NOTICE NOTICE BEFORE INSTALLATION This manual serves basic operation on installation, and operation of DVR (Digital Video Recorder). User who first operates DVR, or is not accustomed to use is strongly recommended to contact manufacturer, or supplier while installation, and to use in order to receive the technical service. All users have to operate DVR after having read this manual sufficiently even though they are very skilled at this unit. Please keep notice at this manual to protect your safety from danger, or property. Please keep this manual on such a place where can easily be reached after having read it all. NOTICE FOR SAFETY Please make sure of usage after bearing the following contents in mind to shorten the safety, and product failure before its operation. ...
Page 6
DO NOT SHOCK IN MOVE, AND INSTALLATION. ▪ Please check rating voltage (standard:DC12V5A, high‐end:12V8A) before power on. ▪ Please check power off before installation. ▪ Avoid any place with moisture because of electric shock, and fire. ▪ Avoid any place with moisture, dust, or soot. ▪ Avoid any place with direct sunlight, or heating appliances. ▪ Avoid high, or low temperature. ▪ Procure sufficient air ventilation for the connection of system wiring. ▪ Don't install near to electronic devices such as radio, or TV. ▪ Install in sufficient air ventilation, and no vibration. ▪ Please take care of not putting the electric product into the cooling fan. ▪ Don't use water, or cleanser in surface cleaning to prevent an electric shock . ▪ Please clean system by dry towel in external cleaning. ▪ Do not pull power cord forcefully. ▪ Do not place any heavy objects on the main system. ▪ Do not open, or disassemble DVR without an assistance of qualified service personnel. ▪ Please power off in case of moving DVR. ▪ Please equip with the safety facility to diminish the loss for electricity failure, and lighting. ...
Page 7
This equipment had been tested and found to comply with the limits for CLASS A digital deice, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment. FCC Compliance Statement Caution : Any change, or modification in construction of this device which are not expressly approved the party responsible for compliance could avoid the user‘s authority to operate the equipment . NOTE : This equipment has been tested, and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. This limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, can radiate radio frequency energy, and , if not installed, and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which cause the user will be required to convert the interference at his own expense.
OVERVIEW 2.1 FEATURES 1. SURVEILLANCE ►Real time moving picture (Max. MPEG‐4 480 Frame (Basic 16CH)) . ►Multi screen display (Basic on 16CH): Single / 4 / 6 / 9 / 13 / 16 . ►PIP (Picture In Picture) . ►Auto sequence. ►Multi output monitor (Output monitor 1, Spot 1, S‐Video 1, VGA 1). ►PTZ (Pan / Tilt / Zoom). ►Digital Zoom (X2) ►Mosaic function . ►Video loss sensor detection. ►External alarm, and recording event list for motion detection. ►Supported user friendly GUI interface, remote controller, and mouse. 2. RECORDING ►Recording in high quality of MPEG‐4 real time motion picture ►Recording resolution setup adjustable to backup capacity (16CH Max. 480 frame) ►Multi recording for manual, event, and schedule. ►One time system for display, recording, playback, backup, and network. ►Easy setup for recording resolution, and motion detection part. ►Supported manual, and reserved recording function. ►Supported Individual channel recording. ...
Page 9
3. PLAYBACK ► Playback by event, time, and channel. ► Mouse controlled search ► Playback for still image, and search for still display detection. ► Playback by event list (sensor, motion). ► Easy search with remote controller, and mouse. ► Digital zoom in playback display screen (Digital Zoom X2) 4. NETWORK ► Supported PPPoE, Static and DHCP. ► Supported itself, and general DDNS. ► TCP/IP. ► Unlimited multi access (Recommended 10). ► Supported multi mode (LIVE/PB/NETWORK BACKUP/FILE PLAY) ► Multi DVR Control ► Remote Control ► PTZ Control ► Save AVI ► Save & print still ► Auto update ► Web viewer ► File viewer ►...
Page 10
5. AUDIO ► One time recording for real time 4CH audio input. ► Input : 4CH(rear 4), Output : 1ch(rear). ► Audio channel selectable. 6. BACKUP ► Backup by network viewer. ► Supported multi backup function : CD±R,CD±RW,DVD±R,DVD±RW and USB. 7. OTHERS ► S‐Video, Spot output. ► Alarm In/Out, RS‐485, RS‐232 Connections. ► Connection of loop‐through. ► Supported multi language. ► One remote controller for Max. 4 DVRs. ► Easy operation with USB mouse. ► Easy firmware upgrade with USB, network and webhard. ...
2.2 PACKING DETAILS DVR includes main unit, and its following accessories in the package packing. Please check all items if there is all packed inside as below. Please contact manufacturer, or supplier if found missing accessories. DVR UNIT Premium‐series Standard‐series Economy‐series...
Page 12
Contents Premium Standard Economy Program CD Remote controller Quick guide User manual Batteries Power code Adaptor (12V8A) (12V5A) (12V5A) HDD screw Rack mount X (OPTION) X Sata HDD data cable 3 2 1...
2.3 NAMES AND FUNCTION 2.3.1 FRONT PANEL PREMIUM DVR SECTION NAME FUNCTION DVD RW Back up recording &playback video in DVD/CD BACKUP USB 2.0 External connector (USB & MOUSE) INFO Show information for DVR system, HDD and firmware DISPLAY Change divided display in live&playback mode FUNCTION PTZ Control function of PTZ BACK UP Go to backup mode SEARCH Go to search mode REW Rewind (MAX.x32) SEARCH 1 PLAY/PAUSE Play / Pause FAST Fast forward STOP Stop RECORDING 9 REC Recording or not SYSTEM Q.MENU Go to Q.MENU mode SETUP POWER Power ON/OFF REC ...
Page 14
STANDARD DVR SECTION NAME FUNCTION CHANNEL CH 1‐10 Channel selection in live, and play back display BACKUP USB 2.0 External connector of USB, and mouse DISPLAY Change split display in live, and play back AUTO Sequence operation, and stop PIP Another display in one channel display. OSD FUNCTION Icon, time table, and channel name in monitor display. INFO System status, HDD status, and firmware information. BACK UP Back up mode. PTZ Use, or stop of PTZ function. POWER Electric status. Recording feasibility LED SIGNAL ALARM Event detection NET Network connection POWER SUPPLY 11 POWER Stable stop of system operation Q.MENU SYSTEM SETUP Q.MENU mode REC ...
Page 15
ECONOMY DVR CLASSIFICATION NAME FUNCTION USB 2.0 BACKUP External terminal(USB, Mouse) SEARCH SEARCH Search mode REW Reverse play back speed in play back mode PLAY/PAUSE Play back start, or temporary pause LED DISPLAY FAST Forward play back speed in play back mode STOP Stop play back mode and return to live display mode Q.MENU Q.MENU Q.MENU mode MULTIPLE DISPLAY Multiple display mode RECORDING REC Urgent recording POWER POWER Stable stop of system operation ▲ ▼ DIRECTION KEY Left/right, and up/down direction key. Channel change REMOTE SENSOR Remote controller sensor CONTROLLER POWER Electric status Recording ...
2.3.2 REAR PANEL PREMIUM & STANDARD DVR 16CH INPUT / OUTPUT FUNCTION CONNECTOR NAME AUDIO IN Audio input & RCA input connector. CH1~16 BNC input connector of camera LOOP OUT BNC(loop) output connector of camera DC12V Connect power code of adaptor socket SEN.IN/AL/485 External sensor input relay output, PTZ camera connector RS‐232 RS‐232 terminal LCD monitor output connector External(USB, MOUSE) connector Network (RJ‐45) connector AUDIO OUT Audio output connector S‐VIDEO S‐VIDEO monitor connector VIDEO OUT Monitor output connector by BNC SPOT OUT Spot monitor output connector by BNC...
