Titan SF16N-9 Safety And Operating Manual
  1. Manuals
  2. Brands
  3. Titan Manuals
  4. Drill
  5. SF16N-9
  6. Safety and operating manual
Titan SF16N-9 Safety And Operating Manual

Titan SF16N-9 Safety And Operating Manual

9 speed bench pillar drill
Hide thumbs
Table of Contents

Advertisement

Quick Links

SAFETY AND OPERATING MANUAL
9 SPEED BENCH PILLAR DRILL
SF16N-9

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SF16N-9 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Titan SF16N-9

Summary of Contents for Titan SF16N-9

  • Page 1 SAFETY AND OPERATING MANUAL 9 SPEED BENCH PILLAR DRILL SF16N-9...
  • Page 2 Congratulations on your purchase of a power tool from Screwfix Direct Ltd. We want you to continue getting the best performance from it so this handbook includes information on safety, handling and care. Please retain this handbook in case you need to refer to any of the information in the future. Your power tool comes with a 12-month guarantee,so should it develop a fault within this period contact Screwfix Direct Ltd on Freephone 0500 41...

  • Page 3: Safety Instructions

    Inspect tool cord periodi- cally and if damaged have them replaced by an authorised service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean and free of oil or grease. 9 SPEED BENCH PILLAR DRILL SF16N-9...
  • Page 4 15. Disconnect tools. When not in use, before servicing and when changing accessories such as blades, bits and cutters, disconnect tools from the power supply. 16. Remove adjusting keys and wrenches. From the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.
  • Page 5 Important note Remove the mains plug from socket before carrying out any adjustment or servicing. Ensure your mains supply voltage is the same as your tool rating plate voltage. 9 SPEED BENCH PILLAR DRILL SF16N-9...
  • Page 6 SYMBOLS Read the manual Warning Wear gloves Wear dust mask,eye & ear protection Conforms to relevant safety standards...
  • Page 7 Fig 1 1. MACHINE BASE 2. PILLAR 3. FIXING SCREW 4. DRILL TABLE 5.CLAMPING SCREW 6. MACHINE HEAD 7. PULLEY COVER 8. MOTOR 9. GRIP KNOBS 10. KEY CHUCK 11. SPINDLE 9 SPEED BENCH PILLAR DRILL SF16N-9...

  • Page 8: Technical Data

    12. MOUNTING HOLES 13. HINGED CHIP GUARD 14. DEPTH SCALE LOCK 15. TIGHTENING SCREW 16. PULLEY COVER LOCK SCREW 17. ON SWITCH 18. OFF SWITCH 19. HEAD LOCK SCREW TECHNICAL DATA 230V~50Hz Voltage: 500W(S2:15mm) Input power : No load speed: 280-2350min Ø3 - Ø16 Chuck capacity:...
  • Page 9 Select suitable length bolts, washers and nuts (not supplied). Use four Fig 3 mounting holes (12) in the base plate to do this. Ensure that the machine is freely accessible for 9 SPEED BENCH PILLAR DRILL SF16N-9...
  • Page 10 operation, adjustment and maintenance. Note: The fixing screws may only be tightened to a point where they do not distort or deform the base plate. Excessive tension can lead to fracture. 4.HINGED CHIP GUARD (See Fig 4) Unscrew the three-recessed head screws (20). Push the transparent cover (22) into the groove of the red mounting frame (23) and fasten it again with the recessed head screws (20).
  • Page 11 Never touch the V-belt when it is rotating. 10.DRILL DEPTH STOP POINT (See Fig 8) Fig 7 The drilling spindle has a swiveling scale ring for setting the drill depth. Only adjust the setting 9 SPEED BENCH PILLAR DRILL SF16N-9...
  • Page 12 when the machine is at a standstill. -Lower the drilling spindle (11) until the tip of the drill bit touches the workpiece. -Slacken the depth scale lock (14) and turn the scale ring (24) forwards until it stops. -Turn the scale ring (24) back to the desired drill depth, then lock this setting into place using the depth scale lock (14).
  • Page 13 Adjust the work table to a suitable height and lock the work table. Move down chuck and tighten the chuck onto the bolt (See fig11 & 12). Turn handle, move up spindle. Chuck will be pulled off. Fig 11&12 9 SPEED BENCH PILLAR DRILL SF16N-9...

  • Page 14: Maintenance

    Drilling Speed Chart (Guide Only) Material to be drilled Steel Cast Iron Hard Metal Aluminium Plastic Wood Drill Drill speed (min 2350 2350 1550 2350 2350 2350 1700 2350 2350 2350 2350 1700 1700 1700 2350 2350 1550 1700 1700 2350 2350 1550...

  • Page 15: Plug Replacement

    The wire that is coloured brown must be connected to the terminal that is marked with the letter L. A 13AMP (BS1363 or BS1363/A) plug must be used and a 5 AMP fuse must be fitted. 9 SPEED BENCH PILLAR DRILL SF16N-9...

  • Page 16: Declaration Of Conformity

    Houndstone Business Park Yeovil BA 22 8RT Declare that the product 9 SPEED BENCH PILLAR DRILL SF16N-9 Complies with the essential health and safety requirements of the following directives: 89/336/EEC, 93/68/EEC–EMC Directive. 73/23/EEC, 93/68/EEC–Low Voltage Directive 98/37/EC–Machinery Directive. Standards and technical specifications referred to:...

Table of Contents