Champion Power Equipment 100425 Operator's Manual
  1. Manuals
  2. Brands
  3. Champion Power Equipment Manuals
  4. Log Splitter
  5. 100425
  6. Operator's manual

Champion Power Equipment 100425 Operator's Manual

34 ton full beam log splitter
Hide thumbs Also See for 100425:
Table of Contents

Advertisement

Quick Links

READ AND SAVE THIS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product.
Failure to do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
Made in China - REV 20170613
REGISTER YOUR PRODUCT ONLINE
at championpowerequipment.com
OPERATOR'S MANUAL
34 TON FULL BEAM LOG SPLITTER
SERIAL NO. LABEL
or visit championpowerequipment.com
Champion Power Equipment, Inc., Santa Fe Springs, CA USA
MODEL #100425

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 100425 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Champion Power Equipment 100425

Summary of Contents for Champion Power Equipment 100425

  • Page 1 Failure to do so could result in serious injury. This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. Made in China - REV 20170613 Champion Power Equipment, Inc., Santa Fe Springs, CA USA...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS 100425 - 34 TON FULL BEAM LOG SPLITTER TABLE OF CONTENTS Maintenance Schedule .........

  • Page 3: Introduction

    INTRODUCTION 100425 - 34 TON FULL BEAM LOG SPLITTER INTRODUCTION SAFETY DEFINITIONS Congratulations on your purchase of a Champion Power The purpose of safety symbols is to attract your attention to Equipment (CPE) product. CPE designs, builds, and supports possible dangers. The safety symbols, and their explanations, all of our products to strict specifications and guidelines.

  • Page 4: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 100425 - 34 TON FULL BEAM LOG SPLITTER IMPORTANT SAFETY INSTRUCTIONS DANGER Rotating parts can entangle hands, feet, hair, clothing and/ WARNING or accessories. Traumatic amputation or severe laceration California Proposition 65: This product contains chemicals can result.

  • Page 5: Fuel Safety

    IMPORTANT SAFETY INSTRUCTIONS 100425 - 34 TON FULL BEAM LOG SPLITTER WARNING CAUTION Projectile Hazard Parts of the hydraulic circuit (cylinder, pump, valve-body, hoses) can become very hot during operation. Pieces of log may be ejected from the splitter while operating.

  • Page 6: Training

    IMPORTANT SAFETY INSTRUCTIONS 100425 - 34 TON FULL BEAM LOG SPLITTER Training – Gasoline expands or contracts with ambient temperatures. Never fill the gasoline tank to full capacity, as gasoline 1. Read the Operator’s Manual completely before attempting needs room to expand if temperatures rise.

  • Page 7: Preparation

    IMPORTANT SAFETY INSTRUCTIONS 100425 - 34 TON FULL BEAM LOG SPLITTER Preparation 9. When loading a ram-type log splitter, place your hands on the sides of the log, not the ends. Never place your hands 1. Be thoroughly familiar with all controls and with proper use or any part of your body between a log and any part of the of the equipment.

  • Page 8: Safety Symbols

    IMPORTANT SAFETY INSTRUCTIONS 100425 - 34 TON FULL BEAM LOG SPLITTER Safety Symbols These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement.
  • Page 9 IMPORTANT SAFETY INSTRUCTIONS 100425 - 34 TON FULL BEAM LOG SPLITTER SYMBOL MEANING Always keep feet away from the wedge and the ram. Moving parts can crush or cut. Hot Surface. To reduce the risk of injury or damage, avoid contact with any hot surface Open Flame alert.

  • Page 10: Controls And Features

    CONTROLS AND FEATURES 100425 - 34 TON FULL BEAM LOG SPLITTER CONTROLS AND FEATURES Read this operator’s manual before operating your log splitter. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference.

  • Page 11: Assembly

    ASSEMBLY 100425 - 34 TON FULL BEAM LOG SPLITTER ASSEMBLY If your log splitter is already assembled, skip the assembly instructions in this manual. If unassembled, please read and follow these instructions. If you have any questions regarding the assembly of your log splitter, call our Technical Support Team at 1-877-338-0999.

  • Page 12: Install The Fenders

    ASSEMBLY 100425 - 34 TON FULL BEAM LOG SPLITTER 6) Install the Engine and Hoses 4. Block the wheels to prevent the frame from rolling. 5. Pivot the beam to the horizontal position and secure it with NOTICE the lock pin (54) and R-clip (56) through the tow bar.

  • Page 13: Install The Log Catchers

    ASSEMBLY 100425 - 34 TON FULL BEAM LOG SPLITTER 7) Install the Log Catchers 1. Attach large log catcher (23) to side of beam with four M10 × 15 bolts (20), Ø10 lock washers (21), and Ø10 washers (22). 2. Attach small log catcher (25) (opposite side from engine) to the beam with two M10 ×...

  • Page 14: Add Hydraulic Oil

    ASSEMBLY 100425 - 34 TON FULL BEAM LOG SPLITTER 3. Using a funnel, add up to 1.2 qt. (1.1 L) of oil and replace NOTICE oil fill cap/dipstick. DO NOT OVERFILL. Synthetic oil may be used after the 5 hour initial break- 4.

  • Page 15: Add Fuel: Gasoline

    ASSEMBLY 100425 - 34 TON FULL BEAM LOG SPLITTER Add Fuel: Gasoline WARNING 1. Use clean, fresh, regular unleaded gasoline with a DO NOT remove the hydraulic oil fill cap when the engine minimum octane rating of 85 and an ethanol content of is running or hot.

