Related Manuals for D.T.Systems H2O 1810 PLUS
Summary of Contents for D.T.Systems H2O 1810 PLUS
- Page 1 PLUS O 1800 Series with SmartLED Owner’s Manual • H O 1810 PLUS • H O 1820 PLUS • H O 1830 PLUS • H O 1850 PLUS...
- Page 2 NOTICE! According to how you use your transmitter, the transmitting range might be much different. You will have more range if you use your transmitter apart from your body as follows: Maximum Typical Range Minimum Range...
-
Page 3: Table Of Contents
TABLE OF CONTENTS • Table of Contents ........3 • Introduction ..........4 • Package Contents ........5 • Model Features .......... 5 • Parts & Functions ........6 • SmartLED........... 11 • Charging the Batteries........ 12 • Turning ON and OFF........13 •... -
Page 4: Introduction
INTRODUCTION Congratulations and thank you for purchasing our H PLUS Series Remote Training Collar with “Add-On” capability, the perfect remote trainer for hunting, basic obedience, and professional training. The collar’s Maxx-Range™ Internal Antenna System, industry’s only internally woven antenna in the collar, gives this unit up to a one mile range. -
Page 5: Package Contents
PACKAGE CONTENTS • Transmitter with Antenna and Lanyard • Collar Receiver • Rechargeable NiMH Batteries for both the Collar and Transmitter (already installed) • Battery Charger • Splitter Cable for simultaneous charging • Test Light • Owner’s and Training Manuals •... -
Page 6: Parts & Functions
PARTS & FUNCTIONS *The H O 1810 PLUS will not have the #1 or #2 buttons. O 1820 PLUS Button #1 - Vibration Button #2 - Vibration + Stimulation O 1830 PLUS Button #1 - Jump Stimulation Button #2 - Rise Stimulation O 1850 PLUS Button #1 - Locate Antenna... - Page 7 PARTS & FUNCTIONS Intensity Selection Dial - The intensity selection dial can be set from level 1 to level 16 to find the exact stimulation level for your dog (see page 18). Transmitter Indicator Light - When pressing any of the Transmitter buttons, the SmartLED lights green if there is 51% to 100% charge remaining, lights red if there is 21% to 50% charge remaining, or flashes...
- Page 8 PARTS & FUNCTIONS Buttons #1 & #2 (H O 1830 PLUS only) - Pressing the Jump Button (#1) makes the collar give a ‘Jump’ Stimulation, making the intensity level instantly “jump” to a user-programmed intensity level (see page 19). Pressing the Rise Button (#2) makes the collar give a stimulation that gradually increases in intensity level the longer the Rise Button is pressed.
-
Page 9: Collar Receiver
PARTS & FUNCTIONS O 1850 PLUS only. All other models will not have Beeper Horn or Beeper Wire. Collar Belt with MAXX-Range™ Beeper Wire* Beeper Horn* Antenna Contacts SmartLED Indicator Light Charging Receptacle ON/OFF Button Collar Receiver ON/OFF Button - Turns the Collar Receiver unit ON and OFF (see page 13). - Page 10 PARTS & FUNCTIONS Beeper Horn (H O 1850 PLUS only) - The Beeper Horn is attached to the collar belt. It will emit a loud tone audible from up to 450 yards away. Beeper Wire (H O 1850 PLUS only) - The Beeper Wire provides power and communication from the Collar Receiver Unit to the Beeper Horn.
-
Page 11: Smartled
SmartLED O 1800 PLUS Series units are equipped with the SmartLED battery status system. The SmartLED system lets you know when the unit is charging and when the charging is complete. It also gives you a status on how much charge is remaining in the battery during use, when it needs charging, and when the batteries will need to be replaced. -
Page 12: Charging The Batteries
CHARGING THE BATTERIES All H O PLUS Series units are equipped with rechargeable Nickel Metal Hydride (NiMH) batteries, which are not memory sensitive and do not require depletion before recharging. Although batteries come partially charged from the factory, it is recommended that they are given a full charge (about 12 hours) before initial use. -
Page 13: Turning On And Off
TURNING ON AND OFF The Transmitter is always in a permanent sleep state. It is only ON when a button is being pressed and does not need to be turned off by the user. Turning the Collar Unit ON: Press and hold the ON/OFF button. The SmartLED Indicator will light solid red for one second. -
Page 14: Testing
TESTING NOTE: Before testing, make sure that both units are fully charged and the power to the Collar Receiver is “ON”. To Test the Electronic Stimulation: A) Place the tester firmly on the contacts of the Collar Receiver. B) Set the intensity (note - an intensity level setting of 4 or less might not be enough to light the tester). - Page 15 TESTING To Test the Rise: O 1830 PLUS only) A) The Rise feature will gradually increase the inten- sity level starting from the level set on your dial. To see a greater range of intensity change, set the intensity dial to a lower level. B) Press and hold the button on the right side of the transmitter (Rise button) and the test light will get brighter as the button is held.
-
Page 16: Programming The Collar
PROGRAMMING THE COLLAR When adding an “Add-On” collar, the collar will need to be programmed to the transmitter. If your current collar unit is not responding to the transmitter, it may also need to be reprogrammed to the transmitter. 1. Select the desired Collar Selecting Switch position on the transmitter. -
Page 17: Properly Fitting The Collar
PROPERLY FITTING THE COLLAR NOTE: Proper collar tightness and position are very important to insure safe and consistent collar use. All electronic collars need to be very snug around the dog’s neck to work properly. They must be just tight enough to allow the “contacts”... -
Page 18: Setting The Intensity Level
SETTING THE INTENSITY LEVEL It is very important to set the correct intensity level on your H O PLUS Training System before beginning your training sessions to provide the proper level of stimulation without over-stimulating your dog. To do this, place the Intensity Selection dial so that the system is set on Level 1. - Page 19 SETTING THE INTENSITY LEVEL Jump stimulation is a great feature when regularly us- ing two different stimulation levels in training. It is also a great safety tool for emergency situations when your dog is excited and cannot feel or ignores the normal intensity level.
-
Page 20: Maintenance
MAINTENANCE It is very important to periodically clean your H PLUS Series systems for maximum performance. Regular cleaning will also lengthen the life of your unit. • Clean the collar box, belt and buckle with lukewarm water and a mild anti-bacterial soap. •... -
Page 21: Important Safety Notes
IMPORTANT SAFETY NOTES • Before training with this unit, your dog’s health should be examined by a veterinarian. • Do not use with aggressive-tempered dogs. • Your H O PLUS Series collar is a very valuable tool if used correctly. It is extremely important that you completely understand all the functions of the collar and how to properly train with it before placing it on your dog. -
Page 22: Warranty
WARRANTY • D.T. Systems Premium Lifetime Warranty is the best warranty offered in the industry. This warranty is free to participating U.S. customers (a completed warranty registration card must be returned within 30 days of original purchase). This changes our normal one year parts and labor warranty to a limited lifetime warranty against manufacturing defects on parts and a one year warranty on labor. -
Page 23: Fcc/Ic/Ce Compliance
FCC/IC/CE COMPLIANCE Your H O 1800 PLUS Series Trainer has been manufactured under complete compliance with Part 15 of the Federal Communication Commission (FCC) rules, Industry Canada (IC) Standard RSS-310, and Article 3 of the Directive 1999/5/EC. The complex internal structure of each product has been designed to operate within specific regulations of FCC specifications. -
Page 24: Contact Information
2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (214) 350-9446, (888) 588-8364 Fax: (214) 350-7847 Website: www.dtsystems.com E-mail: customerservice@dtsystems.com O PLUS 2012.04.12 Printed in Korea...