Other Accessories - FingerTec R2 Installation Manual

R2c
R2c
suppor t@finger tec.com
Step 4
Setting Up Data Communication
(Skip this step if you are using USB flash disk to transfer data)
The data communication ports are positioned at the rear of the ter-
minals, please refer to the diagrams shown on Step 3 to deter-mine
the wiring. Plug the communication jacks (TCP/IP, RS232 or RS485)
to the corresponding ports.
TCP/IP – LAN Connection
For TCP/IP connection, plug the special RJ45 jack into the TCP/IP
(LAN) Port of the terminal. Connect the other end (normal RJ45 jack)
to the local area network hub or a PC. Configure the device ID, IP ad-
dress, subnet mask and Gateway in the terminal (refer to the hard-
ware user manual for details).
RS232 – Serial Port Connection
Plug the communication jack that is provided in the package to
connect to the communication port of the terminal. Select wires
with label RX, TX and GND, and connect the other end of these wires
to a DB9 female connector. Configure the device ID and baudrate of
the terminal (refer to the hardware user manual for details). Use the
normal RS232 cable to plug into the RS232 port of the terminal.
Rear of Terminal
*Yellow – RS485+
*Blue – RS 485 -
Black - GND
Red – +12V
Black – GND
Dip Switch Setting
RS485 – Serial Port Connection
Plug the communication jack that is provided in the package to con-
nect to the communication port of the terminal. Select wires with
label RS485+, RS485- and GND, and connect the other end of these
wires to an RS232/485 data converter. Connect the other end of the
data converter to a DB9 female connector. Configure the device ID
and baudrate of the terminal (refer to the hardware user manual for
details).
Step 5
Finalizing the Installation
1. Check that all cable connections are done correctly.
2. Attach the terminal to the corresponding back plates and
tighten the screws to secure the terminal on the wall.
3. Switch on the power to the terminal.
4. Start using the terminal.
Note:
Rear of Master 1. The R2c will only work with R2 (FEM 565)
Terminal
or H2i master terminals.
2. The R2c can share the 12VDC pow-er
Blue – RS485+
supply with the master terminal.
3. It is recommended to use RS485 con-
Yellow – RS 485 -
nection cables with a shielded twisted
pair to achieve an opti-mum speed of
Black - GND
data transfer.
+ 4. Do not adjust the dip switch unless you
12VDC
_ are connecting the R2c with the i-Hub
power supply
controller. If your R2c is unable to send
any fingerprint or card data to the mas-
ter terminal, please check the dip switch.
Make sure it is set to the default settings
as highlighted.

Other Accessories

FingerTec offers complementing accessories which can be used with
your terminals. These optional accessories are available at
http://accessory.fingertec.com
AdapTec Plus
The AdapTec Plus is a 12VDC power supply inclusive of a 110~
240VAC switching linear power. The AdapTec Plus supplies 12VDC
power to the FingerTec terminal and door lock system as well
as charges a 12VDC 7.0Ah backup battery simultaneously. Dur-
ing an event of a power failure, the back up battery automati-cally
provides power to the terminal and maintains the door lock system.
The AdapTec Plus also prevents a secured door from being opened if
it has been tampered with.
Mini UPS
Mini UPS 12VDC is a mini portable backup power
supply with 12VDC output, supplying 12VDC
power for FingerTec Door Access & Time Attend-
ance terminals.
Enclosures
An acrylic-made enclosure that protects your terminal from the risk of
meddling by unauthorized individuals. Our custom made enclosure
are specially designed to fit your terminal perfectly with specific open-
ings for fingerprint scanner and buttons. Our enclosure can be used to
mitigate surrounding mild environmental hazards and help lengthen
the lifespan of the terminals. However, do note that the enclosure is
not dust-resistant and waterproof if subjected to extreme weather
conditions.
Door Lock Accessories
FingerTec offers various door locks accessories to complement
FingerTec door access product range.