  • Page 16: Before Each Use Inspect The Log Splitter

    ASSEMBLY 100425 - 34 TON FULL BEAM LOG SPLITTER Towing Log Splitter Safety NOTICE 1. Always check local and state regulations regarding the Our engines work well with 10% or less ethanol blend requirements for towing, licensing and lights. gasoline. When using ethanol-gasoline blends there are 2.

  • Page 17: Operation

    OPERATION 100425 - 34 TON FULL BEAM LOG SPLITTER NOTICE NOTICE For Vertical Operation: Keep choke lever in “Choke” position for 2 pulls of the recoil starter. After second pull, move choke lever to the “Run” – Remove the beam lock-pin from the beam bracket position for up to the next 3 pulls of the recoil starter.

  • Page 18: Log Splitter Operation

    OPERATION 100425 - 34 TON FULL BEAM LOG SPLITTER Log Splitter Operation NOTICE 1. ALWAYS wear ear and eye protection, protective clothing The cylinder stroke is designed so the wedge stops and safety gear. approximately 1.5 in. (3.8 cm) from the end plate.

  • Page 19: Maintenance

    MAINTENANCE 100425 - 34 TON FULL BEAM LOG SPLITTER MAINTENANCE Changing the Engine Oil Change oil when the engine is warm. Refer to the oil Make certain that the log splitter is kept clean and stored specification to select the proper grade for your operating properly.

  • Page 20: Cleaning The Air Filter

    MAINTENANCE 100425 - 34 TON FULL BEAM LOG SPLITTER 6. Firmly re-install the plug. NOTICE 7. Attach the spark plug cable to the spark plug. The drain plug is sealed with Teflon tape. Add 2-3 wraps of ® new Teflon tape as needed when replacing the drain plug ®...

  • Page 21: Maintenance Schedule

    STORAGE 100425 - 34 TON FULL BEAM LOG SPLITTER 7. Turn the fuel valve to the “ON” position, and start EVERY 50 HOURS OR EVERY SEASON the engine. Purge the air from the system by extending Clean air filter and retracting the wedge several times until the motion is smooth.

  • Page 22: Engines Stored For Over 30 Days

    STORAGE 100425 - 34 TON FULL BEAM LOG SPLITTER 3. To extend the fuel storage life add a properly formulated fuel stabilizer to the tank. 4. Ensure the fuel valve is in the “OFF” position. Engines Stored for Over 30 Days 1.

  • Page 23: Specifications

    SPECIFICATIONS 100425 - 34 TON FULL BEAM LOG SPLITTER SPECIFICATIONS Hydraulic Oil System Capacity ......... 6.8 gal. (25.7 L) Log Splitter Specifications For year round use in warmer climates (always ABOVE 32˚F/ 0˚C): Ram Force ...

  • Page 24: Parts Diagram

    SPECIFICATIONS 100425 - 34 TON FULL BEAM LOG SPLITTER Parts Diagram...

  • Page 25: Parts List

    SPECIFICATIONS 100425 - 34 TON FULL BEAM LOG SPLITTER Parts List Part Number Description Qty. Part Number Description Qty. GB/T 5783- PMJ37M-01-00 Beam Bolt M10 × 25 2000(M10×25) GB/T 889.1-2000(M12) Lock Nut M12 37 PMJ22J-05-02 Axle Cap GB/T 95-2000(Ø12) Washer Ø12...
  • Page 26 SPECIFICATIONS 100425 - 34 TON FULL BEAM LOG SPLITTER Part Number Description Qty. 72 GB/T 93-1987(Ø8) Lock Washer Ø8 73 ASME B18.2.1 1996 Bolt 5/16"-24 × 1" GB/T 77-2000 Screw M6×10 75 PMJ22G-26 Gear Pump Connector 76 GB/T 1099-1979(3×3) Flat Key 3 × 3 GB/T 5783- Bolt M8 ×...

  • Page 27: Engine Parts Diagram

    SPECIFICATIONS 100425 - 34 TON FULL BEAM LOG SPLITTER Engine Parts Diagram...

  • Page 28: Engine Parts List

    SPECIFICATIONS 100425 - 34 TON FULL BEAM LOG SPLITTER Engine Parts List Part Number Description Qty. Part Number Description Qty. 46 45.110012.00 Bushing, Governor Gear 21.061300.00 Handle, Recoil, Soft 47 47.050200.00 Connecting Rod 1.5789.0608 Flange Bolt M6 × 8 48 46.050005.01...
  • Page 29 SPECIFICATIONS 100425 - 34 TON FULL BEAM LOG SPLITTER Part Number Description Qty. Part Number Description Qty. 90 45.130004.00 Gasket, Air Cleaner 140 1.16674.0510 Flange Bolt M5 × 10 91 2.06.007 141 46.101202.05 Clamp Ø8 × b6 Muffler Protector 92 1.6177.06 Flange Nut , M6 142 46.101300.05...

  • Page 30: Troubleshooting

    TROUBLESHOOTING 100425 - 34 TON FULL BEAM LOG SPLITTER TROUBLESHOOTING Problem Cause Solution No fuel. Add fuel. Engine will not start. Faulty spark plug. Replace spark plug. Unit loaded during start up. Remove load from unit. Fill crankcase to the proper level.
  • Page 31 Warranty Qualifications – Failures due to acts of God and other force majeure events Champion Power Equipment (CPE) will register this warranty upon beyond the manufacturer’s control. receipt of your Warranty Registration Card and a copy of your sales –...
  • Page 32 The United States Environment Protection Agency (U.S. EPA.) and the California Air Resources Board (CARB) Emission Control System Warranty Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air Resources Board (CARB) emission regulations.
  • Page 33 EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1995 and later model year California small off-road engines (for other states, 1997 and later model year engines). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
  • Page 34 You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours.

Table of Contents