Clip Continuous Recording (Udf Only) - Sony PMW-200 Operating Instructions Manual

"HQ 1280×720/23.98P" (in UDF HD Mode) or "SP
1440×1080/23.98P" (in FAT HD Mode).
• Frame Recording mode cannot be used when the items
"DVCAM" or "HDV" are set for "SDI/HDMI/i.LINK
I/O Select" (page 89) in the VIDEO SET menu, and
the video format of "Format" in "System" (page 98) in
the OTHERS menu is set to other than "HQ mode/
23.98P."
Preparatory settings
Before starting Frame Recording, make the
necessary settings in the CAMERA SET menu
(page 83) in advance.
Performing Frame Recording
When the preparatory settings are completed, you
can start recording.
1
Press the REC START/STOP button.
When the number of frames you specified
with the menu are recorded, the camcorder
automatically enters FRM STBY (Frame Rec
Standby) status.
2
Press the REC START/STOP button
again.
Each time you press the REC START/STOP
button, the camcorder records the specified
number of frames then enters FRM STBY
status.
Notes
• Recording cannot be stopped until the specified
number of frames are recorded. If the power switch is
set to OFF during recording, the power is only shut off
after the specified number of frames are recorded.
• The Rec Review function cannot be used while
recording in Frame Rec mode is in progress.
• You cannot change the "Number of Frames" setting
while recording in Frame Rec mode is in progress. To
change it, pause the recording.
• The timecode is recorded in Rec Run mode (page 93)
during Frame Recording.
• Some extra frames may be recorded if you stop
recording or switch the card slot while recording is
paused in Frame Rec mode.
• "Setting" for "Frame Rec" is automatically set to "Off"
when you set the power switch to OFF, while the
"Number of Frames" setting is maintained.
48 Useful Functions
Clip Continuous Recording (UDF
Only)
Clips are normally created individually for each
time you start and stop recording, but you can also
continue recording to a single clip regardless of
the number of times you start and stop recording
by using the Clip Continuous Recording function,
which will add recordings to the same clip until
the function is disabled or turned off.
This is convenient for when you do not want to
create a large number of short clips, or when you
do not want to be restricted by a maximum
number of clips.
A recording start mark is added to each point at
which you resume recording, making it easy to
search for each point.
Preparatory settings
Before starting Clip Continuous Recording, make
the necessary settings to "Clip Cont. Rec" (page
83) in the CAMERA SET menu in advance.
When you set "Setting" to "On," the Clip
Continuous Recording function is enabled, and
"CONT" appears on the screen (page 19).
You can also assign "Clip Cont. Rec" to an
assignable button (page 47), and set "Setting" to
"On"/"Off" by pressing the button.
Notes
• Clip Continuous Recording cannot be set to "On"
simultaneously with Picture Cache Recording, Interval
Recording, Frame Recording, or Slow & Quick
Motion. When you set Clip Continuous Recording to
"On," these other functions are forcibly set to "Off."
• Clip Continuous Recording cannot be used while
recording.
• This function cannot be used with FAT.
Performing Clip Continuous Recording
When the preparatory settings are completed, you
can start recording.
Press the REC START/STOP button.
When recording starts, the "CONT" indication on
the screen changes to "zREC" (with z in red).
Notes
• If you remove the SxS memory card or the battery
while recording or standing by to record (the "CONT"
indication appears), the SxS memory card must be
restored. Only remove the SxS memory card after Clip
Continuous Recording is complete. If "CONT" is