Page 1
WINCE 6.0 Car Navigation Box CS9320 User Manual CS9320 is Wonde Proud's new era for GPS+GLONASS dual‐mode navigation. Following past model's stability and universal compatibility, we developed CS9320 as an advanced new model. GPS+GLONASS dual‐mode for more accurate positioning, HDMI output for entertainment, dual video display providing sound drive/passenger service. Supported with Wonde Proud plug & play GPS/multimedia interface, CS9320 is going to have your driving experience enjoyable. support@car-solutions.com www.car-solutions.com...
Page 2
Thank you for purchasing CS9320 Navigation Box. Before you start operating navigation, please refer to the following tips. 1. Optional function would work once you connect external device. 2. Firmware updating should be finished within several minutes. 3. Remember to change the resolution value after changing the panel setting so that both of them will work correctly. 4. If you change setting of resolution or panel inappropriately, error of display or touching control would take place. Under the circumstances, please contact your distributor or agency and get a file named LCD93.inf. Put this file into your SD card and restart the navigation box. support@car-solutions.com www.car-solutions.com...
Page 3
Main Menu I _______________________________________________ 3 Adjusting (RGB Adjust / CVBS Adjust / HDMI Adjust) ______________ 5 Panel (select correct touching code for your panel)_______________11 Resolution Setting for Correct Image Display ___________________ 11 Calibration for Correct Touch Response _______________________ 14 System: Auto Run Navigation On/Off _________________________ 14 System: change the map’s path______________________________ 15 System: firmware update __________________________________ 18 System: Update Logo (Change your Start‐up Picture)_____________ 20 System: NAVI MUTE ON/OFF 22 System: Shortcut to Menu On/Off ___________________________ 22 ...
Page 4
Info.: check OS and firmware version of CS9320________________32 Installation _______________________________________________ 33 Pin Definition_____________________________________________36 Reset CS9320 with LCD93.INF______________________________37 Main Menu I Map access HB, HS, VB adjusting Select Panel model support@car-solutions.com www.car-solutions.com...
Page 5
Back to last page Select System resolution Touching calibration System setting To next page support@car-solutions.com www.car-solutions.com...
Page 7
1. RGB Adjust: H‐Balance—horizontal Balance of RGB image H‐Size—horizontal Size of RGB image V‐Balance—Vertical Balance of RGB image support@car-solutions.com www.car-solutions.com...
Page 8
Brightness—brightness of RGB image H – Shift‐‐‐‐RGB image horizontal moving H – Scale‐‐‐‐RGB image zoom in and zoom out If the image is not in the middle, and you can’t see the edge, please make an adjusting until you can see the complete image. P.S.: When you adjusted to a wrong value, you might lost image, but as long as you didn’t click “Save,” please restart CS9320 and you can reset the values. 2. CVBS Adjust Please select correct CVBS protocol according to your monitor. support@car-solutions.com www.car-solutions.com...
Page 9
Width‐‐‐width of CVBS image Height‐‐‐height of CVBS image Brightness‐‐‐brightness of CVBS image Contrast‐‐‐color contrast of CVBS image If the image is not in the middle, and you can’t see the edge, please make an adjusting until you can see the complete image. P.S.: When you adjusted to a wrong value, you might lost image, but as long as you didn’t click “Save,” please restart CS9320 and you can reset the values. 3. HDMI Adjust Please select the right option for HDMI setting support@car-solutions.com www.car-solutions.com...
Page 10
P.S.: When you adjusted to a wrong value, you might lost image, but as long as you didn’t click “Save,” please restart CS9320 and you can reset the values. support@car-solutions.com www.car-solutions.com...
Page 11
Panel, input code: 7777 Select the right panel model to match your car monitor in order to enable touching control and successful display. support@car-solutions.com www.car-solutions.com...
Page 12
Resolution, input code: 7777 level, Select the correct resolution, and click “OK”: support@car-solutions.com www.car-solutions.com...
Page 13
level, select the matched resolution with your panel, and click “OK” again, then the right setting is saved. When your Kenwood panel’s resolution is “640x420”, Please select “640x480” and use map of resolution 640x480 support@car-solutions.com www.car-solutions.com...
