Table of Contents
Advertisement
30
2. Flipping Armrest Back and Removing Armrest
a. Depress the release latch and pull arm toward
back of wheelchair.
b. To remove, pull up on armrest. Pin securing arm-
rest will automatically release.
c. To return armrest to operating position, push
armpad down until it locks firmly into place.
G. SWING-AWAY HANGERS AND FOOTRESTS
(60º, 70º, 70ºV OR 90º)
1. Installation (Fig. 5)
a. Place swing-away pivot saddle into the receiver
on front frame tube with the footrest facing out-
ward from the frame. (Fig. 5-A)
b. Rotate the footrest inward until it locks into
place on locking bolt. (Fig. 5-B)
2. Removal
a. To remove footrest, push release latch toward the
frame.
b. Rotate footrest outward and lift.
3. Height Adjustment (Fig. 6)
a. Loosen set screws.
b. Slide footrest extension up or down inside frame
tube to desired height.
c. Tighten set screws.
H. ARTICULATING LEGREST OR ELEVATING LEGREST
(Fig. 7 & 8) (optional)
1. Installation
To install or remove articulating legrest (ALR) or
elevating legrest (ELR) see instructions for
swing-away hangers and footrests.
2. Adjustment
a. To raise legrest, lift to desired position. Legrest
will automatically lock in place.
b. To lower, while seated in chair, press release
lever forward and lower legrest to desired posi-
tion. Legrest will automatically lock in place.
I. FIXED FRONT FOOTRESTS (QUICKIE 2HP ONLY)
1. Adjustment (Fig. 9)
a. Remove mounting bolts on the top of each
extension tube.
b. Make sure the inserts remain in place.
930302 Rev. E
X . S e t - U p & A d j u s t m e n t s
A
B
Figure 5
Figure 6
Articulating
Legrest
Figure 7
Figure 8
X . S e t - U p & A d j u s t m e n t s
c. Slide footrest tube into front frame tube to
desired height.
d. Line up holes and replace the bolt on the outside
through frame, footrest and insert.
e. Follow same procedure on opposite side.
f. Align footrests to desired inward/outward rota-
tional position and tighten firmly.
J. BACKREST
1. Height Adjustment (Fig. 10)
a. Remove the backrest upholstery from the frame.
b. You will see the backrest tube which telescopes
into the frame and is secured by a screw on the
side of the frame.
c. There are holes 1 inch apart that you may choose
from to set the back height.
d. Remove the two backrest bolts from the rear
frame tubes.
e. After selecting the proper height, insert bolt
through frame and backrest tube.
f. Slide the backrest upholstery back over both
backrest tubes.
g. Attach upholstery tab to bolt and tighten nut
and bolt assembly.
h. Insert nylon tie through upholstery grommets.
Tighten and cut off excess nylon tie.
K. ANGLE ADJUSTABLE BACKREST (OPTIONAL)
1. Angle Adjustment (Fig. 11)
a. Loosen button head screws until the eccentric
offset washer moves freely.
b.Adjust backrest to desired angle, aligning eccen-
tric offset washer in slot.
c. Tighten button head screws.
d. Repeat for opposite side.
2. Pivot Point Height Adjustment (Fig. 12)
a. Remove button head screw from the frame.
b. Adjust backrest to obtain desired pivot point
height.
c. Replace and tighten button head screw.
d. Repeat for opposite side.
Elevating
Legrest
31
Figure 9
Figure 10
pivot point
Figure 11
Figure 12
930302 Rev. E
Advertisement
Table of Contents
