]
button.
8. Set "Step (Step No.)" to 08, and press the [1]
button.
9. When you play the keyboard as shown in the
illustration, the arpeggiator will begin playing.
Tone 0 corresponds to the pitch of the lowest
key of chord you play on the keyboard. (If
"Sort" is unchecked, it will correspond to the
pitch of the first note you play.)
10.For steps 01–08, make settings for "Ptch (Pitch
Offset)," "Gt (Gate)," "Vel (Velocity)," and
"Flam."
4
3
2
1
0
01
05
Step No.
Lgth(Length)
Creating a user arpeggio pattern
"Ptch (Pitch Offset)": This offsets the pitch of
the arpeggio note in semitones up or down.
You can input the same tone for each step, and
change the "Ptch (Pitch Offset)" value for each
to create a melody using a single tone.
(☞"Melody pattern")
"Gt (Gate)": Specify the length of the arpeggio
note for each step. With a setting of LGT, the
note will continue sounding either until the
next note of the same tone or until the end of
the pattern. With a setting of Off, the note will
not sound.
"Vel (Velocity)": Specify the strength of the note.
With a setting of Key, the note will sound at the
strength with which it was actually played.
Note: The "Gt (Gate)" and "Vel (Velocity)"
settings you make here will be valid if the "Gt
(Gate)" and "Vel (Velocity)" parameters (PROG
7: Ed–Arp/Ctrls, Setup page) of the program
selected in Program mode are set to Step. If
these parameters have a setting other than
Step, the "Gt (Gate)" and "Vel (Velocity)" that
were specified for each individual step will be
ignored, and all notes of the arpeggio will
sound according to the settings in PROG 7: Ed–
Arp/Ctrls. Be sure to verify the settings of the
program.
Note: Before you set "Gt (Gate)," move the
REALTIME CONTROLS C-mode [ARP-GATE]
knob to the center position (12 o'clock).
Note: Before you set "Vel (Velocity)," move the
REALTIME CONTROLS C-mode [ARP-
VELOCITY] knob to the center position (12
o'clock).
11.To change the user arpeggio pattern name, use
the Utility "Rename Arpeggio Pattern"
(☞p.112).
12.If you wish to save the edited user arpeggio
pattern to internal memory, be sure to Write the
user arpeggio pattern (☞p.104).
If you turn off the power without writing, the
edited contents will be lost.
13.If you wish to save the state of the program at
the same time, return to Program mode and
write the program (☞p.45).
101

Advertising

   Also See for Korg X50

   Related Manuals for Korg X50

Comments to this Manuals

Symbols: 0
Latest comments:
  • Mike Saunders Jun 24, 2017 04:35:
    Great manual a must for any owner to have also great site for download
  • sonny May 20, 2016 06:52:
    I dont understand manual user korg x50 in english langue.can you send manual user korg x50 in indonesia langue..
  • sonny May 20, 2016 06:52:
    I dont understand manual user korg x50 in english langue.can you send manual user korg x50 in indonesia langue..
  • sonny May 20, 2016 06:22:
    I dont understand manual user korg x50 in english langue.can you send manual user korg x50 in indonesia langue..