Motorola NX-6524 Series Installation Manual

Integrated services platform.
Hide thumbs

Advertising

Advertising

Motorola Solutions
NX-4500/NX-4524/NX-6500/NX-6524 Series
Integrated Services Platform
Installation Guide

Advertising

   Related Manuals for Motorola NX-6524 Series

   Summary of Contents for Motorola NX-6524 Series

  • Page 1

    Motorola Solutions NX-4500/NX-4524/NX-6500/NX-6524 Series Integrated Services Platform Installation Guide...

  • Page 2

    NX-4500/NX-6500 Series Intregrated Services Platform MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions, Inc. 2013. All rights reserved.

  • Page 3: Table Of Contents

    Installation Guide 1.0 Introduction ............5 1.1 Unpacking .

  • Page 4: Table Of Contents

    5.3.1 Turkish WEEE Statement of Compliance ......35 6.0 Motorola Solutions Support Center ....... . . 36...

  • Page 5: Document Conventions

    Installation Guide 1 Introduction The Motorola Solutions NX series integrated services platform provides an innovative and efficient alternative to standard telephony networks. The NX series platform supports both wired and wireless data services for VOIP and video applications for the enterprise branch office marketplace. The NX series platform also provides a framework for scalable branch office services from a centralized network operation center.

  • Page 6: Site Preparation

    Dispose of used batteries according to the instructions. • Motorola strongly recommends the use of an Uninterruptible Power Supply (UPS) that supports the NX-4500/NX6500 series platform power rating. Not using a UPS can result in data loss or equipment damage due to a power surge or power failure.

  • Page 7: Selecting A Site

    Installation Guide • Provide a sufficient number of power drops for your equipment. • Ensure adequate, dust-free ventilation to all installed equipment. • Identify and prepare Ethernet and console port connections. • Verify that cable lengths are within the maximum allowable distances for optimal signal transmission. •...

  • Page 8

    NX-4500/NX-6500 Series Intregrated Services Platform...

  • Page 9: Specifications, Physical Specifications, Environmental Specifications, Electrical Specifications

    Installation Guide Specifications 2.1 Physical Specifications Form factor 2U rack mount Height 3.50in / 88.90mm Width 17.32in / 440.00mm Depth 17.48in / 444.00mm NX-4500/NX-6500 - 19lb / 8.618kg Weight NX-4524/NX-6524 - 23lb / 10.433kg 2.2 Environmental Specifications Operating temperature 32°F to 104°F / 0°C to 40°C Operating humidity 5% to 85% RH, non-condensing Operating altitude...

  • Page 10: Power Cord Specifications, Power Protection

    NX-4500/NX-6500 Series Intregrated Services Platform 2.4 Power Cord Specifications A power cord is not supplied with the NX series platform. Use only a correctly rated power cord certified (as appropriate) for the country of operation. 2.4.1 Power Protection • If possible, use a circuit dedicated to data processing equipment. Commercial electrical contractors are familiar with wiring for data processing equipment and can help with the load balancing of these circuits.

  • Page 11: Led Codes, System Status Leds

    Installation Guide 2.5 LED Codes NX series platforms each have four vertically-stacked LEDs on their front panel. 2.5.1 System Status LEDs SYS 1 LED SYS 2 LED Event System off Amber Solid Green Solid BIOS in progress Amber Solid Amber Solid OS initializing Green Solid Green Blinking...

  • Page 12: Fan Status Led, Temperature Status Led

    NX-4500/NX-6500 Series Intregrated Services Platform 2.5.2 Fan Status LED FAN LED Event System off Green Solid All system fans normal operation Amber Solid System fan failure - system operational System fan failure - ambient inlet temperature is above maximum operating temperature limit Amber Blinking System will be held in reset until the issue is resolved...

  • Page 13

    Installation Guide 2.6 RJ-45 Gigabit Ethernet LEDs Each of the Gigabit Ethernet Ports have two status LEDs. These LEDs display two colors (green and amber), and three lit states (solid, blinking, and off). The tables in the following sections decode the combinations of LED colors and states for the Uplink Ports and Switch Ports LEDs.