Page 15
Touch “+” to ensure correct icon response. Setting page of System 1. “Auto Run Navi ON” means the system would enter into the map software directly, otherwise it won’t. support@car-solutions.com www.car-solutions.com...
Page 16
2. Steps of changing the map’s path: First of all, please put the map’s file into SD card, and insert SD card to CS9320, then, click icon “System” “Navi Path” Browse, and select “SDMMC Disk” support@car-solutions.com www.car-solutions.com...
Page 17
Enter correct folders and continually find “.exe” file support@car-solutions.com www.car-solutions.com...
Page 18
Complete setting your map’s path Save Note: the pre‐setting of map’s path is: \SDMMC DISK\WP_NAVI\NAVI\WP_NAVI.EXE By above steps, you can change map’s path for your own CS9320. support@car-solutions.com www.car-solutions.com...
Page 19
3. Steps of Firmware Updating: Put the appropriate file to SD card and plug SD card into the device, then press the button of “Update Firmware” and wait for the system to finish Firmware updating. (1) Format SD card. (2) Copy UPD file to SD card first. (3) Copy the others to SD card. (4) Insert SD card to the navi‐box and then plug the power line. (5) If the RGB monitor match the setting of the navi‐box, you will see the update process on the RGB monitor, if there’s nothing can be seen, you can check LED that will light after 2 seconds since plugging the power line and you need to wait around 3 minutes to finish the process (please do not power off while updating within 3 minutes). (6) If you use CVBS/HDMI‐in monitor, navi‐box will not show any message while updating process, you need to wait around 3 minutes (Please do not power off while updating within 3 minutes), after finishing the update process, navi‐box will show the main menu in the CVBS/HDMI‐in monitor. (7) After updating process, navi‐box will auto boot. When you see the main menu appear, you need to eject SD card then un‐plug the power line and plug the power line again for complete OS updating process. Note: It will not show anything in booting step for CVBS / HDMI out. Click Here support@car-solutions.com www.car-solutions.com...
Page 20
Click here to update file Search from SDMMC Disk Look for a file of “.bin” type support@car-solutions.com www.car-solutions.com...
Click “UPDATE;” and wait until it’s counted “100” and you see “Updated Successful.” 4. Update logo: “Update Logo” can help you change the start‐up picture. To change start‐up picture, please follow the steps: a. Prepare 7 pictures, 24bit bmp file, containing following resolutio n: 320x240, 400x234, 480x234, 480x272, 640x480, 800x480, 640x240. b. The file names of 7 pictures have to be like following, consistent with the resolution: logo320240.bmp logo400234.bmp logo480234.bmp support@car-solutions.com www.car-solutions.com...
Page 22
logo480272.bmp logo640480.bmp logo800480.bmp logo640240.bmp c. Put the 7 pictures you prepared into SD card root, insert CS9320, and click “UPDATE,” then your start‐up picture is updated. Please restart CS9320 to see. Navi Mute ON / OFF All other sound will mu te when navigation talks. support@car-solutions.com www.car-solutions.com...
Page 23
6. Shortcut to Menu On: If “Shortcut to Menu On” is selected, it means when CS9320 is navigating in the map, you can access main menu with pressing right bottom corner of your touch panel for more than 2 seconds. And when you access main menu, navigating will keep going. 7. RF Reset Reset RF pairing function support@car-solutions.com www.car-solutions.com...
Page 24
8. Resolution Change Confirm ON/OFF 9. Glonass Filter ON/OFF Choose signal by GPS or GLONASS support@car-solutions.com www.car-solutions.com...
Page 25
Main Menu II support@car-solutions.com www.car-solutions.com...
Page 26
Open Windows Explorer Extra video input, or Digital TV access (Optional) Rear Camera access (Optional) Back to last page 3G device (Optional) Setting page of Wireless (Optional) Select Browser to surf the Internet (Optional) To next page support@car-solutions.com www.car-solutions.com...
Page 27
3G device (Optional) Use Input Panel to key in the data Wireless Click Here to Add New W ireless network support@car-solutions.com www.car-solutions.com...
