Page 1
SAFETY AND OPERATING MANUAL Original instructions 10.8V DRILL DRIVER TTP451DDH...
Page 2
Congratulations on your purchase of a power tool from Titan Power Tools (UK) Ltd. We want you to continue getting the best performance from it so this handbook includes information on safety, handling and care. Please retain this handbook in case you need to refer to any of the information in the future.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. 10.8V DRILL DRIVER TTP451DDH...
Page 4
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 10.8V DRILL DRIVER TTP451DDH...
Page 5
4. If the charger supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 5. Never charge damaged batteries as these can short circuit and over heat. 10.8V DRILL DRIVER TTP451DDH...
Page 6
18. When the battery is worn out, insulate the terminals with adhesive tape or similar materials before disposal. 19. Do not dispose of batteries in fire, or with household waste. Return exhausted batteries to your local collection or recycling point. 10.8V DRILL DRIVER TTP451DDH...
Page 7
The use of the correct accessory for the tool and ensuring it is sharp and in good condition. The tightness of the grip on the handles. And the tool is being used as intended by its design and these instructions. 10.8V DRILL DRIVER TTP451DDH...
Fast intervention can prevent serious injury and damage to property. 2.Switch off and disconnect from the power supply if there is any malfunction. Have the product checked by a qualified specialist and repaired, if necessary, before you put it into operation again. 10.8V DRILL DRIVER TTP451DDH...
T o reduce the risk of injury, user must read instruction manual Warning Waer ear protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. Li-Ion 10.8V DRILL DRIVER TTP451DDH...
Page 10
30 min charging time 30min Before charging, read the instructions This symbol indicates that this battery contains lithium. This battery shall be recycled. Safety fuse T3,15A yyWxx Manufacturing date code: Year of manufacturing (20yy) and week of manufacturing (Wxx); 10.8V DRILL DRIVER TTP451DDH...
Page 11
10 Charging indicator 2 Torque adjustment ring 3 Gear control 4 Forward /lock/ reverse rotation 5 ON/OFF switch with variable speed control 6 Battery pack 7 Battery pack release button 8 LED light 9 Charger 10.8V DRILL DRIVER TTP451DDH...
NOISE DATA A weighted sound pressure 65.4dB(A) / K : 3dB(A) A weighted sound power 76.4dB(A) / K : 3dB(A) Wear ear protection when sound pressure is over 80dB ACCESSORIES 1.5Ah Li-Ion battery pack 30 minutes charger 10.8V DRILL DRIVER TTP451DDH...
“clicks” Fig. 2 into position. Make sure the release button on battery pack snaps in place and the battery pack is secured in tool before beginning operation. 10.8V DRILL DRIVER TTP451DDH...
Ensure the bit is in the centre of the chuck jaws. Finally, firmly rotate the front chuck section in the opposite directions. Your bit is now clamped in the chuck. 10.8V DRILL DRIVER TTP451DDH...
To turn on the light simply press the on/off switch. When you release the on/off switch, the light will be off. WARNING: The light is a focussed beam and should never be pointed directly into the eyes of people or animal. 10.8V DRILL DRIVER TTP451DDH...
If you charge a second battery pack immediately after the first then the charger can be overheated. Always allow at least 15 minutes rest between battery pack charging. 10.8V DRILL DRIVER TTP451DDH...
Page 17
Do not re-charge your battery pack below 0°C and above 50°C as this will affect performance. 10.8V DRILL DRIVER TTP451DDH...
Do not attempt to open or remove any of the components. 10.8V DRILL DRIVER TTP451DDH...
Page 19
L. A 13 AMP (BS1363 or BS1363/A) plug must be used and a 3 AMP fuse must be fitted. 3AMP BLUE FUSE N (NEUTRAL) BROWN L (LIVE) OUTER SLEEVE CABLE GRIP 10.8V DRILL DRIVER TTP451DDH...