  • Page 14: Switch Ports

    NX-4500/NX-6500 Series Intregrated Services Platform 2.6.2 Switch Ports 2.6.2.1 RJ-45 Port Speed LED (Switch Ports GE1-GE24) Port Speed LED Event 10 Mbps Amber Solid 100 Mbps Green Solid 1000 Mbps Amber Blinking Port Fault 2.6.2.2 RJ-45 Port Status LED (Switch Ports GE1-GE24) Port Activity LED Event No link or port disabled...

  • Page 15: Hardware Setup

    Installation Guide 3 Hardware Setup The NX series platform contains the following external interfaces on the front chassis: • (2) RJ-45 Gigabit Ethernet Ports • (1) RJ-45 Serial Console Port • (4) USB Ports (Host 2.0) • (24) RJ-45 Gigabit Ethernet Port Connector (NX-4524 & NX-6524 only) The following figure represents the front of the NX-4500 and NX-6500 models: The following figure represents the front of the NX-4524 and NX-6524 models:...

  • Page 16: Cabling Information

    The sections that follow describe detailed connection and cabling information for each port. For software configuration, please see the current WiNG System Reference Guide available from the Motorola Solutions website at: http://supportcentral.motorolasolutions.com/support/product/manuals.do.

  • Page 17: Gigabit Ethernet Ports, Console Port Setup

    All NX series platforms have (2) RJ-45 Gigabit Ethernet uplink ports and (1) expansion module kit (optional). The NX-4524 and NX-6524 models also have (24) RJ-45 Gigabit Ethernet switch ports. Motorola Solutions recommends using Category 6 Ethernet cable for connections to the RJ-45 ports.

  • Page 18: Usb Devices

    NX-4500/NX-6500 Series Intregrated Services Platform Follow the instructions in the current WiNG 5 System Reference Guide for more information on accessing USB storage devices for file transfers or firmware updates. To add the NX series platform to the network using the WiNG 5 initial settings wizard, see Basic Configuration on page 3.2.2 USB Devices All NX series platforms contain four USB ports for connecting USB flash storage devices to the platform.

  • Page 19: Nx Series Expansion Module

    Installation Guide 3.2.3 NX Series Expansion Module The NX Series Expansion Module kit (KT-NXMODC-01) allows for the installation and implementation of up to four Peripheral Component Interconnect Express (PCIe) cards. The NX Series Expansion Module can be installed in any of the NX-4500/NX-6500 series platforms.

  • Page 20: Rack Mount Instructions

    NX-4500/NX-6500 Series Intregrated Services Platform To install an expansion module: 1. Remove the expansion card cover for the expansion module bay. 2. Insert the expansion module into the expansion module bay. 3. Using a T10 security torque screwdriver, tighten the two screws on the sides of the expansion module to 5.0 lbf-in.

  • Page 21: Verifying The Installation, Supplying Power To The Nx Series Integrated Services Platform

    Installation Guide 3.2.5 Supplying Power to the NX Series Integrated Services Platform To supply power to the NX series platform: 1. Connect an approved power cable to the connector on the back of the platform and plug it into a standard AC outlet with a voltage range of 100 to 240 VAC.

  • Page 22: Basic Configuration

    NX-4500/NX-6500 Series Intregrated Services Platform 4 Basic Configuration Motorola Solutions NX series integrated services platforms running WiNG 5 contain an initial settings wizard to streamline the process of getting the device on the network for the first time. Once the device is installed and powered on, complete the following steps to get the device up and running and access management functions: 1.

  • Page 23

    Installation Guide 6. If this is the first time the management interface has been accessed, the Initial Setup Wizard automatically displays. The Introduction screen displays the various actions that can be performed using the wizard under the Function Highlight field. Use the Choose One type to Setup the Access Point field options to select the type of wizard to run.

  • Page 24

    NX-4500/NX-6500 Series Intregrated Services Platform The Navigation Panel for the Typical Setup Wizard displays the basic configuration options. A green checkmark to the left of an item in the Navigation Panel defines the task as having its minimum required configuration set correctly. A red X defines a task as still requiring at least one parameter be defined correctly.