2.3.3 REMOTE CONTROLLER NAME FUNCTION POWER Power ON/OFF Recording CHANNNEL Channel button Osd ON/OFF INFO Information of DVR PAN/TILT MODE ZOOM Zoom/Focus mode MUTE Audio ON/OFF Show log listT MENU Q.MENU ▲ ▼ DOWN LEFT RIGHT ENTER MENU SEARCH Search recording list BACK UP Backup Reverse play PLlay and pause Fast forward ■ STOP DISP Display mode PIP mode AUTO Auto sequence SPOT Spot monitor...
2.3.4 Q‐MENU Group Conversion Rec : Recording ON/OFF System Setup Search recording Display : Screen division Backup (copy) (1,4,6,9,13,16CH ) Auto : Auto sequence display Info : System information Ptz : Pan‐tilt camera PIP : Pip mode control Digital zoom Audio : Audio ON/OFF Osd ON/OFF...
2.4 SPECIFICATION PREMIUM DVR Model SVR‐1648 SVR‐1824 SVR‐412 16/8/4 Channel Input(BNC) Video Input Video Signal NTSC / PAL, 1V 75 Ohm Video Output 5 Outputs (Composite BNC, VGA, S‐Video, Loop through, Spot) Compression Enhanced MPEG‐4, M‐JPEG Real Time Watching / Recording / Playback / Networking / Pentaplex Operation Back‐Up Archiving Resolution NTSC – 704X480 / PAL – 704X576 Speed Real Time Display Display 16, 13, 9, 6, 4, 1 screen Mode PIP, Auto Screen NTSC – 704X480, 704X240, 352X240, Resolution PAL – 704X576, 704X288, 352X288 Recording CIF 480ips/400ips CIF 240ips/200ips CIF 120ips/100ips REC &PB Speed HD1 240ips/200ips HD1 240ips/200ips HD1 120ips/100ips...
Page 22
System Upgrade USB / Network Signal Loss Detection BEEP / BEEP+OSD / OSD / OFF Motion Detect Trace YES / NO Motion Sensitivity Mosaic ON/OFF Zoom Dimension 430(W) X 92(H) X 380(D)mm Weight 8.0kg(without HDD) Power Supply DC 12V 8A Approval FCC, CE...
Page 23
STANDARD DVR Model SVR‐1648S SVR‐1624S SVR‐824S SVR‐412S 16/8/4 Channel Input(BNC) Video Input NTSC / PAL, 1V 75 Ohm Video Signal Video Output 5 Outputs (Composite BNC, VGA, S‐Video, Loop through, Spot) Compression Enhanced MPEG‐4, M‐JPEG Real Time Watching / Recording / Playback Pentaplex Operation / Networking / Back‐Up Archiving Resolution NTSC – 704X480 / PAL – 704X576 Speed Real Time Display Display 16, 13, 9, 6, 4, 1 screen Mode PIP, Auto Screen NTSC – 704X480, 704X240, 352X240 Resolution PAL – 704X576, 704X288, 352X288 Recording& CIF 480ips/400ips CIF 240ips/200ips CIF 240ips/200ips CIF 120ips/100ips REC &PB Playback HD1 240ips/200ips...
Page 24
System Control Front Keypad(6X6), Remote Controller, Mouse Language Multi OSD System Upgrade USB / Network Signal Loss Detection BEEP / BEEP+OSD / OSD / OFF Motion Detect Trace YES / NO Motion Sensitivity Mosaic ON/OFF Zoom Dimension 430(W) X 75(H) X 360(D)mm Weight 7.50kg (without HDD) Power Supply DC 12V 5A Approval FCC, CE...
Page 25
COMPACT DVR Model SVR‐824E SVR‐412E 8/4 Channel Input(BNC) Video Signal Video Input NTSC / PAL, 1V 75 Ohm Compression Enhanced MPEG‐4, M‐JPEG Real Time Watching / Recording / Playback / Networking/ Pentaplex Operation Back‐Up Archiving Resolution NTSC – 704X480 / PAL – 704X576 Speed Real Time Display Display Mode 9, 6, 4, 1 screen PIP, Auto Screen NTSC – 704X480, 704X240, 352X240 Resolution PAL – 704X576, 704X288, 352X288 Recording REC &PB CIF 240ips/200ips HD1 120ips/100ips & Playback Speed D1 120ips/100ips D1 60ips/50ips Mode Continuous, Schedule, Event(Motion, Sensor) Search...
Page 26
Signal Loss Detection BEEP / BEEP+OSD / OSD / OFF Motion Detect Trace YES / NO Motion Sensitivity Mosaic ON/OFF Zoom Dimension 17.0”x14.1”x3.0”(430x360x75mm) Weight 4.5kg(NET),5.0KG(GROSS) Power Supply DC 12V 5A Approval FCC, CE...
3.2 INDIVIDUAL CONNECTION 3.2.1 POWER Please connect adaptor with socket as below NOTE 1. Please connect a rate adaptor with DVR system. 2. Please use adaptor of above DC12V 8A for 3 HDD. 3. After pressing the power button on front panel, and checking message on monitor, please separate power socket from DVR system in case of power off.
3.2.2 RACK MOUNT INSTALLATION User can stick DVR into enclosed rack mount, and use it as below. This function supports Premium & Standard series. 3.2.2 VIDEO & AUDIO ▮ VIDEO INPUT Please connect DVR, and CCTV camera with CAMERA IN connector on rear panel by coaxial cable. This DVR system can be connected with cameras of maximum NO. of 16/8/4. ...
Page 30
NOTE 1. Video input type should be either NTSC or PAL, Don't use two types in mix. 2. Automatic setup for 75Ω resistance 75Ω terminal resistance is set up, automatically split into, and becomes Hi‐Z status when connected with video output connector under input one. CAUTION 1. Video vibration is possible when user connects BNC of camera with loop connector without connecting input connector. Be sure to link it to camera input connector. 2. Too much vibration is possible in case of not linking BNC connector to camera output without connecting camera cable. ▮ VIDEO OUTPUT Please connect DVR with monitor by video cable. ...
Page 31
▮ AUDIO INPUT Please connect with jack MIC built‐in camera in AUDIO IN connector, or external audio device at the back of this DVR. [AUDIO INPUT CONNECTORS] [AUDIO OUTPUT CONNECTORS] PREMIUM DVR COMPACT DVR STANDARD DVR In audio output, default channel color is in red color. NOTE Please select AUDIO IN channel on recording setup in case of setting up audio input.
Page 32
▮ AUDIO OUTPUT Please connect RCA of speaker built‐in monitor in audio out connector at the back of this DVR. NOTE 1. Four audio input synchronizes audio output for CH1~CH4 in single display. 2. Audio is possible to live, and play back display mode in playback. 3. Audio is not supported in double playback in single display mode.
3.2.3 HDD CONNECTION POWER CABLE DATA CABLE ► Please fix HDD to DVR unit by screws. ► Please connect main board with HDD power cable. ► Please assemble DVR, power on after connecting main board with HDD data cable. Auto format starts after power on. If not, [ System setup ] 4. HDD format => "Yes"...
