Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Champion Power Equipment 100133
Summary of Contents for Champion Power Equipment 100133
- Page 1 OWNER’S MANUAL AND OPERATING INSTRUCTIONS 20 Ton LOG SPLITTER MODEL NUMBER 100133 12039 Smith Ave. SAVE THESE INSTRUCTIONS Santa Fe Springs CA 90670 Important Safety Instructions USA / 1-877-338-0999 MADE IN CHINA are included in this manual. REV 100133-20141031 www.championpowerequipment.com...
- Page 2 Have questions or need assistance? Do not return this product to the store! WE ARE HERE TO HELP! Visit our website: www.championpowerequipment.com for more info: • Product Info & Updates • Tech Bulletins • Frequently Asked Questions • Product Registration –...
-
Page 3: Table Of Contents
100133 20 Ton LOG SPLITTER TABLE OF CONTENTS Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . 18 Introduction . -
Page 4: Introduction
Introduction Accessories Congratulations on your purchase of a Champion Champion Power Equipment manufactures and sells Power Equipment log splitter . CPE designs and builds accessories designed to help you get the most from your log splitters to strict specifications . With proper use purchase . -
Page 5: Manual Conventions
. Please call our help line at 1-877-338-0999 situation which, if not avoided, could result in death or serious injury . CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury . REV 100133-20141031... -
Page 6: Safety Rules
Keep work zone clear of debris while working to can start fires around dry vegetation . ensure safe footing . A spark arrestor may be required . The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements . REV 100133-20141031... - Page 7 . DO NOT expose log splitter to excessive moisture, dust, or dirt . DO NOT allow any material to block the cooling slots . DO NOT use the engine if: – Equipment sparks, smokes or emits flames – Equipment vibrates excessively REV 100133-20141031...
-
Page 8: Training
. Make sure you comply with local, state, and federal codes . Take appropriate fire-fighting equipment with you . 10 . Log splitters should be used only for splitting wood . Do not use for other purposes unless the manufacturer provides attachments and instructions . REV 100133-20141031... -
Page 9: Operation
. 11 . Use only your hand to operate the log splitter controls . 12 . Do not refuel the engine until it has cooled for several minutes . REV 100133-20141031... -
Page 10: Controls And Features
(12) Support Leg – Supports log splitter while Mounting Plates – Holds hydraulic cylinder in operating . Raise leg for towing . place . (13) Engine – 196cc, OHV, 4-stroke, air cooled . Splitting Beam & Hyrdaulic Oil Tank REV 100133-20141031... -
Page 11: Assembly
M12x80 bolts into the bolt holes on the bottom of the axle and through the base plate on the bottom of the hydraulic oil tank below the splitting beam . Secure with two M12 lock nuts . Tighten . Do not overtighten .(C) REV 100133-20141031... -
Page 12: Install The Tow Bar And Support Leg
Do not tow with support leg in the down position or if loose . The support leg must be locked in the upright position before towing . Towing the unit with the support leg in the down position or loose may cause property damage and/or injury . REV 100133-20141031... -
Page 13: Install The Thrust Plate And Cylinder
NOTE The pump outlet connection does NOT require teflon tape . The o-ring seals against the face of the fittings on the pump and hose . Tighten to approximately 12 ft-lb . Over-tightening can damage the pump . REV 100133-20141031... -
Page 14: Install The Multi-Wedge And Log Catchers
(2) M10x25 bolts, ø10 washers, and M10 nuts . ø10 washers, and M10 nuts . 11 . Tighten . Do not over tighten . 11 . Tighten . Do not over tighten . REV 100133-20141031... -
Page 15: Add Engine Oil
Check oil often during the break-in period . Refer to the NOTE Maintenance section for recommended service intervals . Synthetic oil may be used after the 5 hour initial break-in period . Using synthetic oil does not increase the recommended oil change interval . REV 100133-20141031... -
Page 16: Add Engine Fuel
