Advertisement
Advertisement
Table of Contents
Related Manuals for Fagor Advance
Summary of Contents for Fagor Advance
- Page 1 TECHNICAL MANUAL DISH WASHER “ADVANCE” Page 1 of 22 10/11/2009...
- Page 2 PLATFORM The platform used for controlling the low range, ADVANCE dishwasher (front loading, top loading and glasswasher) is shown below. ADVANCE Temperature Card Main Card Assembly Serigraphy control card Page 2 of 22 10/11/2009...
- Page 3 As can be seen from the picture, the platform has 2 cards, the main controller card and the auxiliary temperature card, in addition to a membrane keyboard with 4 buttons and 5 LEDs permitting interaction with the appliance. TEMPERATURE CARD The temperature card is powered through the control card but does not have any communication with this card.
- Page 4 The configuration of the DIP-Switches is as follows: DIP1: Door If DIP1=0 Glass washer and front loading. To begin a new wash cycle, select the required programme, the appliance is on stand-by meanwhile If DIP1=1 Top loading: To start a new wash cycle, just open and close the door, and the last used programme is run DIP2: Regeneration If DIP2=0...
- Page 5 FAGOR ELECTRONIC ADVANCE MODEL DIP1 DIP2 DIP3 DIP4 CYCLE TIMES (s) OTHER GLASSWASHER MODELS OFF OFF OFF OFF P1=90 / P2= 120 / P3=180 AD-15 D , AD-21 D OFF OFF OTHER GLASSWASHER MODELS A.F. OFF OFF P1=60 / P2= 90 / P3=180...
- Page 6 DIPS Page 6 of 22 10/11/2009...
- Page 7 INTERFACE One of the possible serigraphic combinations (membrane keyboard) is shown below. This has been designed to interact with the 5 RELAY card. These are the components of the above combination: B1 (ON/OFF button) Button for switching appliance on/off. The button should be pressed for 2 seconds L1 (ON/OFF LED) LED indicating whether the appliance is ON or OFF.
- Page 8 L2 (LED P1) If the appliance is washing, this LED remains lit. It is also lit if the appliance is in PAUSE mode, i.e., if the door has been opened If the descaler or drainage pump function is activated, the LED flashes If the appliance is not washing, this LED is off.
- Page 9 B4 (Button P3) If this button is pressed once, the dishwasher starts to wash with programme 3 If the button is pressed for 3 seconds, this activates the function corresponding to the right icon (Cold rinse or indefinite cycle, depending upon the DIP1 configuration) If DIP1=0 and DIP2=0: Cold rinse: The cold rinse solenoid valve remains on while the button is pressed If DIP1=1&...
- Page 10 GENERAL OPERATION To switch on the appliance, press button B1 (Button ON/OFF), when the required programme button is pressed the dishwasher starts, provided that the tank has been filled with water. When the programme is selected the machine starts and runs for the time established for this cycle, starting the countdown to zero when the machine stops.
- Page 11 DIAGNOSTICS The software should also diagnose any faults, informing of the action via impulse trains of the ON/OFF LED. The trains are formed of X 0.5” impulses (ON) and a wait of 2”, as shown in the diagram below. Example of a 2-impulse train The diagnostics defined are listed below: 1.
- Page 12 Page 12 of 22 10/11/2009...
- Page 13 Page 13 of 22 10/11/2009...
- Page 14 Page 14 of 22 10/11/2009...
- Page 15 Page 15 of 22 10/11/2009...
- Page 16 Page 16 of 22 10/11/2009...
- Page 17 Water Power(kW) Duration Capacit Consumptio Voltage Basket inlet Resistor Min. rinse weigh MODE power (mm) pressure supply. Tub absorb cycle tub(l) water(l) (kg) 2÷4 kg/cm2 AD-15 350x35 (28÷56psi) 2.66 3.5÷5 Kg/cm2 2 MAX. (42÷70psi) (Controllable) 2÷4 Kg/cm2 AD-21 (28÷56psi 3.06 3.5÷5 Kg/cm2 400x40...
- Page 18 Water Power(kW) Basket, Capacit Consumptio Power supply Cycle inlet Drainage hose Resistor square rinse weigh MODEL voltage duration pressure Dru Tub absorb (mm) tub(l) water(l) (kg) AD - 64 6.65 (200÷400 kPa) AD - 64B (2÷4 Kg./cm2) AD - 64B-BT (28÷56 psi) 6.72 AD –...
- Page 19 NOTES Page 19 of 22 10/11/2009...
- Page 20 NOTES NOTES Page 20 of 22 10/11/2009...
- Page 21 NOTES Page 21 of 22 10/11/2009...
- Page 22 Page 22 of 22 10/11/2009...