Page 34
NOTE 1. For HDD connection with DVR unit system, please be sure to power off. 2. For fixing screw to HDD bracket, please don't shock, which may cause HDD breakdown. 3. Please check problem after HDD installation. 4. For HDD problem, or not recognized, please contact manufacturer, or Supplier, and change it into new one. Recording is not properly worked. 5. All data disappear in HDD installation, which is not in the type of format. 6. The firmware upgrade is available only in the HDD connection. 7. When connecting HDD (or additional HDD) to DVR, please be sure to connect data cable to HDD port on main board. If being connected to DVD port, recording data may be damaged. ...
OPERATION 4.1 PRE‐OPERATION Please make sure of power voltage before power on. 4.2 POWER CONNECTION ▮ POWER ON Please make sure of power voltage before power on. 1. Connect DVR to D/C power Jack by using adaptor in the package. 2. Having finished the connection between power cable and external device, power is on by pressing button on the rear panel. The following display appears. 3. Booting time takes about 30 seconds after power is on. 4. Video signal is automatically detected when power is on. 5. The menu values set by user is not changed in sudden power failure.
Page 39
CAUTION 1. User is strongly recommended to use the adaptor in the package that manufacturer provides. 2. The DVR may be fatally damaged by use of different voltage of adaptor. ▮ POWER OFF Press red POWER button on front panel. Its function is mainly to prevent system damage due to suddenly unexpected power off. Pull off adaptor on rear panel when the message appears below. Select YES to power off. System is closing. In this process, user can not return to "power on" mode.
Page 40
Pull off adaptor on rear panel when this message appears. CAUTION "STOP RECORDING" message shows up on monitor when being pressed during recording.
4.3 LIVE DISPALY 4.3.1 SINGLE DISPLAY When user selects one channel in multiple channel mode, this channel is switched over to single channel mode as below. User needs to press one more channel button after +10 button when he selects over channel 10. For example, he needs to press channel 1 Button after +10 Button when selecting channel 11. This channel selection method is the same as both live mode and playback mode. [Full multiple channel ] [Single channel ] NOTE If pressing +10 button twice or any channel button is not followed for about 2 seconds after pressing +10 button, it goes to channel 10.
4.3.2 MULTIPLE DISPLAY ▮ LIVE DISPLAY SCREEN Current date and time DVR status icon Event recording on Audio on Recording on Quick menu Network online NOTE For more details, please refer to Q.menu set up.
Page 43
▮ PLAYBACK DISPLAY MODE Up: Live time Down: Recorded date and time Play back mode Play back speed control icon /▮ ▮ : PLAY / PAUSE : REW ■: STOP : FF : DIGITAL ZOOM NOTE User can play the recording data frame by frame by pressing REW or FF button in playback mode. In 16 multiple channel, user can move to channel 1 by pressing digital zoom button.
Page 44
Press DISPLAY button, and full divided channel mode is switched over to real‐time surveillance display mode. 1. Auto sequence or PIP mode can be switched over to 16 channel display mode by pressing DISPLAY button. 2. Live mode is switched over to 16 channel display → 13 channel display → 9 channel display → 6 channel display → 4 channel display mode in order by pressing DISPLAY button, or clicking the right button of mouse repeatedly. NOTE User can move to next channel by clicking the right button of mouse in single mode. To return to divided channel mode, user needs to press on quick menu or DISPLAY button on front panel. 13 channel display → 9 channel display → 6 channel display → 4 channel display The display channel can be changed by pressing UP/DOWN button in divided channel ...
Page 45
▮ MOSAIC FUNCTION User can make certain area in live mode blurred for private purpose. Mosaic ON 1. Select one channel that user likes to set up. 2. Put the mouse at the starting point you want, and drag it to the desiring area with left‐button pressed. 3. This mosaic function is only available in display mode, and does not affect any recording data even if it is on when Mosaic OFF recording is triggered. 4. To release this function, drag mouse diagonally from the right bottom of set area with it pressed. Mouse starting point NOTE This mosaic function is only available at live display mode.
4.4 AUTO SEQUENCE (AUTO) Live mode is automatically switched over to single channel or 4 channel mode with time interval that is set in display, and auto display mode in AUTO button pressing. ‐ Display mode setup : Menu > Display > Sequence > Mode : single or quad ‐ Interval setup : Menu > Display > Sequence > Interval : 1 sec ~ 60 sec. Press the button again, and DVR stops this function. To release this AUTO function, press DISPLAY button. DVR skips the channel with no video when this function is triggered. [ Single channel ] [ 4 channel ] CH1 ,2,3,4 CH5,6,7,8 CH9,10,11,12 CH13,14,15,16...
4.5 DIGITAL ZOOM User can magnify the area that he wants 2 times digitally. 1. Click on Q.MENU and select the area that you want by pressing direction key buttons. 2. Press ENTER button, and the picture inside angle is magnified digitally. This function is only available at single channel . 3. To release this function, press the ZOOM button again.
4.6 PIP User can monitor small channel together in single channel mode. User can monitor main channel and sub channel together in single channel mode. Various PIP modes are displayed when pressing PIP button repeatedly. The sub channel location is changed when pressing PIP button, or clicking the right button of mouse. The sub channel display is changed when pressing LEFT / RIGHT button of direction key on front panel. The main channel display is changed when pressing UP / DOWN button of direction key on front panel. To stop this function, press DISPLAY button. ...
4.7 SPOT [SPOT monitor] 1. This function leads to only monitor additional monitor as well as main monitor . Main monitor offers all functions of DVR like menu set up, live video display (divided channel display) , and playback. But SPOT monitor supports only live single channel, or live 4 channel display. 2. SPOT monitor also supports AUTO SEQUENCE function, and can set up time interval as user wants. ...
4.8 PTZ PTZ set up is required in menu set up, and PTZ is used for controlling camera with PAN/TILT/ZOOM/FOCUS. 1. Press PTZ button in live divided 16 channel mode, and single channel mode appears. 2. Press ENTER button, and move to each menu like CH, P/T, Z/F. 3. PTZ camera is controlled with LEFT / RIGHT buttons on front panel, mouse, or remote controller. 4. To release this function, press PTZ button again. CH : Channel change P/T : PAN & TILT control Z/F : ZOOM & FOCUS control To function above, please setup PROTOCOL, BAUDRATE, SPEED, ID from MAIN MENU>CAMERA.
CAUTON Make sure that PTZ speed dome camera is properly installed on the relevant channel before PTZ operation. NOTE PTZ mode is available at live single display mode only, not controlled by divided channel display mode. To release this function, press PTZ button again. 4.9 MOUSE By using USB mouse, setting values can easily be adjusted, or changed. ▮ MOUSE OPERATION RIGHT BUTTON LEFT BUTTON MOUSE WHEEL...
Page 52
1. Left button To select menu or to confirm setting value To move to 16/13/6/4 CH in display screen mode To revert into the previous multiple screen mode from 1 CH single screen mode 2. Right button In display screen mode 13 multiple screen mode : To move to next channel by one channel. 9 multiple screen mode : To move to 1‐9 channel and 8‐16channel 6 multiple screen mode : To move to next channel by one channel 4 multiple screen mode : To move to 1‐4, 5‐8, 9‐12, 13‐16 channel To move to next channel from single channel in play back mode To change sub‐channel in PIP mode ▮ KEY BUTTON OPERATION ON FRONT PANEL : To move cursor to left, or right 2. ▼▲ : To move cursor to up, or down : ENTER button. To activate the corresponding function. 4. Q.MENU : To get out of current menu ▮ Remote controller operation : To move to left or right 2. ▼▲ : To move to up or down : ENTER button. To activate the corresponding function 4. Q.MENU : To get out of current menu ...
