Table of Contents
Advertisement
E L A N
H O M E
S Y S T E M S
C
ONNECTIONS
NOTE: If two PZ6's will be used
to accommodate a multiple
Z•630 system, all Z•600 con-
nections are made to the first
PZ6 only. See diagram on fol-
lowing page.
© ELAN Home Systems 2002 • All rights reserved. 3/02
-
.
CONT
Z•630 P P REAMP C C ONTROLLER C C ONNECTIONS
PZ6 FRONT PANEL CONNECTIONS
SINGLE Z•630 (3 ZONE SYSTEM)
Using a RJ45-to-RJ45 interconnect cable (ELAN C4545 1M or 2M), connect the
jack labeled IR INPUTS on the back of the Z•630 to the jack labeled Z•630
Zones 1-3 on the front of the PZ6.
DUAL Z•630 (6 ZONE SYSTEM)
1. Using a RJ45-to-RJ45 interconnect cable (ELAN C4545 1M or 2M), connect the
jack labeled IR INPUTS on the back of Z•630 #1 (Zones 1-3) to the jack labeled
Z•630 Zones 1-3 on the front of the PZ6.
2. Using a RJ45-to-RJ45 interconnect cable (ELAN C4545 1M or 2M), connect the
jack labeled IR INPUTS on the back of Z•630 #2 (Zones 4-6) to the jack labeled
Z•630 Zones 4-6 on the front of the PZ6.
MULTIPLE Z•630 (9 OR 12 ZONE SYSTEM)
Using a RJ45-to-RJ45 interconnect cable (ELAN C4545 1M or 2M), connect the
jack labeled IR INPUTS on the back of Z•630 #3 (Zones 7-9 ), to the jack labeled
Z•630 Zones 1-3 on the front of the SECOND PZ6. Repeat for Zones 10-12
(Z•630 #4) and connect to the jack labeled Zones 4-6 on the SECOND PZ6.
Z•600 C C OMM C C ONTROLLER C C ONNECTIONS
PZ6 FRONT PANEL CONNECTIONS
There are six RJ45 connections for the Z•600 Comm Controller: TELCO, PHONE,
RELAY, CONTROL, DS1, and DS2.
PHONE SERVICE CONNECTIONS - Using RJ11-to-RJ11 interconnect cables, connect
the jack labeled TELCO IN on the Z•600 to the jack labeled TELCO on the PZ6; and the
jack labeled PHONE OUT on the Z•600 to the jack labeled PHONE on the PZ6.
RELAY - The RELAY interface must be made if any of the four telephone-activated con-
tact closures that accessible via the Z•600 are to be utilized. Using a RJ45-to-RJ45
interconnect (ELAN C4545 1M or 2M), connect the jack labeled RELAY 1-4 OUTPUTS
on the Z•600 to the jack labeled RELAY on the front of the PZ6.
CONTROL - The CONTROL interface must be made when you are using ELAN Volume
Controls with Override. Using a RJ45-to-RJ45 interconnect cable (ELAN C4545 1M or
2M), connect the jack labeled CONTROL OUTPUTS on the Z•600 to the jack labeled
CONTROL on the PZ6.
DS1/DS2 - The Z•600 provides independent access to 2 ELAN Door Speaker
Assemblies. Using RJ45-to RJ45 interconnect cables (ELAN C4545 1M or 2M), connect
the jack(s) labeled DOOR SPEAKER 1 and DOOR SPEAKER 2 on the back of the
Z•600 to the corresponding jack(s) labeled DS1 and DS2 on the PZ6.
INSTALLATION MANUAL
Series II
Page 8
Advertisement
Table of Contents
