Table of Contents
Advertisement
Quick Links
GB/UK
(R404a)
QUASAR
TECHNICAL SERVICE MANUAL
ICE CUBE MAKERS
MODELS:
QUASAR 20 C
QUASAR 30 C
QUASAR 40 C
QUASAR 40S C
QUASAR 50 C
QUASAR 60 C
QUASAR 90 C
QUASAR 130 C
QUASAR 150 C
MODULARS:
MQ 200
CAREFULLY READ THE INSTRUCTIONS CONTAINED IN THIS MANUAL SINCE THEY
PROVIDE IMPORTANT INFORMATION RELATIVE TO SAFETY DURING INSTALLATION,
USE, AND MAINTENANCE.
EDITION:
NOVEMBER 2001.
COD: QU02MTIN.DOC
104203
104205
104208
104215
1
Advertisement
Table of Contents
Related Manuals for Bartscher QUASAR 20 C
Summary of Contents for Bartscher QUASAR 20 C
- Page 1 GB/UK (R404a) QUASAR TECHNICAL SERVICE MANUAL ICE CUBE MAKERS MODELS: QUASAR 20 C 104203 QUASAR 30 C QUASAR 40 C QUASAR 40S C 104205 QUASAR 50 C QUASAR 60 C 104208 QUASAR 90 C QUASAR 130 C 104215 QUASAR 150 C...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Introduction Warnings..............................3 Description ..............................4 Operating Principles ............................5 Specifications Diagrams of connections and dimensions (undercounter models)..............6 Consumption data, weights, crated dimensions and volumes (undercounter models) ........8 Technical data (undercounter models) ....................... 10 Production Tables ............................11 Delivery & Unpacking Packing .............................. -
Page 3: Warnings
INTRODUCTION Thank you for choosing QUASAR-C ice cube makers. You have purchased one of the most reliable ice-making products on the market today. Carefully read the instructions contained in this manual since they provide important information relative to safety during installation, use, and maintenance. -
Page 4: Description
DESCRIPTION The QUASAR-C ice cubes maker is the result of years of experience in this field and the development of a high technology factory. Main Features • Storage bin made of polyester strengthened with glass fibre or ABS • Stock bin made of high resistance plastic materials •... - Page 5 Once the storage bin is full the pan stops in its downward movement as it touches the cubes, so working the safety stop micro-switch and switching off the machine. Production will start again as soon as the cubes which detained it move or are removed.
- Page 7 Cooling water * HEIGHT Z REPRESENTS MINIMUM MACHINE HEIGHT. IF LEGS ARE PLACED UNDER MACHINE, THEN ADD AN EXTRA 80 MM.* MODEL QUASAR 20 C QUASAR 30 C QUASAR 40 C QUASAR 40S/50 C QUASAR 60 C QUASAR 90 C...
- Page 8 ELECTRICAL CONNECTION STOCK THERMOSTAT WATER INLET...
- Page 9 TECHNICAL DATA MODEL COOLING TOTAL DIMENSIONS GROSS VOLUME WATER PRODUCTION WATER WEIGHT CRATED WEIGHT USAGE WATER USAGE X*Y*Z L/HOUR (1) USAGE L/HOUR (1) (KG) (KG) L/HOUR (1) QUASAR 20C A 490x595x765 0.22 QUASAR 20C W 490x595x765 0.22 QUASAR 30C A 490x595x830 0.24 QUASAR 30C W...