4.10 OSD ► Time, channel name, and motion activating icon can disappear in order in display mode. Press OSD button on front panel , or button on Q.MENU by stage. [OSD ON] [OSD OFF]...
4.11 RECORDING 4.11.1 NORMAL RECORDING Press REC button, and LED is lighted with red color. Recording starts with record icon and appeared at the right upper side. To release recording, press REC button again and record icon also disappeared accordingly. When recording starts, or releases, the message of START RECORDNG appears, and disappears at the bottom of right side. CAUTON 1. Factory default is set to function the schedule recording . 2. In recording release, record setup should be released from schedule record menu. 3. In release of schedule recording, REC button on front panel can be set, and recording releases. NOTE 1. Password approval is pre‐requisite to stop recording. 2. In the mode of record setup menu, auto recording is effected at the time user wants. (Please refer to schedule record setup from setup menu.)
4.11.2 EVENT RECORDING Event recording is automatically reserved according to time, and date when event setup is set to record setup mode in system setup menu. 4.11.3 SCHEDULE RECORDING Schedule recording is automatically played according to time, and date to be set when schedule setup is set to schedule setup mode in system setup menu. ...
4.12 SEARCH Press SEARCH button on front panel, and the following SEARCH menu appears on screen. Recorded video can be searched, and play backed by NORMAL search (time, and date), by EVENT,and by TIME, performing recording&searching simultaneously. To cancel recording search, and to get back to live display mode, press SEARCH button repeatedly. 4.12.1 NORMAL SEARCH (DATE, AND TIME SEARCH) After pressing SEARCH button, move to the date with yellow color, and press ENTER button. ...
Page 58
When time graph appears, move to the time user wants, and press ENTER button while time is in yellow color. When minute graph appears, move to the area in yellow color, and press ENTER button at the area you want. Recorded video is played back at selected date ** To stop search, and to return to live display mode, press STOP button. NOTE 1. Press MENU button to move to normal search, event search, and date search. 2. Move monthly moving search by pressing UP/DOWN direction key button. 3. The yellow area means recording date in search menu. 4. Search is possible after checking playback to this area.
Page 59
▮ REW,PLAY/PAUSE,FAST,STOP For the file searched by recording search , playback can be controlled through below icon button. ► REW (High speed playback) : Pressing REW button in playback display mode, playback is faster than normal speed (x2, x4, x8, x16, x32) ► FF (fast forward) : Press FAST button in playback display mode, playback is faster than normal speed in the opposite direction. (x2, x4, x8, x16, x32) ► PLAY / PAUSE : Press PAUSE in playback display mode, playback stops temporarily . Press button again, playback starts again. ► STOP : Press STOP button in playback display mode, live display mode is switched over. NOTE After temporary pause in playback display, press FAST/REW button. Playback by frame is possible.
4.12.2 EVENT SEARCH User can search the recording data for motion, sensor detection. Press Q. MENU button on front panel, and move to event search menu. Press enter button on the date in yellow. Event type : To search event recording data by all, motion, sensor ►Motion : Motion detection record ►Sensor : Sensor detection record Channel selection : User can select by all channels, or each channel . Move to the yellow area on time graph. And find the time range you want, moving to there. Then, press ENTER button, and event list appears. ...
Page 61
PAGE : 0001/0042 It means current & total page. Each page has 10 recording lists. Move to next page by left ( ), right ( ) button and go to recording list by up ( ▲ ), down ( ▼ ) button. Press search button in the relevant screen, and DVR displays search screen as below. To monitor event search of other channels, press DISPLAY button, and search the relevant channel. To stop search mode, and get back to live display mode, press STOP button. If user gets out of this menu, press STOP first, and then SEARCH button. ...
4.12.3 TIME SEARCH User can directly input his wanting time & date. He is able to search them. Move to TIME SEARCH menu by pressing Q.MENU button on front panel. Select date, and time to search. Press ENTER button, and play back display appears as below. To stop this search mode, and return to live display mode, press STOP button ...
4.12.4 JOG SHUTTLE SEARCH By using jog shuttle, user can more conveniently search recording data in playback mode. Jog dial Shuttling Jog dial : Convenient to search frame by frame, and the detailed motion in short time in pause mode. Shuttling : To control, and search playback speed by max. 32 times both in forwarding, and opposite direction. NOTE This function is applied to premium DVR only.
4.13 BACK UP User can have backup recorded video display after setting the wanting time with DVD±RW,CD±RW, and USB memory stick. Press backup button, and select media to copy. ** MEDIA FOR BACK UP : DVD± RW,DVD± R,CD± RW,CD± R,USB MEMORY STICK 1. Copying setup 2. Copying… 4. Closing… 3. Burning… 5. Completed...
Page 65
1. Insert blank CD in DVD ROM of DVR. 2. Select DVD ROM from DEVICE selection, and press ENTER button. 3. With the use of direction key button, set up channel, time, date and minute to copy respectively. 4. The copied data size is automatically calculated. 5. Press "START", and back up is completed after above 5 stages. 6. Press BACK UP button to exit to menu. NOTE 1. The format of DVD ROM is automatically performed. 2. Set up START time, and END time is automatically set proportional to media capacity. To changing back up capacity, separate setup is possible. 3. One sheet of DVD supports the capacity of 4.5G(4500MB), and copying time is about 35 minutes. 4. In abrupt switch off, or copying not carried out normally, take out DVD ROM media, and start it from the first stage by re‐insertion. 5. USB copying is in the same way as above. 6. Normal backup may not properly be performed for less than USB free size of 512 MB . CAUTION 1. Don't remove DVD‐ROM, or USB Memory Stick forcefully while copying. It may cause system shutdown. 2. The file viewer function may be changed into dependent upon the specification of computer system.
4.14 BACKUP VIEWER User finds the files below when double clicking backup file. When installing File viewer program, backup file list appears. Each backup file has 1 minute long data. Double click one from backup file list, it is played. ...
Page 67
Back up file is generated per every 1 minute. Audio playback speed control If you want to play backup file in old ofirmware version, press open button and select it that you want. It can be played on new version of backup viewer. Display mode Play, Stop, REW, FF buttons Still image Print & archive...
SETUP MENU 5.1 FACTORY DEFAULT MAIN MENU SUB MENU DEFAULT 1.Language English 2.Resolution High 3.Quality Q.menu 4.Overwrite Yes 5.Pre‐record Yes 6.Remote ID 1.Channel 2.Title CH01 3.Adjust 1.Contrast 2.Brightness 3.Hue Camera 4.Saturation 5.B/W 4.PTZ Protocol OFF 5.PTZ Baudrate 9600 6.PTZ speed 7.PTZ ID 1.Sequence 1.Conversion type Single 2.Conversion interval 01 second 2.Osd Display 1.Icon Yes ...
Page 69
MAIN MENU SUB MENU DEFAULT 1.Sensor 2.Sensor type Off 3.Notion 4.Motion set 1.Trace 2.Sensitivity 3.Area Off Event 5.Alarm 1.Alarm1 2.Alarm2 Sensor 3.Alarm3 Motion 4.Alarm4 Loss 6.Event time 10seconds 7.POP‐UP Off 8. Pre‐record 1.IP setup 1.Type Dhcp 2.IP address XXX.XXX.XXX.XXX 3.Subnet XXX.XXX.XXX.XXX 4.Gateway XXX.XXX.XXX.XXX 5.Command Port 9201 6.Video Port 9202 7.Web Port 8.PPPoE 1.Id ...
