Related Manuals for Alpha Communications VPD-5000
Summary of Contents for Alpha Communications VPD-5000
- Page 1 VDP-5000 Alpha Communications® 42 Central Drive - Farmingdale NY 11735-1202 Toll Free. 1-800-666-4800 In Metro NY. 631-777-5500 Fax: 631-777-5599 Email: info@alpha-comm.com Web. www.alpha-comm.com AWD080 Rev.2 (06/04)
- Page 2 WARNING To prevent injury, the following safety precautions should be observed in the installation, use and servicing of the set. CAUTION RISK OF ELECTRIC SHOCKS DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated...
- Page 3 SAFEGUARDS 1. Read Instructions polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try All the safety and operating instructions should be read before the unit is operated. reversing the plug.
-
Page 4: Table Of Contents
Important Notice Always use discretion when installing video and audio surveillance equipment especially when there is perceived privacy, or an expectation of privacy. Inquire regarding federal, state and/or local regulations applicable to the lawful installation of video and/or audio recording or surveillance equipment. -
Page 5: Unit & Components
UNIT & COMPONENTS UNIT & COMPONENTS Camera (VDP-C5F) Monitor (4 B/W C.R.T) Side & Bottom panel Side & Bottom panel Note : If the camera lens angle requires adjustment, simply position the lever of angle adjustment and then tighten the screw on it with a philip screwdriver before installation. -
Page 6: Parts Check-List
PARTS CHECK-LIST The parts shown below are provided by the manufacturer and are enclosed in the box. Handset Main Mounting Bracket OPERATIONS Cable Monitor Mounting Screw Mounting Screws Adaptor User Manual (3 8 mm) (4 20 mm) Cameras Optional surface mount camera VDP-C5F VDP-C5S Flush Box... -
Page 7: Installation 1
INSTALLATION INSTALLATION Installation Camera < Figure 2 > < Figure 3 > < Figure 4 > < Figure 5 > 1. It is recommended to mount the flush box of the camera into the wall. 1. After determining the mounting locations for both the outside camera and inside monitor, it is recommended to mount the camera and monitor to the height of an 2. -
Page 8: Wiring Diagram
WIRING DIAGRAM 1 Monitor & 1 Camera Wiring is not supplied with your Video Doorphone System. Use only AWG #22 wire(0.65mm) / TIV wire(0.80mm) and follow the appropriate wiring diagrams exactly for optimum system performance and safety. < Figure 6 > 1 Monitor &... -
Page 9: Operation 1
OPERATION Turn the power switch to ON to be in standby mode. Communicating Function 1. A visitor presses the “Call” button on the outside camera unit. The monitor will sound a “chime” tone two times to announce that a visitor is at the door. -
Page 10: Trouble Shooting
TROUBLE SHOOTING SPECIFICATIONS Trouble Shooting Guide Main unit Monitor (VDP-M5F) If a problem persists after trying the remedies suggested below, contact your local Remark Specifications dealer or our technical support or sales department Voltage Requirements DC 12V Power Consumption Maximum 8.5W, Stand by 1.0W Unit totally dead (Power Lamp OFF) Monitor Screen B&W Flat 4 Flat type C.R.T... -
Page 11: Dc Power
DC POWER Surface Mount Camera (Option) Input Remark Specifications Voltage Requirements 100 to 250VAC -10%, +6% Power Source DC 12V (Supplied from Monitor) Line Frequency 47- 63Hz Power Consumption DC 12V, 0.15A Current 0.5A Max. at 110 VAC input Internal primary current fuse Display Output 1Vp-p/75, Composite EIA / CCIR Protection... - Page 12 Memo...