NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product. Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
Charger – 2-Cell 7.4V DC Li-Po Charger with AC adapter Included Transmitter – Requires a DSM2 Sold Separately ® ® /DSMX Transmitter, DX6i or higher Blade mCP X BL Specifi cations Length Main Rotor Diameter 9.85 in (250mm) 10.35 in (263mm) Height Tail Rotor Diameter 3.95 in (100mm) 1.60 in (40mm)
Charging Warnings The Battery Charger (EFLUC1007) included with your • Always charge batteries away from fl ammable helicopter has been designed to safely charge the Li-Po materials. battery. • Always inspect the battery before charging. • Always disconnect the battery after charging, and let CAUTION: All instructions and warnings must be the charger cool between charges.
E-fl ite 2S 7.4 V 200mAh 30C Li-Po Battery Pack (EFLB2002S30) The Blade mCP X BL 2S Li-Po battery features an EFL2 connector that allows you to safely charge your battery pack when used with the included Li-Po charger and charge adapter. The included fl ight battery is safe to charge up to 3C (0.6 Amp).
® Programming Your Transmitter Program your transmitter before attempting to bind or fl y the helicopter. Transmitter programming values are shown below for the Spektrum™ DX6i, DX7/DX7se, DX7s, DX8, and DX18. The fi les for models using Spektrum transmitters with AirWare™ software are also available for download online in the Spektrum Community. NOTICE: When using a Futaba ®...
Understanding the Primary Flight Controls If you are not familiar with the controls of your mCP X BL, take a few minutes to familiarize yourself before attempting your fi rst fl ight. Throttle Ascend Descend Throttle up Throttle down (Positive collective pitch) (Negative collective pitch) Rudder Nose Yaws Left...
Choosing a Location The Blade mCP X BL can be fl own outdoors or in larger indoor spaces like a gymnasium. Before choosing a loca- tion, it’s a good idea to familiarize yourself with any local ordinances that might affect the operation of RC aircraft.
Throttle Hold Throttle hold is used to turn off the helicopter motors if the helicopter is out of control, in danger of crashing or both. Activate throttle hold anytime the helicopter is in danger to reduce the chance of damaging the helicopter in a crash.
Troubleshooting Guide Problem Possible Cause Solution Reset controls with throttle stick and throttle Throttle at high position trim at center or lowest setting Helicopter will not Set flight mode to OFF/0 and exit throttle Switches not in normal position initialize hold.
Exploded View and Parts Listings Part # Description Part # Description Flybarless BL 3n1 Control I BLH3910 Stock Tail Fin: mCP X BL A BLH3901 Unit,RX/ESC/Gyros: mCP X BL Feathering Spindle w/O- Tail Boom Assembly wRotor/ J BLH3911 Rings,Bushings,& Hdwe:mCP B BLH3902 Mount: mCP X BL X BL...
Limited Warranty What this Warranty Covers contact your local distributor or Horizon directly. This will Horizon Hobby, Inc., (Horizon) warrants to the original pur- enable Horizon to better answer your questions and service chaser that the product purchased (the “Product”) will be you in the event that you may need any assistance.
Warranty and Service Contact Information Country of Horizon Hobby Address Phone Number/Email Address Purchase 877-504-0233 Horizon Service Center 4105 Fieldstone Rd Online Repair Request: (Electronics and en- Champaign, Illinois visit www.horizonhobby.com/ gines) 61822 USA United States of service America 4105 Fieldstone Rd Horizon Product Support 877-504-0233 Champaign, Illinois...
Compliance Information for the European Union Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH2012092801 Product(s): BLH mCP X BL BNF Item Number(s): BLH3980 Equipment class: The object of declaration described above is in conformity with the requirements of the specifi cations listed below, following the provisions of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive...
Page 17
HINWEIS Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby, Inc. jederzeit geändert werden. Die aktuelle Produktliteratur fi nden Sie auf horizonhobby.com unter der Registerkarte „Support“ für das betreffende Produkt. Spezielle Bedeutungen Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe Gefahren- risiken beim Betrieb dieses Produkts hinzuweisen: HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe oder keine Gefahr von Verletzungen ergeben.
Page 18
Leitfaden zur Problemlösung der Ihnen hilft das meiste aus dem Hubschrauber heraus zu holen und Sicherheit für Sie und andere zu gewährleisten. Blade mCP X BL Features Bind-N-Fly Rumpf – Blade mCP X BL Inklusive Haupt- und Heckmotor - Brushless Eingebaut On-board Elektronik - 3 in 1 Empfänger/Servo/Mischer/Regler/Kreisel...