  • Page 25

    UI to connect to the Access Point, provision its configuration and administrate the Access Point’s configuration. If designating the Access Point as a Standalone AP, Motorola Solutions NOTE recommends the Access Point’s UI be used exclusively to define its device configuration, and not the CLI.

  • Page 26

    NX-4500/NX-6500 Series Intregrated Services Platform 13. The Typical Setup Wizard displays the Network Topology screen to define how the Access Point handles network traffic. 14. Select an Access Point Mode from the available options. • Router Mode -In Router Mode, the Access Point routes traffic between the local network (LAN) and the Internet or external network (WAN).

  • Page 27

    Installation Guide 15. Select Next. The Typical Setup Wizard displays the LAN Configuration screen to set the Access Point's LAN interface configuration. 16. Set the following DHCP and Static IP Address/Subnet information for the LAN interface: • Use DHCP - Select the checkbox to enable an automatic network address configuration using the Access Point’s DHCP server.

  • Page 28

    NX-4500/NX-6500 Series Intregrated Services Platform • DNS Forwarding - Select this option to allow a DNS server to translate domain names into IP addresses. If this option is not selected, a primary and secondary DNS resource must be specified. DNS forwarding is useful when a request for a domain name is made but the DNS server, responsible for converting the name into its corresponding IP address, cannot locate the matching IP address.

  • Page 29

    Installation Guide 19. Select Next. The Typical Setup Wizard displays the RADIUS Server Configuration screen if required. Otherwise, the Typical Setup Wizard displays the Summary and Commit screen. 20. Use the Radius Server Configuration screen to configure the users for the onboard RADIUS server. Use the screen to add, modify and remove RADIUS users.

  • Page 30

    NX-4500/NX-6500 Series Intregrated Services Platform 21. Select Add User to display the dialog to enter user information to add to the RADIUS server user database. 22. Enter the following user information: • Username - Provide a user name used to authenticate the user. •...

  • Page 31

    Installation Guide 28. Select Next. The Typical Setup Wizard displays the Summary and Commit screen to summarize the screens (pages) and settings updated using the Typical Setup Wizard. No user intervention or additional settings are required. Its an additional means of validating the Access Point’s updated configuration before it’s deployed.

  • Page 32: Regulatory Information, Radio Frequency Interference Requirements - Fcc

    This device is approved under Motorola Solutions, Inc. This regulatory section applies to the NX-4500, NX-4524, NX-6500, and NX-6524 platforms. All Motorola devices are designed to be compliant with rules and regulations in locations where they are sold and will be labeled as required.

  • Page 33: Statement Of Compliance

    Installation Guide 5.2 Statement of Compliance Motorola Solutions hereby declares that this device is in compliance with all the applicable Directives, 2004/108/EC and 2006/95/EC. A Declaration of Conformity may be obtained from http://www.motorolasolutions.com/doc. Japan Voluntary Control Council for Interference (VCCI) Class A ITE...

  • Page 34: Waste Electrical And Electronic Equipment (weee)

    NX-4500/NX-6500 Series Intregrated Services Platform 5.3 Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Motorola Solutions for recycling. For information on how to return product, please go to: http://www.motorolasolutions.com/recycling/weee.

  • Page 35: Turkish Weee Statement Of Compliance

    Solutions-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.motorolasolutions.com/recycling/weee. Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola Solutions til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.motorolasolutions.com/recycling/weee. Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται...

  • Page 36: Motorola Solutions Support Center

    • Model number or product name • Software type and version number Motorola Solutions responds to calls by e-mail, telephone, or fax within the time limits set forth in support agreements. If you purchased your product from a Motorola Solutions business partner, contact that business partner for support.

  • Page 37: Nx-4500/nx-6500 Series China Rohs Compliance

    Installation Guide 7 NX-4500/NX-6500 Series China RoHS Compliance...

  • Page 38

    NX-4500/NX-6500 Series Intregrated Services Platform...

  • Page 39

    Installation Guide...

  • Page 40

    Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2013 Motorola Solutions, Inc. All Rights Reserved.

This manual also for:

Nx-6500 series, Nx-4524 series, Nx-4500 series

Comments to this Manuals

Symbols: 0
Latest comments: