Page 1
All Surface Cleaner Model No.: Operator Manual 613627 613792 Rev. 00 (08 02) Home Find... Go To..
Page 2
ENGLISH This manual is furnished with each new 750 model. It provides necessary operation, maintenance MACHINE DATA instructions and an illustrated parts list. Read this manual completely and understand the machine before operating or servicing. Please fill out at time of installation for future reference.
FOR SAFETY: 1. Do not operate machine: – Unless trained and authorized. – Unless operator manual is read and understood. – In flammable or explosive areas. – Unless safety goggles are worn. 750 (08–02) Home Find... Go To..
Power Cord Before Servicing Machine If the supply cord is damaged or broken, it must be replaced by the manufacturer or it’s service agent or a similarly qualified person in order to avoid a hazard. 750 (08–02) Home Find... Go To..
(Figure 3). water-resistant surfaces. To order the “Formula 710 Multi-Surface Acid Cleaner” or an approved substitute, contact your Tennant supplier. ATTENTION: Use of unapproved or inappropriate chemicals may cause damage to machine and surfaces and could void your warranty...
If the supply cord is damaged or broken, it must be replaced by the manufacturer or it’s service agent or a similarly qualified person in order to avoid a hazard. FOR SAFETY: Do not operate machine with the use of an extension cord. 750 (08–02) Home Find... Go To..
2. Remove trash containers from room. FIG. 9 3. Remove exposed paper products from room. 4. Dust clean overhead fixtures and vents. The machine is also designed for dust cleaning (See OTHER CLEANING USES WITH MACHINE). 750 (08–02) Home Find... Go To..
Page 10
(O) position and rinse the gun of cleaning agent. 7. While the cleaning solution is working, use the brush tool to scrub corners, cove base and heavily soiled areas (Figure 14). FIG. 12 FIG. 14 750 (08–02) Home Find... Go To..
FIG. 23 6. Press the vacuum/blower switch towards the vacuum symbol (Figure 24). FIG. 20 3. Press the vacuum/blower switch towards the blower symbol to activate the blower (Figure 21). FIG. 24 FIG. 21 750 (08–02) Home Find... Go To..
11. Push the machine to the drain sit and empty the recovery tank. NOTE: After cleaning one area, it is best to empty the recovery tank before proceeding to the next area to be cleaned. 750 (08–02) Home Find... Go To..
2. Press the vacuum/blower switch towards the vacuum symbol. 3. Extract the remaining rinse solution from the solution tank and flush out the tank with clean water (Figure 30). 750 (08–02) Home Find... Go To..
Squeeze the (Figure 33). trigger for five seconds after turning switches off. 7. Perform the recommended maintenance procedures (See MACHINE MAINTENANCE). FIG. 33 750 (08–02) Home Find... Go To..
(Figure 37). FIG. 40 4. Empty any leftover water from the solution tank if storing machine for an extended period or if transporting the machine (See DRAINING FIG. 37 TANKS). 750 (08–02) Home Find... Go To..
3. Unlatch the two latches at the front of the machine and carefully hinge the machine open (Figure 45). FIG. 45 4. When closing the machine, make sure the hoses are not pinched or kinked. 750 (08–02) Home Find... Go To..
No air–flow from blower hose. Loose blower hose connection. Secure hose connection. Defective blower motor. Contact Service Center. Worn carbon brushes in blower motor. Contact Service Center. 750 (08–02) Home Find... Go To..
ENGLISH SPECIFICATIONS Model TENNANT 750 LENGTH 927 mm WIDTH 470 mm HEIGHT 953 mm WEIGHT 57 Kg / 64 Kg with accessories SOLUTION TANK CAPACITY 157 L RECOVERY TANK CAPACITY 72 L SOLUTION PUMP 230V, rated 500 psi, 3.7 A PUMP FLOW RATES (MAX) High Pressure: 1 gal (3.8 L) per min.