D.T.Systems SUPER TRAINER EDT 100 Owner's Manual

D.T.Systems SUPER TRAINER EDT 100 Owner's Manual

Edt series electronic dog trainer

Advertisement

TM
TM
SUPER TRAINER
SUPER TRAINER
EDT SERIES
Electronic Dog Trainer
Owner's Manual
• EDT 100
• EDT 102
• EDT 200
• EDT 202
• EDT 300
• EDT 302
D.T. SYSTEMS, INC.

Advertisement

Table of Contents
loading

Summary of Contents for D.T.Systems SUPER TRAINER EDT 100

  • Page 1 SUPER TRAINER SUPER TRAINER EDT SERIES Electronic Dog Trainer Owner’s Manual • EDT 100 • EDT 102 • EDT 200 • EDT 202 • EDT 300 • EDT 302 D.T. SYSTEMS, INC.
  • Page 2: Introduction

    Congratulations and Thank you for purchasing our EDT Super Trainer training collar. The EDT series collars satisfy all your dog training needs. With up to a 1,200 yard range they are perfect for hunting, basic obedience and professional training. EDT series collars feature twenty levels of stimulation intensity, adjustable right from the handheld transmitter.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS • Introduction ..........2 • Table of Contents..........3 • Features............4 • Package Contents..........4 • Individual Model Features......5 • Parts and Functions........7 • Adjusting and Positioning Your Collar for Proper Fit ......11 • Batteries ............12 • Testing ............14 • Important Safety Notes .........15 •...
  • Page 4: Features

    FEATURES Every EDT Super Trainer Electronic Dog Training System Features: • Digital Technology • 1,200 Yard Range—(Over 2/3 mile) • Lightweight, Compact Collars (6.7 oz.) and Transmitters (5.7 oz.) • 20 Adjustable Intensity Levels (right from the Transmitter) • Invisible, Embedded Collar Antenna •...
  • Page 5: Individual Model Features

    INDIVIDUAL MODEL FEATURES EDT 100 and EDT 102 • The EDT 100 features the options of Momentary (Nick) Stimulation, and Constant Stimulation. • The EDT 102 has the same features as the EDT 100 and comes with two Collar Receiver units which are operated from the same transmitter.
  • Page 6 INDIVIDUAL MODEL FEATURES CONT. EDT 300 and EDT 302 • The EDT 300 features the options of Constant Stimulation and Positive Vibration. • The EDT 302 has the same features as the EDT 300 and comes with two Collar Receiver units which are operated from the same transmitter.
  • Page 7: Parts And Functions

    PARTS & FUNCTIONS EDT 200 SHOWN Transmitter Parts & Functions Transmitter Indicator Light When one of the push button switches on the transmitter are pushed, the RED light will turn on to indicate that the transmitter is being operated. When the battery needs charging the RED light will blink once every 1/2 second.
  • Page 8 PARTS & FUNCTIONS CONT. Intensity Selection Dial The intensity selection dial allows you to choose between twenty different levels of stimulation, allowing for very precise control. Stimulation Activation Push Buttons Pressing the upper button causes the collar to administer a Momentary Stimulation or “Nick”.
  • Page 9 PARTS & FUNCTIONS CONT. Transmitter Antenna Be very careful when screwing the 2” antenna into the transmitter. Hand tighten only. Over tightening could cause damage to the antenna or the antenna mount. Battery Charging Jack - Transmitter The battery charging jack is located on the side of the transmitter.
  • Page 10 PARTS & FUNCTIONS CONT. Indicator Light When the ON/OFF button on the Collar Receiver is pushed, the RED light will flash steadily once every two seconds to indicate that the unit is active. The RED light changes to a rapid flash (twice per second) when the battery is low and in need of charging.
  • Page 11: Your Collar For Proper Fit

    PARTS & FUNCTIONS CONT. Collar Belt with Imbedded Receiver Antenna The imbedded collar antenna ends at the displaced hole midway along the belt. CAUTION Do not cut the collar belt. Doing so will damage the antenna and may result in severely decreased receiver range.
  • Page 12: Batteries

    ADJUSTING & POSITIONING YOUR COLLAR FOR PROPER FIT CONT. • All electronic collars need to be very snug to work properly. They must be just tight enough to allow the “prongs” or electrodes to make good skin contact. • If your collar is too loose, the stimulation may not work properly because good skin contact is not being achieved.
  • Page 13 BATTERIES CONT. The batteries come partially charged from the factory. It is, however, recommended that you give the battery a full charge before the first use. This takes about 14 hours. Remember - Always keep batteries away from flammable substances (especially when charging). When storing the unit for long periods remember to regularly give the batteries a full charge (14 hours).
  • Page 14: Testing

    TESTING There are three methods you can use to test your EDT Super Trainer First, you should make sure that both units are fully charged. Then turn on the power to the collar receiver. Next, follow one of these three steps: To Test the Electronic Stimulation: A)Place the tester firmly on...
  • Page 15: Important Safety Notes

    TESTING CONT. To Test the Vibration (with the Tester): A)Follow the directions on page 14, but set the stimulation mode slide selector to “V” or “SV”. B)The unit should vibrate and the tester should light. To Test the Vibration (without the Tester): A)Follow the directions above.
  • Page 16: Maintenance

    IMPORTANT SAFETY NOTES CONT. • The electrodes on this collar are made with high grade stainless steel to help prevent any chemical or allergic reactions with your dog’s skin. • To prevent neck irritation, the collar should never be worn for more than 12 hours a day. Daily changing the collar location on the dog’s neck will also help prevent irritations.
  • Page 17: Warranty

    WARRANTY D.T. Systems Premium Lifetime Warranty is the best warranty offered in the industry. This warranty is free to participating U.S. customers. (The warranty registration card must be returned within 30 days of original purchase). This changes our normal one year parts and labor warranty to a lifetime warranty against manufacturing defects on parts and a one year warranty on labor.
  • Page 18: Fcc Compliance

    To qualify for the Warranty you must fill out the warranty registration card which came with your system and mail it (with your original sales receipt) to D.T. Systems within 30 days of purchase. • There is no charge for parts or labor for the first year on any of our lifetime warranted products.
  • Page 20 D.T. Systems, Inc. 2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (214) 350-9446, (888) LUV-U-DOG Fax: (214) 350-7847 Website: http://www.dtsystems.com E-mail: customerservice@dtsystems.com...

Table of Contents