Related Manuals for D.T.Systems SPT 2420
Summary of Contents for D.T.Systems SPT 2420
- Page 1 SPT SERIES Electronic Dog Trainer Owner’s Manual • SPT 2420 • SPT 2422 • SPT 2430 • SPT 2432...
-
Page 3: Introduction
Congratulations and thank you for purchasing one of dog training systems. The SPT series represents the absolute latest techno- logical advancement in the Electronic Dog Training World. They offer compact, lightweight collar receivers which include completely internal antenna systems. The convenient, one-touch Digital Transmitters are lightweight and feature an LCD dis- play which allows for extreme ease of use. -
Page 4: Table Of Contents
TABLE OF CONTENTS • Introduction ......3 • Table of Contents ......4 •... -
Page 5: Features
IMPORTANT NOTE Please read this owner’s manual in its entirety before attempting to operate this unit. Should you have any questions about our collars or their operation please contact our Customer Service Department (see last page for contact information). FEATURES Every Electronic Dog Training System Features:... -
Page 6: Individual Model Features
Continuous Stimulation, Jump Stimulation (patent pend- ing), Rise Stimulation (patent pending) and Positive Vibration. • The SPT 2422 has the same features as the SPT 2420 and comes with two Collar Receiver units (orange and black) which are operated from the same transmitter. -
Page 7: Adjusting And Positioning Your Collar For Proper Fit
ADJUSTING & POSITIONING YOUR COLLAR FOR PROPER FIT Proper collar tightness and position are very important to insure safety and correct functioning every time you use the collar. • All electronic collars need to be very snug to work properly. They must be just tight enough to allow the “prongs”... -
Page 8: Parts And Functions
PARTS & FUNCTIONS Transmitter (SPT 2430 shown, models may vary slightly) - Page 9 PARTS & FUNCTIONS CONT. Collar Receiver (SPT 2430 model shown) LCD Display Indicators...
-
Page 10: Turning On And Off
TURNING YOUR UNIT ON & OFF Turning the Unit On: Press and hold the Power button on the Collar Receiver. The red LED Indicator will light solid for two seconds. Continue holding the button until the red LED light goes off. The unit is now ON. The LED indicator will now flash approximately every 2 seconds. -
Page 11: Intensity Levels
INTENSITY LEVEL The first and most important step in training your dog with your SPT Training System is the determination of the cor- rect Intensity Level to provide the proper training stimula- tion without over stimulating your dog. To do this, place the collar ON and place it on the dog’s neck. - Page 12 INTENSITY LEVEL (CONT.) Using the Rise Stimulation The Rise function will gradually increase stimulation from your current intensity level to the maximum intensity level (level 50) while the “RISE” button is being pressed. The intensity level will return to its original setting when the button is released.
-
Page 13: Remote Training Buttons
Your SPT 2400 series collar has four control buttons on the front of the transmitter and up to three buttons on the left side of the transmitter (1 button on SPT 2420 and 2422 models, 3 buttons on SPT 2430 and 2432 models). -
Page 14: Switching Between Collars (Two Dog)
SWITCHING BETWEEN COLLARS (TWO DOG MODELS) With SPT Two Dog Systems (2422 & 2432) you can control two dogs with one transmitter. The LCD display shows whether you are currently controlling the Orange Collar Receiver (ORG) or the Black Collar Receiver (BLK). To switch the currently active col- lar, simply press the Collar Selection button (marked “O/B”). -
Page 15: Batteries
BATTERIES • All training collars are equipped with rechargeable Nickel-Metal Hydride (NiMH) batteries which are not memory sensitive and do not require depletion before recharging. • When the battery is running low in the transmitter, the back- light will blink 3 times every second to alert you of this status. •... -
Page 16: Testing
TESTING There are two or three methods you can use to test your depending upon your model’s features. First, you should make sure that both the transmitter and receiver are fully charged. Then, turn on the power to the Collar Receiver. Next, follow one of these three steps: To Test the Electronic Stimulation: A) Place the tester firmly on... - Page 17 TESTING To Test the Vibration: A) Press the VIBRATION button (bottom button on left side of transmitter). B) When you press the VIBRATION button the unit should vibrate but the tester should not light. To Test the Beeper: (SPT 2430 and 2432 only) A) Press the LOCATE button (top button on left side of transmitter).
-
Page 18: Programming The Collar
PROGRAMMING THE COLLAR Press and hold the Power button on the Collar Receiver. You will see the LED light on the collar blink 7 times before staying solid. You must hold down the power button until the LED light becomes solid. Simultaneously press and release the “NICK”... -
Page 19: Important Safety Notes
IMPORTANT SAFETY NOTES • Before beginning training your dog should be examined by a veterinarian to assure that there are no physical reasons for your dog’s excessive barking and to assure that your dog in good health. • Your is a very valuable tool if used correctly. -
Page 20: Warranty
WARRANTY D.T. Systems Premium Lifetime Warranty is the best war- ranty offered in the industry. This warranty is free to par- ticipating U.S. customers. (The warranty registration card must be returned within 30 days of original purchase). This changes our normal one year parts and labor warranty to a lifetime warranty against manufacturing defects on parts and a one year warranty on labor. - Page 21 WARRANTY (CONT.) How the Limited Lifetime Warranty works: - To qualify for the Warranty you must fill out the warranty registration card which came with your system and mail it (with your original sales receipt) to D.T. Systems within 30 days of purchase.
-
Page 22: Fcc Compliance
FCC COMPLIANCE Your has been manu- factured under complete compliance with the Federal Communication Commission (FCC). The complex internal structure of each product has been designed to operate with- in specific regulations of FCC specifications. Any unautho- rized modifications to your product is a violation of these specifications. -
Page 24: Contact Information
2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (214) 350-9446, (888) LUV-U-DOG Fax: (214) 350-7847 Website: http://www.dtsystems.com E-mail: customerservice@dtsystems.com...