Wenn Sie wiederholt bis zur Niederspannungsabschaltung fl iegen, wird der Akku beschädigt. AS3X Flybarless Technologie Der Blade mCP X BL ist mit der AS3X Flybarlesstechnologie ausgestattet. Das AS3X System kombiniert eine 3 Ach- sen Gyro Stabilisierung mit einem Paddelstangen-losen Flybarless Rotor Kopf, der für geringeren Luftwiederstand und weniger Bauteilen eine höhere Leistung bietet.
Celectra 2-Cell 7.4V DC Li-Po Ladegerät (EFLUC1007) 2S 7.4 V 200mAh 35C Li-Po Akku Pack (E-fl ite EFLB2002S30) Der Akku des Blade mCP X BL 2SLiPo Akku ist mit einem EFL2 Anschluß ausgestattet der es zusammen mit dem im Lieferumfang enthaltenen Ladegerät und dem Lade- adapter ermöglicht den Akku sicher aufzuladen.
® Programmieren Ihres Senders Bitte programmieren Sie ihren Sender bevor Sie ihn an den Hubschrauber binden und fl iegen. Die Program- miereinstellungen für die DX6i, DX7/DX7se, DX7s und DX8 fi nden Sie unten aufgelistet. Die Spektrum AirWare Software für dieses Modell ist auch als Download auf der Spektrum Communitiy Seite verfügbar. HINWEIS: Wenn Sie einen Futaba-Sender mit einem Spektrum DSM-Modul verwenden, müssen Sie den Gaskanal reversieren (umkehren) und danach das System neu binden.
Verstehen der grundlegenden Flugsteuerung Bitte nehmen Sie sich ausreichend Zeit um sich mit der Steuerung ihres mCP X BL vertraut zu machen. Steigen Sinken Mehr Gas Weniger Gas (Positiver Pitch) (Negativer Pitch) Seitenruder Nase dreht links Nase dreht rechts Seitenruder links Seitenruder rechts Nick Vorwärts...
Fliegen des mCP X BL Auswahl der Location Der Blade mCPX kann draussen oder in größeren Indoorfl ächen wie einer Turnhalle gefl ogen werden. Bitte beachten Sie lokale Bestimmungen bevor Sie sich einen Platz zum Fliegen suchen. Suchen Sie sich immer eine große freie Fläche weit weg von Menschen und Objekten.
Nachfl ugkontrolle und Wartungscheckliste Kugelköpfe Stellen Sie sicher, dass die Kugelköpfe sauber in den Kugelpfannen sitzen. Diese dürfen nicht zu fest sein und auch nicht nicht zu lose. Zu lose Kugelköpfe können sich bei dem Flug lösen und einen Absturz verursachen. Reinigen Trennen Sie den Akku bevor Sie den Hubschrauber reinigen.
Leitfaden zur Problemlösung Problem Mögliche Ursache Lösung Schalten Sie den Sender aus und bringen in Sender ist während des Bindevorganges weiter weg vom Luftfahrzeug, trennen und zu nah am Luftfahrzeug. verbinden den Flugakku erneut und folgen LED auf dem Empfänger blinkt den Bindeanweisungen.
Garantie und Service Informationen Warnung Sicherheitshinweise Ein ferngesteuertes Modell ist kein Spielzeug. Es kann, wenn es Dieses ist ein hochwertiges Hobby Produkt und kein Spielzeug. Es falsch eingesetzt wird, zu erheblichen Verletzungen bei Lebewesen muss mit Vorsicht und Umsicht eingesetzt werden und erfordert und Beschädigungen an Sachgütern führen.
Explosionszeichnung und Teileliste Artikelnr Bezeichnung Artikelnr Bezeichnung Blade mCP X BL: Fbl BL 3n1 H BLH3909 Blade mCP X BL: Kabinenhaube A BLH3901 Kontrollboard ,RX/ESC/Gyros: I BLH3910 Blade mCP X BL: Heckfi nne Blade mCP X BL: Heckrohr mit Blade mCP X BL: Federspindel...
Blade mCP X BL: Anlenkungen Q BLH3916 EFLC4000* E-fl ite Netzteil 1.5A; EU Stecker Rotorkopf BLH3917 Blade mCP X BL: Kleinteile Set E-fl ite Celectra 2S 7.4V DC Li-Po EFLUC1007 Ladegerät Blade Getriebe : BMSR; mCP X; R BLH3506 mSRX * Das aktuelle Ersatzteil kann sich vom Originalteil Blade Servogestänge mit Kugelp-...
Deutsche und Englische Fassung EN ISO/IEC 17050-1:2010 Declaration of conformity (in accordance with ISO/IEC 17050-1) No. HH2012092801 Horizon Hobby GmbH Hamburger Straße 10 D-25337 Elmshorn erklärt das Produkt: BLH mCP X BL BNF BLH3980 declares the product: BLH mCP X BL BNF BLH3980 Geräteklasse: equipment class: den grundleegenden Andforderungen des §3 und den übrigen einschlägigen Bestimmungen des FTEG (Artikel 3 der...