5.2 QUICK SETUP 5.2.1 LANGUGE ‐ English, Korean, Chinese, Russian Etc. This DVR supports 14 countries of language. Select wanting country language with the use of left & right direction key. Factory default set in English. 5.2.2 RESOLUTION The recording resolution can be selected super, high and low. Super (set up till D1 7.5FPS) High (set up till HD1 15FPS) Low (set up till CIF 30FPS ) ...
5.2.3 QUALITY / 1, 2, 3, 4 The recording quality can be set up based on recording resolution The HDD capacity differs from the setting values of 1, 2, 3, 4. 5.2.4 OVERWRITE / ON, OFF Once HDD capacity reaches the full size, it again returns to the first stage. It carries out the Overwrite (yes), and records continually. In setting "No", "HDD FULL" appears at the bottom of display, and record stops. 5.2.5 PRE‐RECORD / ON, OFF Execute, and finish the event recording, and recording time can be extended to 2~3 seconds more than set time. NOTE Pre‐ recording is basically set for about 2~3 seconds, though not in menu. 5.2.6 REMOTE ID / 1, 2, 3, 4, ALL Install the various DVRs at the same place, and one remote controller can control various DVRs respectively by granting ID to them. Only remote controller can be used to control. Setting values are ranged into 1~4, and ALL. ...
5.3.2 TITLE / CH 1‐CH 16 User can set up the installed camera's name by each channel. By moving direction key, press ENETR button, and window appears as below. Change the name of No. 1 camera, and press ENTER after inserting the name with use of mouse, or direction key at the bottom of window. Like the picture on right side, No. 1 camera's name is changed, and stored. Other cameras have the same way NOTE 1. To set up it by maximum 8 letters 2. Korean name not supported (OSD : No. English capital & small letter, Special sign) 3. Default : channel 1.
5.4 DISPLAY 5.4.1 SEQUENCE Sequentially auto display conversion is set up from 1‐16 channels in live display screen. 1.1 MODE / SINGLE, QUAD To set up 1channel, or 4 channel 1.2 INTERVAL ( 1‐60 Second ) To set up the interval of auto display conversion. ...
5.4.2 OSD DISPLAY User can delete icon, title, date, and time by degree in live display screen. 2.1 ICON / ON, OFF To set up icon deletion in live display. 2.2 TITLE / ON, OFF To set up the deletion of camera's name in live display. 2.3 DATE, TIME / ON, OFF To set up the deletion of date, and time in live display. NOTE OSD deletion function not supported in playback display.
5.4.3 VIDEO LOSS When the real‐time camera video loss occurs, it advises BLANK loss status to the relevant channel, or show "L" letters. ►OFF : Not Supported ►OSD : Display video loss status in letter on display ►OSD + BEEP : Display video loss status in letter, and buzzer sound. ►BEEP : Display video loss in buzzer sound ...
5.4.4 SPOT / SINGLE , QUAD Select single, and QUAD mode. Set up conversion interval of SPOT monitor. When the conversion interval is disabled, set one channel of 1~16 ones. The function of auto display conversion can be added. 5.4.5 VIDEO FORMAT / NTSC, PAL User can set the receiving type of respective camera installed each area. ...
5.5. RECORD 5.5.1 RESOLUTION Selectable to recording resolution pertinent to user¡ˉs environment. SUPER (QUALITY) 1 / 2 / 3 / 4 7.5IPS per each channel...
Page 81
HIGH (QUALITY) 1 / 2 / 3 / 4 15IPS per each channel USER SUPER (QUALITY) 1 / 2 / 3 / 4 HIGH (QUALITY) 1 / 2 / 3 / 4 (QUALITY) 1 / 2 / 3 / 4 User is able to set resolution, quality, and recording as he likes to do. If he doesn’t want recording, please set off IPS SETUP form USB SETUP USER. In playback, channel set OFF SETUP is playback in BLANK. [ Recording setup display‐USER ]...
Page 82
[ Recording playback display ] LOW (QUALITY) 1 / 2 / 3 / 4 each channel 30IPS NOTE 1. The recording resolution setup is related to HDD capacity. 2. The recording level (Quality) can be set to 1, 2, 3, 4. 3. Overwrite ON : When HDD is not enough space for back up, return to the first, and recording starts by overwriting the old data.
Page 83
*RECORDING RESOLUTION Resolution Record ips Quality 704x480 Super 704x480 Super 704x480 Super 704x480 Super 704x480 Super 704x480 Super 704x480 Super 704x240 High 704x240 High 704x240 High 704x240 High 704x240 High 704x240 High 704x240 High 704x240 High 704x240 High 352x240 352x240 352x240 352x240 352x240 352x240 352x240...
5.5.2 WATERMARK / ON, OFF Selection of watermark setup. 5.5.3 SCHEDULE SETUP When schedule recording is set to " YES", automatic recording starts at the time, and date user wants. With the use of mouse, or direction key on front side, press "ENTER" on wanting date & time, and schedule recording is changed into yellow green. The time area converted to yellow green is automatically recorded. NORMAL (Yellow green) : Meaning of manual recording, and automatically recorded if fixed time falls on. MOTION (Sky blue) : Auto recording of event video detected at wanting time. SENSOR (Orange) : Auto recording of video detected from separately installed sensor. ...
Page 85
Once schedule recording is set up, auto recording is possible without pre ssing REC button on date, and time user wants. For the schedule recording, there are normal record, motion recording and sensor recording. Schedule record setup Schedule record release With the use of mouse, or direction key on front side, press " ENTER" button on wanting time, and date. If so, time of area to be converted to yellow green is automatically recorded. NORMAL (Yellow green) 1. Once time approaches to the area painted in yellow green, auto record starts. 2. With the use of direction key, wanting time, and date are set up. 3. Press "ENTER" button, and set up. In case of release, press 'ENTER" button again.
Page 86
MOTION (Sky blue) 1. Sensor detects at the time of area painted in sky blue 2. In event schedule, the video of relevant channel is automatically recorded. ...
Page 87
NOTE The following is needed when motion recording is set up. 1) NORMAL recording setup ON : As above picture, 'M' appears on display when not having motion recording from 9~11 AM to 16~18PM, but event recording list is not appeared. At normal recording, recording works normally. 2) NORMAL recording setup OFF : As above setup, undesignated area is not recorded. → In all recording, schedule recording setup has its priority. 3) Event list is recorded for 10 seconds from the first motion happening ( if 10 seconds are set up ). If motion is continually detected for 10 seconds, recording time is prolonged, and shows one event list. 4) Normal recording is more secure than motion recording when the place (bank, train station, etc) motion is going on for long times. SENSOR (Orange) Automatically recording sensor video that is detected at the time of area painted in orange. NOTE If schedule recording is set, it has recording prior to motion and sensor one in turn.
5.5.4 AUDIO INPUT1,INPUT2,INPUT3,INPUT4,LIVE OUTPUT Maximum 4 audio input, and one audio output. In activating audio function, audio icon appears at the top of display screen. ▪ Input : Select 4 channel of 1~16 ones, and input. ▪ Output : Select 1 of input 4 channels, and output. The channel color is showed in red. ...
5.5.5 OVER WRITE / ON, OFF When HDD reaches full size of capacity, it returns to the first stage, and continually records by executing overwrite. In "NO", "HDD FULL" message appears at the bottom of display screen, and record stops. ...
