Advertisement
7
Align support mounting bracket with holes in
n
ceiling. Attach support system frame to
ceiling using anchors recommended for your type of
ceiling:
l
Concrete ceiling - use inserts and screws
provided.
l
Wood ceiling - use 4" long wood screws.
9
Press on
n
handle in front of
filters to release filters
from range hood
canopy. Remove filters
and set aside.
l
Plaster or sheet rock ceiling - attach support
Remove the terminal box cover from the
mounting bracket to ceiling joists if possible. If
10
n
range hood. Remove the power supply
screws
ceiling joists are not available, you must build a
supporting structure behind the plaster or sheet
cable knockout using a flat-blade screwdriver.
I
rock.
Attach conduit connector into power supply cable
opening so that conduit connector clamping screws
Make sure the support is connected firmly to
are inside the terminal box.
ceiling.
Personal Injury Hazard
Because of the weight and size of the range
6
Remove the four screws on the upper
n
chimney and disassemble chimney pieces
from support frame.
four set
hood canopy, two or more people are needed to
move and safely install the range hood canopy.
Failure to lift range hood properly could result
in damage to the product or personal injury.
Personal Injury Hazard
Because of the size and weight of this range
hood, the support must be firmly attached to the
ceiling.
l
For plaster or sheet rock ceilings, the support
must be attached to joists. If this is not
possible, you must build a support structure
behind the plaster or sheet rock.
l
Make sure the support is connected firmly to
ceiling.
. Firmly tighten all four set screws before
attaching canopy.
Failure to follow these instructions
could lead to
personal injury or property damage.
8
Determine the height of the canopy. The
n
range hood requires at least 24 inches of
clearance between bottom of range hood canopy
and cooking surface.
The bottom of the canopy will be approximately
9
inches below the bottom of the support system. To
change the canopy height, loosen the four set
screws on the support frame. Adjust support frame
to the desired length and tighten all four set
screws firmly in place before attaching canopy.
located next to
exhaust opening so that there is
approximately
l/4 inch space between bolt head
and canopy. Lift canopy and insert bolts into slots
in support system frame. Tighten bolts to support
system frame and canopy.
Electrical connection
Electrical Shock Hazard
l
Electrical ground is required on this
the appliance is permanently grounded.
. Disconnect power to the junction box before
making the electrical connection.
*This appliance must be connected to a
grounded, metallic, permanent wiring
system, or a grounding connector should be
connected to the grounding terminal or wire
lead on the appliance.
12
n
Make electrical connection:
q
Disconnect power supply.
q
Feed enough power supply cable through
conduit connector to make electrical
connections.
q
Connect the power supply cable to range hood
terminal box through the U.L.-listed conduit
connector.
q
Connect the white wire of the power supply
cable with the white lead in the range hood,
using a twist-on connector; connect the black
wire of the power supply cable with the black
lead in the range hood, using a twist-on
connector.
q
Connect the power supply green (green and
yellow) grounding wire under the green,
grounding screw.
q
Tighten conduit connector screws.
q
Replace the terminal box cover.
Install chimney
sections
13
Attach damper to exhaust opening on
n
top of the canopy using two Phillips-
head screws. Connect ductwork to damper and
seal all connections with duct tape.
chimney
screw
15
Cut upper chimney trim to correct length.
n
Attach trim strips with clips to cover
chimney seam.
14
Position upper chimney section on
section. Check for proper position. Then secure
16
Place filters in canopy opening so rear
n
support system frame.
upper and lower chimney sections to support
n
edge is over flange. Press filters up into
system frame with four screws.
position.
Page 4
Advertisement
