Table of Contents
Advertisement
Quick Links
Installation
The ETN24 is designed for wall mounting in the room to be controlled. It
should be located where the occupant can easily read the LCD display and
use the controls. If the built in temperature sensor is being used to measure
room temperature, the module should be placed where the temperature is
representative of the general room conditions. Cold or warm air draughts;
radiant heat and direct sunlight should be avoided.
General points to follow:
- Disconnect power to the main board before installing the unit.
- The unit should not be installed on an outside wall or where there is an air draft.
- The unit must not be exposed to a direct sunlight.
- The standard height to install this unit is 1.5 meter (5 feet) from the floor.
Installation procedure:
Separate the front panel from back panel by pressing the tongue located in the top of the unit and pull the
back panel out.
Line the back panel up against the wall or flat surface. Install three screws as required.
Make electrical connections as shown on enclosed electrical wiring diagram.
Install the cover to the back panel; first the two tabs on the bottom and then the top tongue.
Push until tight against the wall.
ETN24-SUPER-FP-PROG-F
Owner's manual & Technnician Settings
Tel: (856) 2882882
Tel: +972-3-9626462
Fax: +972-3-9626620
support@meitavtec.com
ºF
o
ON
Su
Cool
Heat
Program: Wake
On/Off
Select
Prog
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for meitav-tec ETN24
Summary of Contents for meitav-tec ETN24
- Page 1 Installation The ETN24 is designed for wall mounting in the room to be controlled. It should be located where the occupant can easily read the LCD display and ºF use the controls. If the built in temperature sensor is being used to measure...
- Page 2 For a heat pump system with one heat element, leave terminal “W2” free. For system with one compressor, leave terminal “Y2” free. RC-RH, - When using one transformer, RC,RH terminals must be shorted. External sensor Connection (option) Important: The external sensor must be Meitav-tec type only! Temp °F Res. KΩ 115.8 100.9...
-
Page 3: Dip Switch Settings
Time temperature*. Normal work Freeze protection *adjustable – please refer to the technician settings section of the operating manual. Tel: (856) 2882882 ETN24-SUPER-FP-PROG-F Tel: +972-3-9626462 Fax: +972-3-9626620 Owner’s manual & Technnician Settings support@meitavtec.com... -
Page 4: Operating Instructions
Lock the thermostat - Press and hold the [Select] button (20 seconds) until "Loc" appears on display. Unlock the thermostat - Press and hold the [Select] button again (20 seconds) until "UnLo" appears on display. Tel: (856) 2882882 ETN24-SUPER-FP-PROG-F Tel: +972-3-9626462 Fax: +972-3-9626620 Owner’s manual & Technnician Settings support@meitavtec.com... - Page 5 Press the [Select] button again to return to normal display Note: The Auto mode can be disabled by technician – please refer to technician settings section in this manual. Tel: (856) 2882882 ETN24-SUPER-FP-PROG-F Tel: +972-3-9626462 Fax: +972-3-9626620 Owner’s manual & Technnician Settings...
-
Page 6: Weekly Program
Repeat for Start Start Sunday time time Point Point Prog Prog Prog Prog “Day”, “Return” & Hours Minutes cool heat “Sleep” Wake Return Sleep Sunday program Tel: (856) 2882882 ETN24-SUPER-FP-PROG-F Tel: +972-3-9626462 Fax: +972-3-9626620 Owner’s manual & Technnician Settings support@meitavtec.com... -
Page 7: Technician Settings
Use the [+] and [-] buttons to adjust the freeze protection cut-in temperature. Range: 43…67°F, Default 47°F. Press the [Select] button again to return to normal display. Cut-off temperature Tel: (856) 2882882 ETN24-SUPER-FP-PROG-F Tel: +972-3-9626462 Fax: +972-3-9626620 Owner’s manual & Technnician Settings support@meitavtec.com... - Page 8 Tel: (856) 2882882 Tel: +972-3-9626462 Fax: +972-3-9626620 support@meitavtec.com www.meitavtec.com...
Need help?
Do you have a question about the ETN24 and is the answer not in the manual?
Questions and answers