5.6 EVENT User can set up with 'ENTER" button, or MOUSE the detailed article necessary to event record 5.6.1 SENSOR / OFF, OSD, OSD + BEEP, BEEP In sensor detection, select display mode on screen. 5.6.2 SENSOR IN ►CH 1 ~ 16 N.O / N.C / OFF ►User can set up the sensor mode for the relevant channel. ...
N.O : General open mode (NORMAL OPEN ) N.C : General Closed mode (NORMAL CLOSE) OFF : Not set up. 5.6.3. MOTION ‐ OFF, OSD, OSD + BEEP, BEEP In sensor detection of person, or object, select text on the display screen. In setting up "LETTER", "M" appears.
5.6.4 MOTION SET User can set up motion detail by each channel. (1) TRACE ( ON, OFF ) In motion sensor detection, cursor appears in activation according to the moving objects.
Page 93
(2) SENSITIVITY ( 1 ‐ 8 ) User can set up moving sensitivity by each channel. With the use of either left & right direction key, or mouse, it can set up 1~8, and default is set 4. (3) AREA ( FULL, SET, OFF ) ▪FULL : Full part ▪SET : User's area set up ▪OFF : Not set up User can set up record area of motion by each channel, and is available to setup, and release of wanting area from user's menu. ...
Page 94
► In "SET" position, set area appears on the display in yellow green by pressing "ENTER" button with direction key moving. ► In using "MOUSE", drag left mouse, and set up its area in the below direction. [ Part setup as much as drag ] [ Mouse release ] ► In "SET" position, it is changed into display of yellow green when pressing "ENTER" button with direction key moving. By dragging the set area by mouse in diagonal direction, it is released Mouse position...
5.6.5 ALARM Each alarm function can be set for 4 alarms port. ► Alarm 1 Sensor, Motion, LOSS, OFF ► Alarm 2 Sensor, Motion, LOSS, OFF ► Alarm 3 Sensor, Motion, LOSS, OFF ► Alarm 4 Sensor, Motion, LOSS, OFF 5.6.6 RECORD TIME ( 10 SECOND ~ 10 MINUTE ) ► In event occurrence, continual recording time is set. ► In event happening before continual recording time is released, recording time is extended from the point of its occurrence.
5.6.7 POP ‐ UP / ON , OFF ► In event occurrence, the relevant display is enlarged, and popped up to the full display. ► But, in simultaneous event happening more than 2 channels, it is converted to split display mode . 5.6.8 PRE ‐ RECORD / ON , OFF ► When event rerecording is executed, and finished, additional 2‐3 seconds of recording is progressed than the time of set recorded one. ex) If event is triggered at 3:10, it records videos from 3:09: 57. ...
5.7 NETWORK SETUP 5.7.1 IP SETUP IP address can be allocated to PC that is connected to the network 1) IP Type ( STATIC / DHCP / PPPoE / OFF ) Select the type to match user's network environment . 1‐1) STATIC : Fixed IP Type that user directly sets up IP information to DVR that IP service provider allocated. 1‐2) DHCP : Floating IP Type that DVR automatically receives IP by DHCP server. 1‐3) PPPoE : Type that has direct connection with the external without sharing internet (router). User should insert ID, and password IP service provider provides. 1‐4) Not connecting ...
Page 98
2) IP address ( 000.000.000 ) Input IP address that user subscribed ISP (internet service provider) provides. 3) Subnet mask ( 000.000.000 ) Input the address of subnet mask ISP (internet service provider) provides. 4) Gateway ( 000.000.000 ) Input the gateway address ISP (internet service provider) provides. 5) COMMAND PORT ( 9201 ) In computer connection, port can be changed. Port can appear differently based on the set up of the relevant network status (like fire‐wall, etc.). The factory default is set in 9201 for port. 6) VIDEO PORT ( 9202 ) It is needed for video transmission by network. 7) WEB PORT ( 80 ) It is needed for monitoring by internet explorer without client software program. (Net viewer). 8) PPPoE ( PASSWORD / ID ) Input password, and ID ISP (internet service provider) provides ...
5.7.2 DDNS 1) DNS IP ( 000.000.000.000 ) 2) URL VIDEONETSERVER.COM Input DNS IP address. In manufacturer's DNS use, URL is used for default value. 3) PORT ( 20000 ) Input DNS URL. In manufacturer's DNS URL use, port can be used for default values. 4) IP RENEWAL ( 10 MINUTES / 20MINUTES / 30MINUTES ) Input the allocated port to DNS server. DVR itself makes sure of unusual status of IP every set time. ...
5.7.3 E‐MAIL 1) SEND E‐MAIL ( YES / NO ) _______@__________com In EVENT happening, insert e‐mail address to send the relevant display. 2) SMTP SERVER In sending E‐ mail, insert SMTP & DNS server. 2‐1) TYPE DEFAULT / USER 2‐2) NAME KORNET.NET 2‐3) PORT 25 2‐4) ID ******** 2‐5) PW ******** ...
3) PERIOD ( ONCE / EVENT / OFF ) In sending e‐mail, user has to decide if, or not he will send event occurrence at one time per day, or whenever event occurs. 4) TEST Possible to transmit just happening event for test. 5.7.4 DVR NAME ( DVR ) Input each ID to separate each DVR that gets access to CMS. 5.7.5 DVR LOCATION ( DVR01 ) Input the location to display DVR position respectively that gets access to CMS. ...
5.8.3 USER SETUP User can set up the right of DVR management by user. 1) ADMIN SETUP Admin mode has the authority to ►ID xxxxxxxx set up, and release all of functions for DVR. ►PASSWORD xxxxxxxx ...
Page 105
2) USER SETUP ►USER USER 1 ~ USER 3 ►ID xxxx ►PASSWORD xxxx ►AUTHORITY ►SETUP ON / OFF ►SEARCH ON / OFF ►BACKUP ON / OFF ►REC OFF ON / OFF User mode is entitled to set up, and release some functions of DVR. According to adminstrator's purpose, it can limit the controlling authority of users. ...
5.8.4 HDD FORMAT As HDD formatting function, be sure to check it in order to prevent the deletion of HDD record data. In case of selecting YES, format starts. NOTE In HDD format execution, the current data in HDD are all deleted. So, check once again execution status before it.
5.8.5 CONTROLLER To set up interface used for external controller. 1) RS‐232 ► BAUDRATE 115200 ► DATA BIT 8 BIT ► PARITY NONE ► STOP BIT 1 BIT 2) RS‐485 ► BRAUDRATE EACH ► DATA BIT 8 BIT ► PARITY NONE ► STOP BIT 1 BIT 5.8.6 SYSTEM LOG As a menu to check all data for DVR use, user can check such acceptable data as menu access, manual record, switch on/off, network, back up, and search.
5.8.7. INFORMATION Press info button, it shows the information on HDD/DVD/USB connected to ►HDD brand, and manufacturer ►Total capacity of HDD ( Recorded capacity display ) ►Feasible capacity for HDD recording Press up & down button and move to next page. ►Network IP and Mac address ►Current software version ...
Page 109
To exit from this menu, press INFO button again. ►USB Model No. ►DVD RW Model No. ...
