Electro-Harmonix STEREO MEMORY MAN WITH HAZARAI User Manual page 8

the DELAY knob, the tap time will be erased and the new delay time will be determined by
where the DELAY knob is set.
In LOOP Mode, the DELAY knob turns into a Loop pitch/speed control. Set the DELAY knob
to 50% or 12 o'clock, the loop will playback as it was recorded. Turn the DELAY knob up
from the center and the pitch and speed of the loop will increase up to twice the original
loop's speed. Turn the DELAY knob down from the center and the pitch and speed of the
loop will decrease to half the original speed. The loop pitch/speed changes continuously
without steps so that you can achieve pitches between the notes. Please Note: the
DELAY knob will default to the center position when recording a new loop in LOOP mode
even if the DELAY knob is physically set to a different setting.
REPEATS KNOB
The REPEATS knob is very much like the feedback control that is seen on many other types
of delay units. The function of this knob changes depending on the selected mode. The
following table describes the exact function of the REPEATS knob for each mode:
MODE
ECHO Modes
MULTI TAP Modes
REVERSE ECHO
LOOP
FILTER KNOB
The FILTER knob controls both a Low Pass or High Pass Filter on the delayed signal. When
the knob is set to 50% or 12 o'clock, the frequency response is flat, there will be no
filtering.
The left-hand or counter-clockwise side of the knob controls the amount of Low Pass
filtering. The further you turn the Filter knob down to its minimum counter-clockwise
position, the lower the cutoff frequency of the low pass filter. This means less high
frequency response; a large reduction in treble.
REPEATS KNOB Function
Controls the amount of delay feedback, from 0%
to 99.99%.
Sets the exact number of repeats from 1 to 30.
Controls the amount of delay feedback, from 0%
to 99.99%.
When overdubbing, controls the volume
attenuation of the previously recorded loop. Set to
0%, the previous loop will be erased. Set to 100%
the previous loop will remain at the same volume.
15
The right-hand or clockwise side of the knob controls the amount of High Pass filtering.
The more you turn the Filter knob up to its maximum clockwise position, the higher the
cutoff frequency of the high pass filter. This means less low frequency response; a
reduction in bass.
When the SMMH is set to LOOP mode, the filter knob will filter the loop just as it filters the
echoes. Please Note: the Filter knob will default to the center position when recording a
new loop in LOOP mode even if the Filter knob is physically at a different setting.
DECAY KNOB
The function of the DECAY knob changes depending on the mode selected. The following
table describes the exact function of the DECAY knob for each mode:
MODE
ECHO-3 SEC
ECHO-1 SEC
ECHO-300 mS + MOD
MULTI TAP Modes
REVERSE ECHO
LOOP
DECAY KNOB Function
Varies between discrete echoes (0%) and
smeared reverberant ones.
Varies between discrete echoes (0%) and
smeared reverberant ones.
Controls the depth of the delay time modulation.
0% = no modulation.
Controls the relative volume of each repeat. At 0%
the first repeat will be loudest and the rest of the
repeats inaudible. At 50%, all repeats will be at
equal volume. At 100% the first repeat will be
quietest and the last repeat will be the loudest.
Sets the number of replay voices from 1 (0%) to
25. This is a bit like having a multi tap reverse
echo. Please Note: the intelligent reverse echo
feature works best when the DECAY knob is
turned all the way down to the counter-clockwise
position.
Switches the loop direction from Forward to
Reverse. Turn the DECAY knob to its minimum
position (0%) to Reverse the loop. Turn the
DECAY knob to its maximum position (100%) to
switch back to Forward. After recording a new
loop the DECAY knob will default to playing the
loop forwards.
16