Alpine X800D-U Owner's Manual page 113

Radio Antenna Receptacle
ISO/JASO Antenna Adapter (sold separately)
ISO/JASO Antenna Adapter may be required, depending on
the vehicle.
Digital Output Terminal (Optical)
Use when combining fiber optic digital input compatible
products. Be sure to use the Optical Digital Cable
(KWE-610A) (sold separately) only.
iPod VIDEO Input Connector
Input the iPod/iPhone video signal or AUX video/audio
signal.
• Set "AUX3 In Sel." (page 64) to "iPod Video" when an
iPod/iPhone is connected.
• Set "AUX3 In Sel." (page 64) to "AUX3" when AUX video/
audio is input.
MIX Control Lead (Green/White)
Use when an optional External Audio Processor with guide
control input terminal is connected.
• When this lead is connected to PXA-H800, make sure to
turn the ignition key off (ACC OFF) and on (ACC ON)
again or turn the unit power off and on again, after setting
"Navi Mix" from OFF to ON on PXA-H800.
Steering Remote Control Interface Connector
To steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
Beep/NAVI Guide Connector
Output the audio signal of navigation interruption.
When connecting an Audio processor, connect this lead to
the Guide Input terminal with an optional RCA Extension
cable.
Direct CAMERA Input Connector
Use when the optional direct camera is connected.
CAMERA Input RCA Connector (Yellow)
Use when connecting a camera with RCA Output
Connector.
CAN Interface Connector
To CAN Interface box.
Remote Control Output Lead (Brown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
Remote Control Input Lead (Brown)
Connect the external Alpine product to the remote control
output lead.
Speed Sensor Lead (Green/White)
Improper connection of the speed pulse line may cause
important safety features of the vehicle to fail (such as the
brakes or air bags). Such failures may result in an accident
and loss of life. We strongly recommend that the installation
be performed by a trained, authorised Alpine dealer.
Video Input Connector (AUX INPUT) (Yellow)
Input the video.
Audio Input Connectors (AUX INPUT)
RED is right and WHITE is left input the audio.
Video Output Connector (AUX OUTPUT) (Yellow)
Output the video.
Audio Output Connectors (AUX OUTPUT)
RED is right and WHITE is left output the audio.
Rear Output RCA Connectors
It can be used as Rear Output RCA Connectors.
Front Output RCA Connectors
It can be used as Front Output RCA Connectors.
Subwoofer RCA Connectors
RCA Extension Cable (sold separately)
HDMI input Connector
Input HDMI signal, you should prepare an optional Alpine
special HDMI cable.
USB Connector
To USB Memory or iPod/iPhone.
GPS antenna Receptacle
Connect to GPS antenna (included).
Vehicle Display Interface Connector
Outputs Vehicle Display Interface control signals. Connect
this to the optional Vehicle Display Interface box.
For details about connections, consult your nearest Alpine
dealer.
DAB Antenna Connector
To DAB Antenna (sold separately).
MIC Input Connector
To Microphone (Included).
AUX/PRE OUT Connector
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
Reverse Lead (Orange/White)
Connect to the plus side of the car's reverse lamp. This
lamp illuminates when the transmission is shifted into
reverse (R).
With this lead properly wired, the video picture
automatically switches to the rear camera whenever the car
is put into reverse (R).
Parking Brake Lead (Yellow/Blue)
Connect this lead to the power supply side of the parking
brake switch to transmit the parking brake status signals to
the X800D-U/INE-W987D.
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's fuse
box or another unused power source which provides (+)
12V only when the ignition is turned on or in the accessory
position.
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's
battery.
Fuse Holder (15A)
ISO Power Supply Connector
Left Rear (+) Speaker Output Lead (Green)
Left Rear (–) Speaker Output Lead (Green/Black)
113
-EN