5.8.8. RESET As a menu to initialize DVR system, it is changed into factory default for all setting values user set up. 1) FACTORY RESET ( YES / NO ) In case of pressing YES button, initialization starts. 2) SET ‐ VALUE COPY ( YES / NO ) In setup of various DVR identically, user can copy one DVR setting values, and insert the same input values. 3) SET ‐ VALUE LOAD ( YES / NO ) By executing setting values copied, user can repeatedly insert the same setting values to various DVRS. NOTE For some problem on our DVR, copy the setting values, and back up it in USB. And then send the stored USB to our e‐mail, prompt action will be taken.
5.9 UPDATE User can update DVR system with new firmware easily by USB and network. DVR system update should be available only in condition that HDD is connected to DVR properly. 5.9.1 USB UPDATE ▌Firmware download from Web Hard Go to www.webhard.net and log‐in. ID:kprotech / PW: kpro1234 / Location : Download only Download new firmware file and unzip it. Create "update" folder (small letter) in USB memory stick and copy "dvr‐2008‐12‐10 (firmware file)" & "crc_check.txt" to the folder. Insert USB memory stick into DVR and update DVR with new firmware. (Main menu > Update> Device ‐ USB > Yes) ...
Page 112
▌Firmware download from Internet Explorer Type in the address below on internet explorer. Do not change any letter and input it as it is. HTTP://videonetserver.com/UPGRADE‐MH/kpro/dvr.zip Unzip downloaded file from the address and three files appears. [Firmware file] [Firmware size check program] [Firmware size indicator file] A. Open "crc_check.txt"first and check firmware file size. (ie. D4C4E536) . Install "CheckCRC" program. B. Click "Select File" button and select firmware file. C. It shows the file size (ie. D4C4E536). The file size of every firmware version has its own size. When the size is same as one of firmware file, full size of firmware is downloaded properly. If there is a discrepancy, you have to try to download it again. Create "update" folder (small letter) in USB memory stick and copy the firmware checked by "CheckCRC" program into the folder.
Insert USB memory stick into DVR and update DVR with the new firmware. ( Main menu > System update > Device‐ USB > Update ‐ Yes) NOTE Firmware download from "Web Hard" is recommended. 5.9.2 NETWORK UPDATE For network update, DVR should be connected into internet line. NOTE It may fail due to user's Internet environment. In this case, USB update (by Web Hard download) is recommend. ...
Update DVR by network. (Main menu > System update > Device ‐ network > Update ‐ Yes) It normally takes 4 ~ 6 minutes. 5.9.3 UPDATE In system update menu, it shows current firmware version and new one. ►OLD S/W : it means current firmware version. ►NEW S/W : it means new firmware version to update. ...
MULTI NET VIEWER PROGRAM 6.1 DEFINITION Net Viewer is a client software program that makes users operate DVR (monitor, playback, and backup) remotely through network. Please kindly read out this manual thoroughly for set up, and proper operation. 6.2 NET VIEWER SETUP 6.2.1 INSTALLATION Insert program CD in the package into CD(DVD)‐ROM in your PC and double click the icon ( NetViewerM4H.EXE ) below. Press 'Next' button...
Page 117
Press 'Finish' button. After the installation, you can see the icon on the wallpaper as left. Along with the icon on the wall paper, Net Viewer program is registered in "All Programs". ...
6.2.2 PROGRAM REMOVAL (1) Program removal by Setup.exe Double click the icon of Setup.exe. Select "Remove" and press "Next" button. Select "Y" button. ...
Page 119
Click "Finish" button and Net viewer is uninstalled. (2) Program removal by Window's Program additional and removal ...
6.2.3 NETVIEWER FUNCTION Double click the icon and the program is displayed on screen as follows.
Page 121
CONNECT IPS LIST SETUP LIVE/PLAYBACK PTZ CONTROLL NETWORK SPEED DISPLAY DIV ZOOM FOCUS PLAY CHANNEL CONNECT AUDIO ON/OFF CONNECT LED MICRO PHONE CONNECT SETUP Click "Setup" button in red square and system setup menu is displayed as follows.
Page 122
DVR Name : Input DVR name. IP address : Input DVR IP address or Host Name (MAC address). MAC address is defined as the last 6 digits of Host Name. i.e.) 000001.videonetserver.com ID : Input the ID registered in DVR. cf) Default ID : 00000000 / PASSWORD : 00000000 Password : Input DVR password Command port : Open "9201" from router. Video port : Open " 9202" from router. Avi save directory : Select directory location that Avi file is saved in. ADD & MOD : Add or modify setting values. Delete : Delete IP address. Cancel : Get out of setup menu. Upgrade : Upgrade program version. Group setup Transmission speed limit: Limit max. display speed according to graphic card specifications. Avi save speed : Adjust frame speed for Avi file play. ...
Page 123
2) Login : Make sure of setup values saved in setup menu and press "OK" button. [CONNECT] [DISCONNECT] Click ...
Page 124
How to set up IP router (Model : ZIO / INB5241SRe) NOTE Each IP router had its own setup method. Please refer to manual for details.
Page 125
3. Key in Default Gateway number in the Internet address bar. (e.g.) 192.168.1.1) 4. You can see the window of ZIO / INB5241SRe. ...
Page 126
5. Select "NAT" button. 6. Click "Virtual server setup and input the IP address registered in DVR in "port forwarding" menu. * Name : Input DVR name * IP address : Input the IP address registered in DVR * Protocol : TCP * External port : 9201 (Default) (It should be same as the port number set in DVR.) * Internal port : 9201 ...
Page 127
7. Click "Add" button and the list is displayed as below. 8. Press "Save" button and the values are saved. 9. Conduct port forwarding of the port number 9202 by following steps as above ...
Page 128
NOTE When monitoring DVR via web viewer, web port should be open. The setup method is same as above. Default is 80. 3) Direct Logon : When double clicking one of DVRs registered in tree view, the DVR is connected and displayed automatically. In case that many DVRs are registered, tree view is dropped down when clicking one DVR registered. The connected DVRs (Max. 5)
Page 129
When double clicking one of DVR lists registered on AUTO DEF_DVR, the DVR is moved to CONNECT_DVR. cf) AUTODEF_DVR : The DVR lists registered by SETUP menu. CONNECT_DVR : The DVR lists connected currently out of registered DVR lists. * AUTODEF_DVR >= CONNECT_DVR * When connected properly, Live mode is appeared autom atically. NOTE Max. 4 DVR IP addresses can be connected at same time. The transmission speed may be different according to user's computer specification. ▮LAN : LAN DVR search ‐It shows that all DVRs connected currently through LAN by pressing Search Dvr button. ‐"End Search.." appears when DVR search process is finished. ‐ It is useful for dynamic LAN environment. CUATION This function may be limited on LAN or PC protected by firewall.
Page 130
WAN : WAN DVR search DVR communicates with DNS server (default : videonetserver) every 10 minutes. ‐ 2008‐1‐16 13:43:18 : Last time to communicate with DNS server ‐ 0c0024.videonetserver.com : host name (MAC address) ‐ 121.192.157.247 : WAN IP of current connected DVR GET : it shows all users connected currently through WAN by pressing Find User button.
Page 132
PLAYBACK mode Click Press red circle and select "PLAYBACK". Click Click "Time" button in PLAYBACK mode. Click "Open" button and search menu is displayed as below. ...
Page 133
A. Select the month as you want. B. Select the date. C. Select the time. The time bar is appeared in the bottom of search menu, showing recording data in yellow. (Gray part means no recording data.) D. Select minute and second in details as you want by clicking up/down buttons. E. Click "OK' button and the data is played. PLAY speed control PLAY STOP/PAUSE Fast forward Reverse play Play by frame (in pause mode only) Reverse play by frame (in pause mode only) ...
