Memory Card Problems-Macintosh; Application Problems-Macintosh; When I Tried To Launch Finepixveiwer, The "Quick Time Lib Could Not Be Found" Message Appeared; Print - FujiFilm CX-550 Owner's Manual

6 Using the printer connected to a PC

MEMORY CARD PROBLEMS-Macintosh

I The printer is connected to the Macintosh, but the "Removable disk" icon
is not displayed.
Check
Is the printer power turned on? Turn the printer power on.
Are the printer and Macintosh connected by Check if one end of the USB cable is
a USB cable? connected to the printer and the other end is
connected to the Macintosh.
Is a compatible OS used? Use the printer with Mac OS 8.6 to 9.2.
Is a memory card loaded into the printer? Load a memory card into the printer.
Is the icon for the memory card inserted into Switch the printer off, insert only the
the printer displayed on the screen on the memory card to be used and then switch
top of the printer? the printer back on.
Is Mass Storage Driver enabled? At the Extension Manager, enable
"USB04CB_StorageShim" and "USB04CB
_StorageDriver" and then restart the
Macintosh.
Is the "CONNECTED TO PC IN CARD If the printer is connected as a printer,
READER MODE" message displayed on switch to card reader connection (→P.80).
the printer screen?
I FinePixViewer does not recognize the memory card.
Check
Is the printer turned on? Turn the printer power on.
Are the printer and Macintosh connected by Check if one end of the USB cable is
a USB cable? connected to the printer and the other end is
connected to the Macintosh.
Is the "CONNECTED TO PC IN CARD If the printer is connected as a printer,
READER MODE" message displayed on switch to card reader connection (→P.80).
the printer screen?
Select "View" → "Refresh" from the
Is the window of FinePixViewer updated to
the newest information? FinePixViewer menu.
I Mac OS "Initialize disk" message was displayed.
Check
Do you have a FinePix digital camera? Use a FinePix digital camera to format the
memory card.
Is File Exchange enabled? (When viewing Enable "File Exchange" in Extension
pictures taken with a FinePix digital Manager and then restart the Macintosh.
camera.)
78
Solution
Solution
Solution
Using the printer connected to a PC
I A warning message appears when the memory card was removed or the
USB cable was disconnected from the printer.
Check
This operation may destroy the memory
Was the USB cable unplugged while the
card and data. Drag the drive icon to
printer was mounted as a disk drive?
"Trash" before disconnecting the USB cable
from the printer.
I The Macintosh hangs when the memory card is accessed.
Check
Is the software installed? Install the software (→P.68).

APPLICATION PROBLEMS-Macintosh

I I want to quit Exif Launcher.
Solution
Select "Exif Launcher Setting" in the FinePixViewer "Settings" menu and click "Quit Exif
Launcher immediately".
I I want to stop FinePixViewer from launching automatically.
Solution
Either of the following two methods can be used to prevent FinePixViewer from
launching automatically.
• Change the Exif Launcher settings
q Select "Exif Launcher setting" in the "Settings" menu in FinePixViewer and click "Do
not run Exif Launcher at restart".
w Restart your Macintosh.
✽ To restore the original setting, use the same procedure and select the "Run Exif
Launcher at restart" checkbox. Then restart your Macintosh.
• Remove Exif Launcher.
q Select "Exif Launcher Setting" in the "Settings" menu in FinePixViewer and select
the "Quit Exif Launcher immediately" checkbox.
w Open "System Folder" → "Startup Items" and drag "Exif Launcher" to the Trash.
e Select "Empty Trash..." in the "Special" menu.
✽ To restore the original setting, reinstall the software.
I When I tried to launch FinePixViewer, the "Quick Time Lib could not be
found" message appeared.
Solution
Install QuickTime as described below.
q Load the "Printpix" CD-ROM.
w Open the "English" folder inside the "QuickTime" folder on the CD-ROM.
e Double-click the "Qucick Time Installer" or the "Qucick Time Installer.exe" icon. Then
follow the on-screen instructions.
6
Solution
Solution
79