. It is advisable to always shut off the fuel supply, run the engine to fuel starvation and drain the tank when the equipment is not in use for more than 30 days . REV 100133-20141031... -
Page 17: Add Hydraulic Oil
. The oil sight glass has a marker 8 . Check oil level daily and before each use, and add oil for the acceptable level of oil . If oil is below the marker, add oil as needed . as needed . REV 100133-20141031... -
Page 18: Operation
. CAUTION When backing up, use caution . Because of the short distance between the ball hitch and tires, the log splitter can turn sharply / abruptly and come in contact with your towing vehicle REV 100133-20141031... -
Page 19: Starting The Engine
. plug fouling/engine flooding due to the lack of incoming air . This will cause the engine not to start . 7 . As engine warms up, move the choke lever (Item D) to “Run . ” REV 100133-20141031... -
Page 20: Log Splitter Operation
3 . Load a log onto the beam against the thrust plate . To alleviate high altitude issues other than the natural CAUTION power loss, Champion Power Equipment can provide a high altitude carburetor main jet . The alternative main Back injury can result from lifting logs onto the log splitter jet and installation instructions can be obtained by if proper lifting techniques are not used . -
Page 21: Maintenance And Storage
Inspect all air vents and cooling slots to ensure that they are clean and unobstructed . Clean spark arrester every 100 hours (if equipped) . Check and tighten all bolts and nuts before operating the log splitter . REV 100133-20141031... -
Page 22: Maintenance Schedule
4 . Replace oil drain plug . *To be performed by knowledgeable, experienced owners or Champion Power Equipment certified dealers . 5 . Remove R3/4 screw and add up to 2 . 1 gallons (7 .9 L) of hydraulic oil . -
Page 23: Specifications
– Intake: 0 . 1 3 – 0 . 1 7 mm (0 .005 – 0 .007 in .) – Exhaust: 0 . 1 8 – 0 .22 mm (0 .007 – 0 .009 in .) Note: Tech bulletin regarding the valve adjustment procedure is on www .championpowerequipment .com . REV 100133-20141031... -
Page 24: Parts Diagram
100133 ENGLISH SPECIFICATIONS Parts Diagram REV 100133-20141031... -
Page 25: Parts List
GB/T 56-1988 (M18) Nut M18 PMJ22D-05-03 Wheel PMJ15-16 GB/T 9459- Slotted Nut M20x1 .5 PMJ22D-07 Front Support Leg 1988(M20X1 .5) PMJ22D-06 Base Tube PMJ22J-05-02 Axle Cap GB/T 848-2002 (Ø12) Washer Ø12 PMJ22D-09 Single Wedge GB/T 5782-2000(M12X90) Bolt M12×90 REV 100133-20141031... -
Page 26: Engine Parts Diagram
100133 ENGLISH SPECIFICATIONS Engine Parts Diagram REV 100133-20141031... -
Page 27: Engine Parts List
2 .15 .002(F6RTC) Spark Plug (F6RTC) 22 .061000 .00 Recoil Assembly 1 .5789 .0855 Flange Bolt M8×55 24 .101000 .00 Muffler Assembly 23 .040017 .00 Oil Seal, Valve 24 .091000 .02 Air Cleaner Assembly 21 .040003 .00 Valve Spring REV 100133-20141031... -
Page 28: Troubleshooting
Contact Customer Service Excessive bouncing while towing Under-inflated tires Inflate tires to proper pressure . Refer to tire sidewall For further technical support: Technical Service Mon – Fri 8:30 AM – 5:00 PM (PST/PDT) Toll Free: 1-877-338-0999 tech@championpowerequipment .com REV 100133-20141031... -
Page 29: Warranty
Warranty Qualifications – Accessory parts such as starting batteries, and storage covers . Champion Power Equipment (CPE) will register this – Failures to due acts of God and other force majeure warranty upon receipt of your Warranty Registration Card events beyond the manufacturer’s control . - Page 30 The United States Environment Protection Agency (U.S. EPA.) and the California Air Resources Board (CARB) Emission Control System Warranty Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air Resources Board (CARB) emission regulations.
- Page 31 EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1995 and later model year California small off-road engines (for other states, 1997 and later model year engines). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
- Page 32 You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours.
Need help?
Do you have a question about the 100133 and is the answer not in the manual?
Questions and answers