TABLE OF CONTENTS Table of Contents........3 • Introduction ........... 4 • Package Contents......... 5 • Model Features ........6 • Adjusting and Positioning • Your Collar for Proper Fit ...... 7 Parts and Functions ......8 • Batteries..........13 •...
INTRODUCTION Congratulations and thank you for purchasing our EZT plus 5000/5002 Super Trainer Beeper Training Collar. The EZT series represents the absolute latest technological advancement in the Electronic Dog Training World. It offers Maxx- Range™, the industry’s only internally woven antenna in the collar.
PACKAGE CONTENTS • Transmitter • Collar Receiver (two for EZT plus 5002) • 4” Antenna for the Transmitter • Rechargeable Batteries for both the Collar and Transmitter • Battery Charger • Double Jack Cable for simultaneous charging • Test Light •...
MODEL FEATURES EZT plus 5000, EZT plus 5002 • Digital Technology • One mile range trainer • Beeper/Locator audible from 450 yards away • Lightweight, compact collar and transmitter • 16 adjustable intensity levels of Momentary (‘Nick’) Stimulation, and Constant Stimulation •...
ADJUSTING & POSITIONING YOUR COLLAR FOR PROPER FIT Proper collar tightness and position are very important to insure safety and correct functioning every time you use the collar. • All electronic collars need to be very snug to work properly. They must be just tight enough allow “prongs”...
PARTS & FUNCTIONS - COLLAR Collar Receiver TURNING ON AND OFF Turning the Unit On: Press and hold the On/Off button on the Collar Receiver. The Red LED Indicator will light solidly for two seconds. Continue holding the Button until the Red light goes off. The unit is now On.
Page 10
PARTS & FUNCTIONS CONT. Intensity Selection Dial The intensity selection dial allows you to choose between sixteen different levels stimulation, allowing for very precise control. TRAINING INTENSITY LEVEL The first and most important step in training your dog with your EZT Training System is determining the correct Intensity Level to provide the proper training stimulation without over-shocking your dog.
Page 11
PARTS & FUNCTIONS CONT. Transmitter Indicator Light When one of the push button switches on the transmitter are pushed, the RED light will turn on to indicate that the transmitter is being operated. When the battery needs charging the RED light will blink once every 1/2 second while pushing a button.
Page 12
PARTS & FUNCTIONS CONT. Battery Charging Receptacles The battery charging receptacle is located on the side of the Transmitter, and on the side of the Collar Receiver facing the dog’s neck. After charging, always close the jack with the rubber plug to prevent foreign particles from getting inside the unit.
BATTERIES All EZT plus Super Trainer collars are equipped with rechargeable Nickel Metal Hydride (NiMH) batteries. NiMH batteries are not memory sensitive and do not require depletion before recharging. The batteries come partially charged from the factory. However, it is recommended that you give the battery a full charge (about 12 hours) before the first use.
TESTING Before testing, make sure that both units are fully charged and the power to the Collar Receiver is “ON”. To Test the Electronic Stimulation: A) Place the tester firmly on the electrodes of the Collar Receiver. B) Set the intensity (note - an intensity level setting of 4 or less might not be enough to light the tester).
IMPORTANT SAFETY NOTES • Before beginning training your dog should be examined by a veterinarian to assure that your dog is in good health. • Never leave your dog unattended with the unit on. Since no electronic device is perfect, there is a very slight possibility that your dog may receive an unintentional electric stimulation.
MAINTENANCE • It is very important to periodically clean your EZT plus Super Trainer for maximum performance. Regular cleaning will also lengthen the life of your unit. • Clean the EZT plus Super Trainer collar box with lukewarm water and a mild anti-bacterial soap. •...
WARRANTY D.T. Systems Premium Lifetime Warranty is the best warranty offered in the industry. This warranty is free to participating U.S. customers. (The warranty registration card must be returned within 30 days of original purchase). This changes our normal one year parts and labor warranty to a lifetime warranty against manufacturing defects on parts and a one year warranty on labor.
WARRANTY CONT. How the Limited Lifetime Warranty works: • To qualify for the Warranty you must fill out the warranty registration card which came with your system and mail it (with your original sales receipt) to D.T. Systems within 30 days of purchase. •...