Dimplex PF2325 Service Manual page 4

→ Activated by pressing the corresponding button on the
remote or "waving" in-front of the gWave
turn on and wave down to turn off.
• When On the flame effect is visible in the unit.
3 . Heat On/Off:
Turns the heater On or Off.
→ Activated by pressing the corresponding button on the
remote or holding your hand in-front of the gWave
seconds.
• Indicated by the icon and intake temperature being illumi-
nated on the Floating Display™ and the heater turning On
or Off.
!
NOTE: The heater can be operated when the flame is
not visible. In this case the
ing Display™ until the heater is turned off or the flames are
turned back on.
4 . Temperature Down:
→ Adjusted by repeatedly pressing the corresponding but-
ton on the remote.*
• Indicated by setpoint temperature on the Floating Dis-
play™ decreasing and the speed of the fan decreasing to
reduce the amount of heat being projected into the room.**
5 . Temperature Up:
→ Adjusted by repeatedly pressing the corresponding but-
ton on the remote.*
• Indicated by the setpoint on the Floating Display™ in-
creasing and the speed of the fan increasing to increase
the amount of heat being projected into the room.
* The first time the button is pressed the current tempera-
ture set point will be displayed for 5 seconds.
** The temperature can be adjusted from 5 °C to 30 °C (41
°F to 86 °F).
!
NOTE: Pressing the
and °F.
6 . Eco:
Runs the heater in a reduced wattage range
when activated.
→ Adjusted by pressing the corresponding button on the
remote when the heater is on.
• Indicated by the icon being illuminated on the Floating
Display™ and the speed of the fan will decrease propor-
tionally.
7 . Boost:
Turns On/Off the heater boost function.
Runs the unit at the full rated wattage.
→ Activated and adjusted by repeatedly pressing the cor-
responding button on the remote.
• Indicated by the heater running at full heat, for a prede-
termined amount of time, to quickly heat up a cold room/
space. The Boost can be set for a maximum of 20 minutes,
in 5 minute increments.
8 . Multi-Fire XD™:
media theme color presets for the media, flame base
and top lights.
4
- wave up to
TM
TM
icon will remain on the Float-
Decreases the heat output.
Increases the heat output.
then will toggle between °C
Scrolls through the different
→ Changed by repeatedly pressing the corresponding but-
ton on the remote.
• Cycles through the different preset ambient lighting set-
tings of the unit, this includes different combinations of
colours of the top lighting, flame base and media lighting (if
applicable).
!
NOTE: The last option is a personalized colour setting
for 3
("P"), where using the buttons on the remote the lighting of
the unit can be adjusted to any shade of any colour. The
initial setting is no light (Red=0, Blue=0, Green=0) and can
be adjusted, while the display is flashing, by pressing the
outlined buttons (below) to adjust the tones.
Red Tones:
Green Tones:
Blue Tones:
9 . Brightness:
in the unit.
→ Adjusted by repeatedly pressing the corresponding but-
ton on the remote.
• Indicated by the second digit on the Floating Display™
changing to show: "A" (high), "b" (low), "C" (high with media
flicker) and "d" (low with media flicker).
!
NOTE: Media flicker is not an option on the Multi-Fire
XD™ levels 5, 6 or P.
10 . Sleep timer:
duration (from 30 minutes (0.5h) to 8 hours, in ½ hour
increments).
→ Activated and adjusted by repeatedly pressing the cor-
responding button on the remote.
• Indicated by the Floating Display™ changing to indicate
30 minutes (0.5 h) through 8 hours. The fireplace will
automatically turn off when the sleep timer reaches zero
minutes. The sleep timer can be cancelled at any time by
pressing the sleep timer button repeatedly until the sleep
timer will no longer be visible.
11 . Numerical Display
→ Default display will be the heater air intake temperature
or settings (eg. Multifire XD, Brightness, etc.)
Disable Heat
If desired, depending on the season, the heater on the unit
can be disabled. The unit will operate in the same fashion,
with remainder of the controls.
Pressing the
When in the heat disable mode, the temperature reading/
setting on the On Screen Display
!
NOTE: The heater will not work when the unit is con-
trolled with gWave either.
Checking Software Level
The revision can be checked by press
same time.
increase and the decrease.
increase and decrease.
increase and decrease.
Changes the brightness of the lights
Turns the unit off after a preset
then will enable or disable the heater.
displays nothing ("--").
TM
and at the
www.dimplex.com