-
Page 10: Production Tables
PRODUCTION TABLES FOR ICE CUBE MAKERS (KG/DAY) QUASAR 20 C QUASAR 30 C 30.5 30.5 19.5 19.5 19.5 19.5 19.5 20.4 20.4 20.5 20.5 30.5 20.5 20.5 30.5 27.5 QUASAR 40 C QUASAR 40S C 30.5 33.5 30.5 33.5 30.5 33.5... - Page 11 QUASAR 90 C QUASAR 130 C 17.5 QUASAR 150 C WATER TEMPERATURE (°C) Water quality= 500 ppm (240 Micromh/cm)
-
Page 12: Delivery & Unpacking
DELIVERY & UNPACKING Upon receipt, thoroughly inspect the packing container. If there appears to be damage to the container contact the shipper immediately. Unpack unit in the presence of delivery personnel noting any damage on the waybill. Packing bears the “Green Point” on all mode ording to the European Directives on management of Packaging and Waste Disposal. -
Page 13: Installation
INSTALLATION The ice cube maker is delivered on a small wooden pallet and is protected with a cardboard box and packaging. Loosen the cardboard box by cutting the straps, then lift vertically. After having removed the packaging, make sure the machine is complete. If in doubt do not use it and go to the distributor who sold it to you. -
Page 14: Water And Drainage
access to condenser and/or water pressure valve, allow sufficient space at front of the machine. Be sure that flooring is firm and even. Water and Drainage Water quality influences ice hardness, flavour, and quality as well as condenser life. Keep in mind the following points: a) WATER IMPURITIES: Major impurities are eliminated by filters provided. -
Page 15: Connecting Unit To Drain
Connecting Unit To Drain (Water Cooled Models) •Drain must be located at least 150mm. below machine level. Drain tube must have an inner diameter of 30mm. with a minimum gradient of 3 cm per metre. Electrical connection • Unit is provided with a 1.5 m cord and Schucko socket. •... -
Page 16: Preliminary Check
IMPORTANT! Supply socket must be properly earthed. Be sure to check standard for country where appliance is going to be installed. OPERATION Preliminary Check a) Is machine levelled? b) Are voltage and frequency of main supply the same as indicated on rating plate? c) Is drainage system functioning? d) Is air circulation and room temperature adequate? (Air-cooled models) ROOM TEMPERATURE... -
Page 17: Water Pressure Control Valve
IMPORTANT! Be sure voltage and frequency of main supply correspond to indicated levels on rating plate. ADVISE THE FINAL USER ON MAINTENANCE PROCEDURES WHICH ARE NOT INCLUDED IN WARRANTY, AS WELL AS THOSE BREAKDOWNS CAUSED BY NEGLECT OF PROPER MAINTENANCE PROCEDURES. ADJUSTMENTS Condenser water valve pressostat (UP TO Q 40S C WATER COOLED) -
Page 18: Pressure Control
Pressure Control Fan pressostat (air condensation) Pressure Control operates on high pressure by starting and/stopping fan. Differential is fixed. (1Kg/cm2 or 14 Psi.) Cut-off pressure must be 16 Kg/cm2 (228 Psi) Low pressure values may cause gearbox malfunction. Pressure values higher than 16 Kg/cm2 may shorten compressor life and diminish ice production. Pressure can be regulated by rotating screw on Pressure Control Valve (clockwise to increase pressure). -
Page 19: Maintenance And Cleaning Instructions
MAINTENANCE AND CLEANING INSTRUCTIONS IMPORTANT! **Maintenance and cleaning procedures as well as problems derived from failing to carry them out are not covered by the warranty. Proper maintenance is essential to obtain favourable ice quality and optimum function of unit. Frequency depends on water quality and characteristics of room where unit is installed. -
Page 20: Water Condenser
MAINTENANCE AND CLEANING PROCEDURES WARNING: Unit should always be disconnected during maintenance/cleaning procedures. Water Condenser 1) Disconnect machine. 2) Close water faucet. 3) Disconnect water entry/exit from condenser. 4) Prepare a solution of 50% phosphoric acid in distilled water. 5) Distribute solution through condenser. (Solution is more effective at 35°-40°C). WARNING! DO NOT USE HYDROCHLORIC ACID Air Condenser... -
Page 21: Inlet Filters
3) Hold agitator paddles so that water pan releases water. 4) Once the water pan returns to its horizontal position again, switch off the machine. Pour 3 litres of water and one half of di-caloid lr) into water pan 5) Allow the solution to work for 20 or 30 minutes, occasionally turning the paddles by hand so that they are also cleaned. -
Page 22: Special Advice Concerning R-404 Refrigerant
Checking for water leaks This must be done whenever maintenance is carried out on the machine: check all water connections, braces, tubes and hoses in order to eliminate leaks and prevent breakages and flooding. Check that the valve closes tightly on models with an automatic cleaning system. SPECIAL ADVICE CONCERNING R-404 REFRIGERANT •... -
Page 23: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSES SOLUTION 1) None of the electrics work. A) The machine is not plugged in. A) Plug the machine. B) The line fuse has blown. B) Replace fuse. C) The current line is wrongly connected in C) Check connections. the junction box. - Page 24 PROBLEM POSSIBLE CAUSES SOLUTION 4) Everything appears to be running A) Freezing system faulty. A) Check system. correctly but no ice made in the (dirty condenser, Presostato o válvula evaporator. entrada agua de condensación averiadas o mal reguladas o falta de refrigerante). B) Hot gas valve faulty (outlet pipe B) Repalce hot gas valve.
- Page 25 PROBLEM POSSIBLE CAUSES SOLUTION 11) Pan does not free cubes or remains in A) Cam motor disconnected or in bad A) y B) Connect or replace cam am intermediary position. condition. motor. ALWAYS change pin and wheel. B) Flexible pin or cam wheel broken. 12) Pan goes up and down constantly.
Need help?
Do you have a question about the QUASAR 20 C and is the answer not in the manual?
Questions and answers