Related Manuals for Elan PZ6 Series II
Summary of Contents for Elan PZ6 Series II
- Page 1 S S Y Y S S T T E E M M P P R R E E C C I I S S I I O O N N P P A A N N E E L L - S S e e r r i i e e s s I I I I INSTALLATION MANUAL...
- Page 2 —The appliances should be connected to a power supply only of the type described in the operating instructions or as marked on each appliance. If you are not sure of the type of power supply to your home, consult your authorized ELAN dealer or local power company.
- Page 3 —Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning. Do not use a telephone to report a gas leak if the leak is in the vicinity of the ELAN electronic equipment because of risk of fire or explosion.
-
Page 4: Table Of Contents
Door Speaker Assembly Connections........11 Relay Connections.............12 Volume Control Override Connections......12,13 Z•880 Connections.............14 Z•Series Amplifier Connections..........15 Quick Reference Guide – Front Panel ........16 Quick Reference Guide – Rear Panel........17 Warranty ..................18 © ELAN Home Systems 2002 • All rights reserved. 3/02 Page iii... -
Page 5: Introduction
INSTALLATION MANUAL Series II NTRODUCTION The PZ6 Precision Wall Plate was created to make the installation of ELAN Z•Series Multi-Source/Multi-Zone systems literally 'plug-and-play'. Like the entire family of ELAN Essentials products, the PZ6 was designed with the cus- tom installer in mind. Its goal––to cut hours off of every Z•Series installation and assure that all system wire runs and Z•... -
Page 6: Z• Series Wire Runs
E L A N H O M E S Y S T E M S INSTALLATION MANUAL Series II ERIES © ELAN Home Systems 2002 • All rights reserved. 3/02 Page 2... - Page 7 The PZ6 frame is equipped with four "winglets" which, when tightened, clamp the frame securely against the rough-in bracket or, in retrofit applications, against the drywall. © ELAN Home Systems 2002 • All rights reserved. 3/02 Page 3...
-
Page 8: Connections
See pages 7-13 for detailed System Connections. ONNECTIONS INTERCONNECT C C ABLES ELAN now carries a variety of interconnect cables for use with the PZ6 as well as other Audio/Video applications © ELAN Home Systems 2002 • All rights reserved. 3/02... -
Page 9: Pin Out
24 or 22 AWG solid con- ductor wires. Use of a 110 punchdown tool is recommended. NOTE: The PZ6 also comes with Punchdown caps to ensure that wiring connections won’t come loose. © ELAN Home Systems 2002 • All rights reserved. 3/02 Page 5... - Page 10 The PC Board Silk Screen gives you the exact name-by-name connection for each wire The COLOR-CODE Overlay gives a color-coded reference for Z•PAD and Door Speaker Assembly connections © ELAN Home Systems 2002 • All rights reserved. 3/02 Page 6...
-
Page 11: Punchdown Connectors
VC+ and VC- wires that enable Page and Doorbell override control. Use two of the remaining conductors from the CAT-5 keypad wire run (Orange for VC+ and White/Brown for VC-) to make this connection. © ELAN Home Systems 2002 • All rights reserved. 3/02 Page 7... -
Page 12: Z•630 Preamp Controller Connections
Z•600 to the jack labeled RELAY on the front of the PZ6. CONTROL - The CONTROL interface must be made when you are using ELAN Volume Controls with Override. Using a RJ45-to-RJ45 interconnect cable (ELAN C4545 1M or 2M), connect the jack labeled CONTROL OUTPUTS on the Z•600 to the jack labeled... -
Page 13: Door Speaker Assembly Connections
There are two punchdown connectors on the back of the PZ6 for the connection Use the color-code of ELAN Door Speaker Assemblies (labeled DOOR SPEAKER 1 & DOOR overlay to ensure cor- SPEAKER 2). The Z•600 may access each of the door stations independently. -
Page 14: Relay Connections
USING THE Z•600 COMM CONTROLLER'S INTERNAL POWER SUPPLY FOR OVERRIDE CONTROL A maximum of 5 ELAN volume controls with override may be powered using the Z•600's internal power supply. If additional volume controls with override are to be utilized, an external +12VDC power supply (ELAN Z•027) will be required (see next page). - Page 15 The Z•027 connects to the jack on the front of the PZ6 labeled "VCO". Plugging a power supply into the VCO jack automatically disconnects the Z•600's internal power supply. NOTE: As many as 32 ELAN Volume Controls with Override may be powered by a single Z•027. CONNECTING MORE THAN FOUR VOLUME CONTROLS WITH...
- Page 16 Z•880 V V IDEO C C ONTROLLER C C ONNECTIONS FRONT PANEL CONNECTIONS 1. Using a RJ45-to-RJ45 interconnect cable (ELAN C4545 1M or 2M), con- nect the jack labeled NETWORK/IR INTERFACE on the back of the Z•880 to the jack labeled Z•880 on the front of the PZ6.
-
Page 17: Z•Series Amplifier Connections
PZ6. Make sure each speaker is connected to the appro- priate amplifier channel for that room. Once again we recommend the use of ELAN BLACKJACK Banana Plugs to reduce the possibility of loose wire strands causing shorts. - Page 18 Z 630 system with a Z 600 Comm Controller, PZ6 #2’s Z 600 RJ45 jack inputs are not used. • 630 #4 (Zones 10-12) © ELAN Home Systems 2002 • All rights reserved. 3/02 Page 14...
- Page 19 RS485 data bus connections (circled) may be used to link the first PZ6 to the second PZ6. PZ6 #2 GROUND P & DB © ELAN Home Systems 2002 • All rights reserved. 3/02 Page 15...
- Page 20 E L A N H O M E S Y S T E M S INSTALLATION MANUAL Series II UICK EFERENCE UIDE FRONT P P ANEL C C ONNECTIONS © ELAN Home Systems 2002 • All rights reserved. 3/02 Page 16...
- Page 21 E L A N H O M E S Y S T E M S INSTALLATION MANUAL Series II UICK EFERENCE UIDE REAR P P ANEL C C ONNECTIONS © ELAN Home Systems 2002 • All rights reserved. 3/02 Page 17...
-
Page 22: Limited Warranty
Except as may be expressly provided and authorized in writing by ELAN, ELAN shall not be sub- ject to any other obligations or liabilities whatsoever with respect to equipment manufactured by ELAN or services rendered by ELAN.