Advertisement
7. Basic configurations (menu 1)
1
2
Modification of programme
and temperature settings
User
(from 5 °C to 30 °C)
modification
authorised (default)
authorisation
Modification of programme
not authorised and temperature
settings restricted
(19 °C +/- 3 °C)
8. Advanced configurations (menu 2)
1
2
Correction possible from -5 °C to
+5 °C in increments of 0.1 °C.
Correcting the
temperature
Press the + or - buttons to
measured
modify and press the OK button
to confirm.
Service Interval
Choice of 1 to 365 days
Number of
days before
(default value: 365)
service
9. Return to the factory configuration
1
2
11. Wireless test
2
> 5"
1
... ... ...
The receiver LED should
flash each time a signal is
received (approximately every
5 seconds).
If this is the case, radio
transmission is occurring
properly.
Otherwise,
5
move your transmitter.
> 5"
3
12-hour clock (default)
Time display
selection
24-hour clock
Not authorised
Automatic
summer/winter
Authorised (by default)
mode
authorisation
> 5"
3
Service Interval: display of the time remaining
before mandatory service required. After this time, if
the service has not been done, the operating
temperature setting for heating is fixed (menu 2-03)
and the DHW switches to OFF (unless overridden,
menu 2-04).
Temperature applied after
Service Interval
Temperature
selection
Choice of 5 to 30 °C
Service Interval
(default value: 16 °C)
> 5"
> 5"
3
Press
the button for the menu
you wish to reset and hold
for 5 seconds
(example for menu 1).
12. Technical characteristics
Transmitter TYBOX 817- 827 RF
... ... ...
5"
5"
5"
• Powered by two LR03/AAA 1.5 V alkaline batteries
(supplied), battery life of 2 years for normal use
• Class III insulation
• Clock backup when replacing the batteries:
30 seconds
• Transmission frequency 868 MHz (Standard EN 300 220)
• Class 1 radio equipment (can be placed on the
market and put into service without any restrictions)
• Wireless range: 100 to 300 metres outside,
3
depending on the equipment associated
(the range varies according to installation
conditions and the electromagnetic environment)
• Wireless remote control device
5"
5"
5"
• Dimensions: LxHxD = 80 x 103 x 16 mm
• Protection rating: IP 30
• Storage temperature: -10 °C to +70 °C
4
• Operating temperature: 0 °C to +40 °C
• Installation in an environment with normal pollution
levels
• Attachment with screws or on a base
0
1
4
ONCE
programme
start time
ONCE
programme
end time
+/-
0,1°C
4
Authorised
DHW override
time
Anti-seizing
of circulator
pump
10. Deleting wireless associations
4
1
To reassociate the receiver with the transmitter,
refer to the "Wireless association" section.
NOTE: You can manually reset the receiver by
pressing the button of the channel to be initialised
for 10 seconds until the LED flashes rapidly.
5
Receiver RF 827
• 230V, 50 Hz power supply, +/-10%,
• Consumption: 11 VA (P=1.2 W)
• Class II insulation
• Radio frequency 868 MHz (standard EN 300 220)
• Wireless range: 100 to 300 metres outside, variable
depending on the associated equipment (the range
can vary depending on the installation conditions and
the electromagnetic environment)
• Automatic action: 1.C (brownout)
• Storage temperature: -10 °C to +70 °C
• Operating temperature: 0 °C to +40 °C
• Installation in an environment with normal pollution
levels
• Screw mounting (standard Wallplate)
• Contact output 3 A max., 230 V Cos ϕ = 1
• Dimensions: 96 x 96 x 39 mm
• Protection rating: IP 40
12h
0
24h
1
5
6
Setting from 12:00 to 00:00
(default value: 07:00AM)
Setting from 12 noon to 12
midnight
(default value: 11:00PM)
365
5°C
30°C
001
5
6
DHW override after Service
Interval
2, 3 or 4 hours
(default value: 2 hours).
Anti-seizing off (by default)
Anti-seizing enabled (circulator
pump operates for 1 minute
every 24 hours)
> 5"
2
13. Troubleshooting
Nothing is displayed on the room unit screen.
There is no power supply.
Check the batteries.
The receiver does not accept orders from the
transmitter.
• Check the transmission by performing a wireless
test
• Move your transmitter if necessary
• Repeat the wireless association of the receiver
with the TYBOX RF
The
The batteries are low.
Change the batteries, ensuring they are in the
correct position.
During radio association, the device displays:
rAd 1.
This menu is reserved.
Associate the receiver again from the rAd menu.
The heating does not work according to the
required temperature.
If you have a Room Thermostat wired in series
with the programmer, check that this thermostat is
set to maximum.
HH:MM
HH:MM
7
8
9
2h
0
4h
1
7
8
9
> 5"
4
3
5
icon appears.
Advertisement