Page 31
REMARQUE La totalité des instructions, garanties et autres documents est sujette à modifi cation à la seule discrétion d’Horizon Hobby, Inc. Pour obtenir la documentation à jour, rendez-vous sur le site horizonhobby.com et cliquez sur l’onglet de support de ce produit. Signifi...
Page 32
Caractéristiques générales du mCP X BL Bind-N-Fly Châssis - Blade mCP X BL Inclus Moteur principal et d’anticouple - Brushless Installés Electronique embarquée - Module 3 en 1 RX/servos/mixage/Contrôleurs/Gyros...
Mises en garde relatives au chargement L’émetteur (EFLUC1007) inclus dans votre hélicoptère • Faites toujours l’inspection de la batterie avant la a été conçu pour charger la batterie Li-Po incluse en charge, et ne chargez jamais des batteries hors toute sécurité. d’usage ou endommagées.
Préparation au premier vol 1. Sortir et inspectez les composants 5. Affectez à votre hélicoptère votre émetteur compatible DSM 2. Commencez à charger l’accu de vol 6. Testez les commandes 3. Installer l’accu dans l’hélicoptère (si l’accu est totalement chargé) 7.
® Programmez votre émetteur Programmez votre émetteur avant de tenter de l’affecter ou voler. Si les valeurs de gaz et de pas programmées sont incorrectes, l’hélicoptère ne répondra pas. Les valeurs de programmation de l’émetteur sont indiquées ce des- sous pour les Spektrum DX6i, DX7, DX8 et DX18. Le fi chier du modèle pour Spektrum DX8 est aussi disponible en téléchargement en ligne sur le site Spektrum DX8 Community.
® DX8/DX18 Liste des réglages Liste des paramètres Expo Courbe de gaz Type de modèle 0-AILE NORM 100% HELI 0-ELEV ST-1 100% 90% 100% 0-RUDD 100% 0% ST-2 100% 100% 100% 100% 100% 1-AILE 100% 40% HOLD Type de plateau 1-ELEV 100% 40% 1 Servo Normal...
Apprennez les commandes de base Si vous ne maitrisez pas les commandes de votre mCP X, prennez quelques minutes pour vous familiariser avec les commandes avant le premier vol. Montée Descente Manche des gaz Manche des gaz vers le haut vers le bas (Pas collectif positif) (Pas collectif négatif)
Choix de l’aire de vol Le Blade mCP X BL peut voler en extérieur ou en intérieur dans un gymnase. Consultez la législation et la réglementation locales en vigueur avant de choisir une zone où souhaitez faire voler votre hélicoptère. Toujours sélectionner une large zone, ouverte et à...
Inspections après-vol et Maintenance Assurez-vous que l'articulation à rotule plastique maintient bien la rotule de com- Articulations mande, sans être cependant trop serrée (collant) à la rotule. Si l'articulation est trop à rotules lâche par rapport à la rotule, elle peut se séparer de la rotule en cours de vol et provo- (ball links) quer un écrasement au sol.
Problème Cause possible Solution Éloignez l’émetteur allumé à quelques pas L’émetteur était trop proche de l’avion de l’avion, déconnectez la batterie de vol pendant le processus d’affectation de l’avion, puis recommencez le processus d’affectation La DEL du récepteur Mettez l’émetteur sous tension, puis réef- clignote rapidement et Le bouton ou l’interrupteur Bind n’a fectuez l’affectation en maintenant le bouton...
Limitation des dégâts Horizon ne saurait être tenu pour responsable de dom- revendeur qui conviendra avec Horizon d’une décision mages conséquents directs ou indirects, de pertes de appropriée, destinée à vous aider le plus rapidement revenus ou de pertes commerciales, liés de quelque possible.
Vue éclatée et listing des pièces détachées Ref # Description Ref # Description Mode fl ybarless 3 en 1, RX/ Axe de pieds de pales avec joints A BLH3901 J BLH3911 Contrôleurs/Gyros toriques, paliers et accessoires Poutre avec support moteur et Servo linéaire longue course B BLH3902 K SPMSH2026L...
Informations de conformité pour l’Union européenne Déclaration de conformité (conformément à la norme ISO/IEC 17050-1) No. HH2012092801 Produit(s): BLH mCP X BL BNF Numéro(s) d’article: BLH3980 Catégorie d’équipement: L’objet de la déclaration décrit ci-dessus est en conformité avec les exigences des spécifi cations énumérées ci-après, suivant les conditions de la Directive R&TTE Directive 1999/5/EC et CEM Directive 2004/108/EC et LVD...