Page 28
Use Input Panel to key in the data and select “OK” to save After finishing the setting of Wireless Network, please select the network you need and “Connect.” support@car-solutions.com www.car-solutions.com...
Page 29
IE Select the browser with which you want to surf the Internet. Main Menu III support@car-solutions.com www.car-solutions.com...
Page 30
Check System Time Cursor Hide Choose Power Mode for system Back to last page Choose UART connecting device for system Check information of system To next page support@car-solutions.com www.car-solutions.com...
Page 31
Time Select correct zone, date, and time Cursor Select “Cursor Show” if you would like cursor to be visible all the time. Select “Cursor hide” if you would like cursor to be invisible forever. After “Cursor hide” is support@car-solutions.com selected, you need a “LCD92.INF”...
Page 32
Press “+” and “-” to set up the seconds you want cursor Power Mode to disappear when there is Select Power Mode for device: no operation. Reboot Mode: GPS back up only; once you restart CS9320, GPS re‐positions, and navigation restarts. Suspend 1 Mode: When you restart CS9320, navigation starts at wh ere you turn off CS9320. P.S.: Suspend 1 Mode needs lots of power consumption when you turn off CS9320; thus, it could lead car battery to run out of power if you leave your car not started for too long. support@car-solutions.com www.car-solutions.com...
Page 33
Suspend 2 Mode: TBD Related Time Setting: TBD UART Select UART connecting device and save. If you only have 1 device for Uart port, and didn’t purchase “2‐port Uart cable (optional),” please select your device on “UART A.” If you have purchased “2‐port Uart cable,” please select correct device according which port (A or B) you connected to the device. Info. Check Firmware and OS version. support@car-solutions.com www.car-solutions.com...
Installation As long as your monitor or car in‐dash have RGB/CVBS input for external navigation, you will be able to integrate CS9320 navigation box. The following chart s are guides for CS9320’ s installation. support@car-solutions.com www.car-solutions.com...
Page 38
4pin-touch port (resistive touch): Cap touch port (capacitive touch): support@car-solutions.com www.car-solutions.com...
Page 39
9-pin RGB: 8-pin data support@car-solutions.com www.car-solutions.com...
Page 40
6-pin UART: How to install the navigation box to your vehicle: 1. Plug the Map SD card into the navigation box. 2. Connect port “DC IN” (Navigation Box) with power cable; on power cable, ACC to Car ACC, BAT to Car battery, GND to ground, and MUTE to mute wire from monitor. Note: please DON’T connect BAT and ACC together. 3. Connect GPS antenna, and put it where you can receive GPS signal well. 4. Link RGB (9 pin) cable, Data (8 pin) or AV cable to your monitor and use USB mouse to select the right panel. Note: on RGB cable, you could see PIN 1 and PIN 2, support@car-solutions.com www.car-solutions.com...
Page 41
PIN 1=external navigation mute PIN 2=rear camera trigger 5. If you have touch screen, connect 4‐pin touch cable to the 4‐pin hole on the side of navigation box. Note: if you couldn’t see any image after you link RGB cable to the monitor, please proceed the following steps: 1. Make sure that you connect AV cable well and USB mouse to adjust panel setting and try again. LCD93.inf.” 2. Enter your SD card with PC and find a file called, “ Then, key in the right “resolution” and “panel,” save and insert SD card to CS9320 again. Reset CS9320 with LCD93.INF: When wrong resolution is selected, the image will disappear or become unstable. Under this situation, please follow below steps to reset CS9320: 1. Get the file, “LCD93.inf” from your distributor 2. put the file into an empty 2G SanDisk SD card 3. insert the SD card into CS9320, and restart CS9320 3 to 5 times. Note: If there is nothing appearing from monitor, please wait about 30 seconds and power off/on CS9320 again. 4. Then you should have stable image again, please take out SD card and delete the file. Note: As long as the “LCD93.inf” file existed in SD card with CS9320, it will erase the previous resolution setting. LCD93.inf file: support@car-solutions.com www.car-solutions.com...
Page 42
Select the correct res olution and save. support@car-solutions.com www.car-solutions.com...