Applicable Signal - Toshiba TLP411E Technical Training Manual

14. APPLICABLE SIGNAL

Quite a signals are used as the applicable signals in the
preset mode (standard value) as shown in table 5-10. For
the signals not fit to the preset modes, a user mode is pro-
vided.
In the preset modes, the applicable signals are based on the
VESA standard, so the sample frequency (CLOCK adjust-
ment in the panel menu) is not used, but the adjustment is
allowed only in the user mode.
Signal
Content
Mode
NTSC NTSC
PAL PAL
V60 VGA 60 Hz
V70 VGA 70 Hz
V70 VGA 70 Hz
V70 VGA 70 Hz
V70 VGA 70 Hz
V72 VGA 72 Hz
V75 VGA 75 Hz
V85 VGA 85 Hz
V85 VGA 85 Hz
V85 VGA 85 Hz
V85 VGA 85 Hz
M13 MAC-13"
24K PC98
S56 SVGA 56 Hz
S60 SVGA 60 Hz
S72 SVGA 72 Hz
S75 SVGA 75 Hz
S85 SVGA 85 Hz
M16 MAC-16"
USHI XGA 60 Hz 1024
USHI XGA 70 Hz 1024
USHI XGA 75 Hz 1024
USHI XGA 85 Hz 1024
• In the sync column of table 5-8, P shows the positive
polarity and N shows the negative polarity.
Table 5-8 Applicable signal
Resolution All
H V H
664 484 800 525
756 574 800 625
640 480 800 525
720 350 900 450
720 400 900 450
640 350 800 450
640 400 800 450
640 480 832 520
640 480 840 500
640 350 832 445
640 400 832 445
720 400 936 446
640 480 832 509
640 480 864 525
640 400 848 444
800 600 1024 625
800 600 1056 628
800 600 1040 666
800 600 1056 625
800 600 1048 631
832 624 1152 667
768 1344 806
768 1328 806
768 1312 800
768 1376 808
In the user mode, the signal line number is detected to al-
low the separate adjustment in the VGA system (basically
effective for line number of 480/400/350 lines) and SVGA
system (basically effective for line number of 600 lines).
In the user mode of SVGA system, the input signal is ap-
plicable to the plain display mode only in the XGA system
(basically effective for line number of 768 lines) . That is,
the signal is displayed.
Frequency
V H V
15.730 59.940
15.630 50.000
31.470 59.940
31.470 70.020
31.470 70.020
31.470 70.020
31.470 70.020
37.860 72.810
37.500 75.000
37.861 85.080
37.861 85.080
37.927 85.039
43.269 85.008
35.000 66.670
24.830 56.420
35.160 56.250
37.880 60.320
48.080 72.190
46.880 75.000
53.674 85.061
49.720 74.550
48.363 60.004
54.476 70.069
60.023 75.029
68.677 84.997
• In the operation column, O shows a standard mode, D
shows pull-in mode, ¨ shows plain display mode and
X shows the signal is out of correspondence.
5-12
Sync Operation
H/V
Clock Check
12.590 N/N O
12.500 N/N O
25.175 N/N O
∆
28.322 P/N
∆
28.322 N/P
28.322 P/N O
28.322 N/P O
31.500 N/N O
31.500 N/N O
31.500 P/N O
31.500 N/P O
∆
35.500 N/P
36.000 N/N O
30.240 N/N O
21.053 N/N O
36.000 N/N O
40.000 N/N O
50.000 N/N O
49.500 N/N O
56.250 N/N O
57.283 N/N O
65.000 N/N
75.000 N/N
78.750 N/N X
94.500 N/N X
Remarks
Video input
Video input
Plain display
Plain display
Plain display
Plain display