Related Manuals for BNF Blade Nano CPX
Summary of Contents for BNF Blade Nano CPX
- Page 1 Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di istruzioni...
-
Page 2: Safety Precautions And Warnings
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product. Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury. -
Page 3: Table Of Contents
fi rst fl ight, and every one after it, is the best it can be. BLH3300 BLH3380 *Transmitter not included with BNF Version Table of Contents Charging Warnings ............4 Low Voltage Cutoff (LVC) ..........10 Battery Charging ...............4... -
Page 4: Charging Warnings
Charging Warnings The Battery Charger (EFLC1000) included with your • Always charge batteries away from helicopter has been designed to safely charge the Li-Po fl ammable materials. battery. • Always inspect the battery before charging • Always disconnect the battery after charging, and let CAUTION: All instructions and warnings must be the charger cool between charges. -
Page 5: As3X Flybarless Helicopter Technology
• Install the fully charged fl ight battery in the helicopter ❏ Fly the model • Program your computer transmitter (BNF ONLY) ❏ Land the model • Test the controls ❏ Unplug the fl ight battery from the 3-in-1 control unit •... - Page 6 ® Programming Your Transmitter contd. DX7/DX7se FUNCTION MODE SYSTEM LIST Model Type D/R & EXP Thro Curve NORM 100% HELI 0-AILE 100% ST-1 100% INH INH% 100% 0-ELEV 100% ST-2 100% 100% 100% 100% 100% Swash Type HOLD 0-RUDD 100% 1 Servo 90 1-AILE Pitc Curve...
-
Page 7: Transmitter And Receiver Binding
NOTICE: Use the Non-Computer Radio binding instructions if you are using a DX4e or DX5e transmitter with the Nano CP X BNF. Binding Procedure for Computer Radios: 1. Disconnect the fl ight battery from the helicopter. -
Page 8: Understanding The Primary Flight Controls
Understanding the Primary Flight Controls If you are not familiar with the controls of your Nano CP X, take a few minutes to familiarize yourself with them before attempting your fi rst fl ight. Throttle Mode 1 Mode 2 (model viewed from left) Descend Ascend Throttle up... -
Page 9: Throttle Hold
Throttle Hold Throttle hold is used to turn off the helicopter motors if the helicopter is out of control, in danger of crashing or both. Activate throttle hold anytime the helicopter is in danger to reduce the chance of damaging the helicopter in a crash. -
Page 10: Installing The Flight Battery
Installing the Flight Battery 1. Lower the throttle and throttle trim to the lowest settings. 2. Power on the transmitter. 3. Install the fl ight battery in the battery holder. Connect the battery cable to the 3-in-1 control unit. NOTICE: Do not allow the helicopter to move until the blue LED on the 3-in-1 control unit is solid. -
Page 11: Troubleshooting Guide
Troubleshooting Guide Problem Possible Cause Solution Reset controls with throttle stick and throttle Throttle at high position trim at center or lowest setting Helicopter will not Switches not in normal position Set flight mode to OFF/0 and exit throttle hold. initialize Pitch or throttle servo reversing im- Reset servo reversing... -
Page 12: Exploded View And Parts Listings
Exploded View and Parts Listings... -
Page 13: Optional Parts
Optional Parts Part # Description BLH3318A Blue Canopy Set: Nano CP X BLH3320A Blue Vertical Fin: Nano CP X EFLC1004 Celectra 4 port charger EFLC1005 AC to 6VDC 1.5-Amp Power Supply DX6i Transmitter DX7S Transmitter DX8 Transmitter DX18 Transmitter Part # Description Feathering Spindle w/O-Rings &... -
Page 14: Limited Warranty
Limited Warranty What this Warranty Covers to better answer your questions and service you in the event Horizon Hobby, Inc., (Horizon) warrants to the original pur- that you may need any assistance. For questions or assis- chaser that the product purchased (the “Product”) will be tance, please visit our website at www.horizonhobby.com, free from defects in materials and workmanship at the date submit a Product Support Inquiry, or call 877.504.0233 toll... -
Page 15: Warranty And Service Contact Information
Warranty and Service Contact Information Country of Horizon Hobby Address Phone Number/Email Address Purchase 4105 Fieldstone Rd 877-504-0233 Horizon Service Center Champaign, Illinois Online Repair Request: (Electronics and engines) 61822 USA visit www.horizonhobby.com/service United States of America 4105 Fieldstone Rd Horizon Product Support 877-504-0233 Champaign, Illinois... -
Page 16: Fcc Information
FCC Information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 17 Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH2012081002 Product(s): Nano CP X BNF Item Number(s): BLH3380 Equipment class: The object of declaration described above is in conformity with the requirements of the specifi cations listed below, following the provisions of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive 2006/95/EC: EN 301 489-1 V1.7.1: 2006...
- Page 18 ©2012 Horizon Hobby, Inc Blade, E-fl ite, AS3X, Celectra, Bind-N-Fly, DSM2, DSMX, and ModelMatch are trademarks or registered trademarks of Horizon Hobby, Inc. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. D578,146.
Need help?
Do you have a question about the Blade Nano CPX and is the answer not in the manual?
Questions and answers