Page 134
BACKUP Recording date can be archived in PC for data backup. Press backup button and the lists are appears. Select the list for backup as you want. Select "Save directory". Click "backup" button. Backup is activated. Backup file is archived in PC.
Page 135
* How to play backup file Select File Play mode. Press OPEN button. Select BACKUP file. Backup file is played. NOTE Backup file can be played on window media player without net viewer program. But, it is played each 1 channel. Backup file is played through file viewer without net viewer program. ...
Page 136
How to convert to AVI file When live video or record file is converted to AVI file format, it is played on window media player without Net viewer program. A. AVI file save directory setup Set save directory as you want like C: \. B. Activation Select a channel as you want and click AVI icon as below. To release, press it again. [Before save] [saving] [Stop save] AVI conversion is on. C. File play Double clicking the converted file and it is played on Window Media Player directly. ...
Page 137
UPGRADE User can update software version easily just by clicking one button. Click Click Press Upgrade Net viewer button on setup menu and version upgrade starts automatically. After the process, new version is activated on screen. ...
Page 138
LOG LIST It shows all of DVR log lists generated by system reboot, shutdown, menu setup, network login, network logout and so on. Network user connect Menu setup System Reboot Still image save...
Page 139
[16 div Mode still image] Select display div mode(1,4,6,9,16Div). click button. For image save on PC, press save button and for image print, pr ess print button. Remote Control It can offer user to adjust menu values remotely. REROAD : It reads out menu values from DVR set. SET CONFIG : Adjusted values by net viewer apply to remote DVR set. ...
Page 140
Q.SET UP : Q.menu setup CAMERA INFO : camera setup DISPLAY : display setup RECORD‐SETUP : recording setup EVENT : event setup NETWORK : network setup DVR‐INFORMATION : system information PTZ control User can remotely control PTZ camera on Net Viewer. 1) PAN / TILT : Control PTZ camera to up/down/left/right direction. 2) Zoom / Focus ...
6.3 WEB VIEWER It offers user to have an access to DVR by network in Internet Explorer (IE) directly for his monitoring and playback. 6.3.1 MAC ADDRESS ON IE (INTERNET EXPLORER) ‐ Type in MAC address of DVR on IE (Internet Explorer). ‐ You can check MAC address in INFO menu by pressing INFO button in live mode. ‐ Mac address consists of "6 digits (the last 6 digits from MAC address)" . videonetserver . com" i.e) http://0c0024.videonetserver.com ...
IP ADDRESS: Type in MAC address ( ie) 0c0024.videonetserver.com) ID : Input DVR ID (default : 00000000) PASSWORD : Input DVR password (default : 00000000) PORT : Type in 9201 as CMD port (default) and 9202 as Video port (default). Press "OK and live mode appears on Net Viewer. 6.3.2 PLAY BACK...
1. Press "PLAYBACK" button and playback menu appears. 2. Type in date and time as want. 3. Press "OK" button and recording data is played. 6.3.3 MULTIPLE DISPLAY Single channel mode Click channel number or double click the channel directly and it converts to single channel mode. Various screen mode User can move to various screen modes like 4,6,8,9,10,13,16 channel mode. Click the icon and it convert to the screen mode accordingly. Playback speed controll...
TROUBLE SHOOTING 1. The system power is turn off. Check if power cable is correctly connected . Check if input voltage is correct. If the system power does not turn on while power cable is correctly connected, please contact the supplier, or manufacturer. 2. The system power is turned on, but no video is displayed on the monitor. Check if the monitor power cable is properly connected. Check if the monitor is turned on. Check if the video output cable of the DVR is properly connected to the monitor. Unplug the power cable, and plug in again. 3. The camera numbers are displayed on the screen, but the camera images not displayed. Check if the camera video output is correctly connected to the DVR system. Check if the power cable is correctly connected on the camera. Check if the video cable is working well , or not, which is connected to system from camera. When video is connected with various systems, weak video signal causes this kind of problem from video distributor. In this case, the direct connection with video of relevant camera will find the solution by solving this matter. Turn off DVR system, and turn it on again. 4. The camera video is shown on the screen, but the system doesn't record video. Check if it is set to "NONE" in the record mode of the record setting mode. Turn off the DVR, and turn it on again.
Page 145
5. Impossible to search for the recorded video. Check if there is a recorded video data when you are trying to search for on the table. If there is no recorded video data, check if it is set to "NONE" in the record mode of the recording setting. 6. The audio data is not played in recorded video data. Check if audio record option is correctly set to the camera you wish to record audio. Check if audio mute is enabled. Check if microphone ,and speaker port are correctly connected on the rear of DVR system. Check if the connected microphone is properly working. Check if the connected speaker is properly operating. 7. The color of videos are strange, or video is shown abnormally. Check if the camera connected to the system has a problem. Check if the camera is not damaged by inserting abnormal camera No. and normal video camera video No. in replacement. Check camera No. Check if the video system setting is the same as your camera system. Depending on your area, the camera system can support either PAL, or NTSC. Relying on the camera video transmission system, video process differs greatly. At this state, video is seen, but hard to recognize it normally. 8. There are much (screen) noise on the image. Check if the video signal output has the problem from camera. Check if the camera is not damaged by inserting another camera into the working video output in replacement. ...
Page 146
Check if it is cut, or cross‐wired, or shortened for the video cable to connect the camera ,and the DVR. Check if there is a high voltage wire around the video cable connecting the camera to the DVR system. It can cause the noise problem to decrease video quality. Check if it is correct for the video cable to connect camera to the DVR system. When a normal power‐supplying cable is used instead of the video cable, screen noise can be generated. 9. Sometimes system itself restarts. System itself can restart due to watchdog function when any problem occurs to the DVR. 10. The connected sensor is not working. Check if the type of sensor in event setup menu is the same as the connected sensor. Check if system is set to use the sensor in record schedule window from the recording setting menu. Check if power cable of the sensor is properly connected. Check if signal cable of the sensor is properly connected.
WARRANTY The quality of this product is guaranteed by strict quality control processes, and testing. If the product becomes non‐operational, the warranty may be in operation. The warranty period is valid for 1 year from the date of purchase. WARRANTY GUIDE * Check the Product Warranty Sheet to make sure it is still in effect. • Check the problem again, and contact the supplier, or manufacturer you purchased DVR unit from. • About product repair, exchange, or refund, we follow the "compensation regulation for customer's loss" announced by "the Economic Planning Board". (Korea only) WARRANTY If the product becomes non‐operational, the warranty may be in operation. The warranty period is valid for 1 year (s) from the date of purchase. Service fee, and replacement parts will be charged in below cases: 1. Damaged the user's carelessness. 2. Damaged due to a natural disaster. 3. Damaged due to the user not following the instructions, and cautions written in the user's guide. 4. Damaged due to incorrect power voltage, and/or frequency being used. 5. If the Product Warranty sheet is expired. 6. Damaged due to an engineer not employed by supplier, or manufacturer modifying the system. ...
Page 148
If your system is damaged after the expiry of the warranty period, free repair service will not be available. If you wish the system to be repaired, service fee, and replacement parts will be charged. PRODUCT WARRANTY Product / Model Serial Number Purchasing Dealer Purchasing Date Warranty Period year (s) from the purchasing date. Name Customer Address The Product Warranty Sheet will not be issued again. The Product Warranty Sheet must be filled on the same day as the product's purchase. This document must be shown in order to receive the free repair service. ...