Table of Contents
Advertisement
Trimmed material
Distance between the needle axis and the work trimmer line
Power output of the work trimmer motor
Stroke frequency of the work trimmer knife
Stroke range of the work trimmer knife
Length of trimmed thread ends
Input machine with clutch motor
Input machine with stop motor
Equivalent accoustic presser level of the sole machine
at work place by 20% use of the machine during
a shift under standard sewing conditions
Layout dimensions of the machine (including the stand)
Height of the machine (including the stand)
Applicable knives
Table 4
The upper No. in the column - Ordering No. - applies to orders placed ith the company Maier, the lower one for those placed with
Minerva.
Ordering No.
11165 x 2,7 *
S425 311020
11165 x 3,0
11165 x 3,5
S425 311026
11165 x 2,7 HSS
11165 x 3,5 HSS
11165 x 4,0 HSS
11233 x 2,7
S425 311030
11233 x 2,7 HSS
11166 x 2,7
S425 311032
11166 x 3,1
11166 x 3,5
S425 311034
11166 x 4,0
11233 x 2,7 BX lang
= 11178 x 2,7
S425 311036
040188 x 7,0
S425 311037
* supplied as standard
Grinding the work trimmer knife
To obtain due quality of trimming, the knife should be ground on special grinding machines at short intervals (of about 2 to 5
hours) corresponding to the durability of the knife trimmer edge. The special grinding machines are produced by the following
companies:
FORTUNA WIEN GmBH, A-1151 WIEN-Pelzgasse 13, Postfach 91
MAIER UNITAS GmBH, NÜRTINGER Strasse 19, D-7316, KÖNGEN, Postfach 1130
Side of
Height of
trimmer
trimmer (a)
(mm)
(mm)
1 3
2,7
1 3
3,0
1 3
3,5
1 3
2,7
1 3
3,5
1 3
4,0
1 1
2,7
1 1
2,7
1 3
3,5
1 3
2,7
1 3
3,5
1 3
4,0
1 4
2,7
14,5
7,0
can be ordered with Minerva as well
lining of relatively stiff materials - max. 2.5 mm
0.8 - 1.5 mm (according to sewing category)
25 W
3300 strokes/min (constant)
1,2 - 4,3 mm (adjustable)
8 - 11 mm
Max. 700 W
Max. 800 W
82 dB/A
1060 x 550 mm
1680 mm
Illustrations
long cutting edge,
front end turned up
High-speed steel,
long cutting edge,
front end turned up
elbowed version with
short cutting edge,
front end turned up
High-speed steel,
elbowed version with synthetic lining material
short cutting edge,
front end turned up
flat version with
cutout for sewing
long cutting edge
low-elbowed with
long cutting edge,
front end turned up
upward-cutting
4
(600 W with minimotor)
Features
Applications
Tooling steel,
For normal lining
flat version,
material with
cross-sections
For very soft or
flat version,
synthetic linings
material with
cross-sections
Tooling steel,
For normal lining
material with
cross-sections
and tight curves
For very soft or
with cross-sections
and tight curves
Tooling steel,
For normal lining
corners,
Tooling steel,
For normal lining
material with
cross-sections
Tooling steel,
For trimming outer
elbowed,
edges of thick material
to be ordered with the company Maier
material
Advertisement
Table of Contents