Page 45
AVVISO Tutte le istruzioni, le garanzie e gli altri documenti pertinenti sono soggetti a cambiamenti a totale discrezione di Horizon Hobby, Inc. Per una documentazione aggiornata sul prodotto, visitare il sito horizonhobby.com e fare clic sulla sezione Support del prodotto. Convenzioni terminologiche Nella documentazione relativa al prodotto vengono utilizzati i seguenti termini per indicare i vari livelli di pericolo potenziale durante l’uso del prodotto:...
Page 46
Caratteristiche Blade mCP X BL Bind-N-Fly Struttura – Blade mCP X BL Compreso Motore principale e di coda – Brushless Montato Elettronica di bordo –...
Avvertenze e indicazioni per la batteria e il caricabatterie Il caricabatterie (EFLUC1007) incluso nella confezi- • Controllare sempre le batterie prima di caricarle per one del mCP X BL è stato concepito per caricare in evitare di caricare batterie esaurite o danneggiate. sicurezza la batteria Li-Po in dotazione.
Celectra (EFLUC1007) Pacco batteria Li-Po 2S 7,4 V 200 mAh 30C (E-fl ite EFLB2002S30) La batteria Li-Po 2S del Blade mCP X BL dispone di un connettore EFL2 che ne consente una carica sicura mediante il caricabatteria Li-Po e l’adattatore forniti in dotazione.
® Programmazione del trasmettitore Programmare il trasmettitore prima di tentare di collegare o fare volare l’elicottero. Di seguito, sono indicati i valori di programmazione del trasmettitore per i modelli Spektrum DX6i, DX7/DX7se, DX7s, DX8 e DX18. I fi le del modello Spektrum per i trasmettitori dotati del software AirWare sono disponibili anche per il download online sul sito della community Spektrum.
Comprensione dei comandi di volo primari Se non hai familiarità con i comandi dell’mCP X, è bene che spenda qualche minuto per apprenderli prima di provare a farlo volare. Throttle Salita Discesa Motore in su Motore giù (Passo collettivo positivo) (Passo collettivo negativo) Timone Il naso imbarda a...
Scegliere il posto Il Blade mCP X BL si può far volare all’esterno o all’interno ma in luoghi spaziosi, come una palestra. Prima di sceg- liere il posto conviene informarsi sulle leggi e ordinanze locali che potrebbero impedire l’utilizzo dei modelli volanti RC.
Throttle Hold Il Throttle hold è utilizzato per spegnere i motori dell’elicottero se l’elicottero è fuori controllo, in pericolo di schian- tarsi o in entrambi i casi. Attiva throttle hold in qualsiasi momento in cui l’elicottero sia in pericolo di schiantarsi per ridurre la possibilità...
Guida alla soluzione dei problemi Problema Causa possibile Soluzione Riposiziona i comandi con lo stick del Throttle in posizione alto throttle e il trim del throttle al centro o nella impostazione più in basso L’elicottero non si iniz- Imposta la modalità di volo su OFF/0 e Interruttori non in posizione normale ializza disattiva il throttle hold...
Page 55
Problema Causa possibile Soluzione Spegnere il trasmettitore e allontanarlo Il trasmettitore è troppo vicino all’aereo maggiormente dall’aereo e poi rifare la durante la procedura procedura Il LED sul ricevitore lam- peggia ma l’aereo non si Il pulsante o l’interruttore appositi non Spegnere il trasmettitore e rifare la proce- connette (durante sono stati trattenuti in posizione ab-...
Disegno dell’Esploso e Lista delle Parti Codice Descrizione Codice Descrizione Unità di controllo Flybarless BL H BLH3909 non mostrato: mCP X BL A BLH3901 3n1,RX/ESC/Gyros: mCP X BL I BLH3910 Impennaggio verticale: mCP X BL Tubo coda con supporto rotore: Alberino portapale con o-ring, B BLH3902 J BLH3911...
Durata della Garanzia Periodo di garanzia Indicazioni di sicurezza Garanzia esclusiva - Horizon Hobby, Inc., (Horizon) Questo è un prodotto sofi sticato di hobbistica e non garantisce che i prodotti acquistati (il “Prodotto”) sono è un giocattolo. Esso deve essere manipolato con privi di difetti relativi ai materiali e di eventuali errori di cautela, con giudizio e richiede delle conoscenze montaggio.
Dichiarazione di conformità (in conformità con ISO/IEC 17050-1) No. HH2012092801 Prodotto(i): BLH mCP X BL BNF Numero(i) articolo: BLH3980 Classe dei dispositivi: 1 Gli oggetti presentati nella dichiarazione sopra citata sono conformi ai requisiti delle specifi che elencate qui di seguito, seguendo le disposizioni della direttiva europea R&TTE 1999/5/EC e CEM direttiva 2004/108/EC e LVD...