Advertisement
Meitav-tec Ltd (Contel group)
Tel: +972 (3) 962 6462 Fax: +972 (3) 962 6620
www.meitavtec.com - support@meitavtec.com
ETN-24-SUPER-PROG
(Europe Program – 5-1-1 – Celsius)
Owner's Manual
Installation and Operating Instructions
Please read this manual carefully before installation and use.
Index
Options and accessories
Dip Switch Configuration and External Sensor Connection
1. Options and Accessories
• Hand held remote control with weekly program.
• External sensor option:
RS01 for remote temperature sensing (1 required)
RS02 for average temperature sensing (2 required)
For details on where to purchase accessories, please contact Meitav-tec for your
nearest location or visit our web site at www.meitavtec.com
File: etn24-super-prog-eu-celsius-rev2.doc | Rev. 2 | 11/11/2009 | B5A7
1
2
3
4
5
6
Advertisement
Table of Contents
Related Manuals for meitav-tec ETN-24-SUPER-PROG-EU Series
Summary of Contents for meitav-tec ETN-24-SUPER-PROG-EU Series
- Page 1 RS01 for remote temperature sensing (1 required) RS02 for average temperature sensing (2 required) For details on where to purchase accessories, please contact Meitav-tec for your nearest location or visit our web site at www.meitavtec.com File: etn24-super-prog-eu-celsius-rev2.doc | Rev. 2 | 11/11/2009 | B5A7...
- Page 2 2. Installation Instructions It is very important to find the right place to install the thermostat. Please make sure to follow all the installation instructions in order to get an accurate reading of the temperature. Separate the front panel from back panel by depressing the tongue located in the top of the thermostat.
- Page 3 3. Wiring Connections Rc-Rh - If one transformer is in use, Rc-Rh must be shorted - (Default from Factory) Table 3.1 - Connections for all applications Terminal Function ETN HC11 HC22 HP21 HP32 24Vac RED (Bridged to RH) 24Vac RED (Bridged to RC) 24VAC Common from transformer Heating 1 Stage / Heat Pump...
- Page 4 4. DIP Switch Configuration Before making any changes disconnect power to the main board. Table 4.1 – DIP Switch Selection Switch Function Default Internal Sensor Control External sensor control Heat Pump (HP) Heat - Cool (HC) Electrical Heat In HC mode: (Switch 2 OFF) Oil/Gas Heat Heat Pump in COOL...
- Page 5 5. External sensor connection - option The external sensor must be Meitav-tec type. Before making any changes disconnect power to the main board. Table 5.1 - N.TC. Sensor: Temperature ~ Resistance Characteristics 10.0 12.8 15.6 18.3 21.1 23.9 26.7 29.4 32.2...
- Page 6 6.3 Mode, Auto Fan • Press the [Select] button – “UnLo” and the actual mode will appear on display. • Using the [+] and [-] buttons switch between: Cool – “Cool” will appear on display Heat – “Heat” will appear on display Emergency heat –...
- Page 7 Important: • While modifying the program you can quickly switch between days by pressing the “On/Off” button. • Press the [Select] button to exit the program. • If no key is pressed for 30 seconds, the thermostat will return to normal display. To modify the Program to your own needs simply follow the steps of the following chart:...
- Page 8 6. Technician Settings Temperature limits and Offset for temperature readings Adjust the set-point temperature for cooling to 10°C. • • Wait until display returns to normal. • Press and hold the [Select] button (6 sec.) – “Cool” will appear on display. •...
Need help?
Do you have a question about the ETN-24-SUPER-PROG-EU Series and is the answer not in the manual?
Questions and answers