Related Manuals for Miele PG 8050i
Summary of Contents for Miele PG 8050i
-
Page 1: Installation Instructions
Installation instructions Professional dishwasher PG 8050i en - CA, US To prevent accidents and machine damage, read these instructions before installation or use. M.-Nr. 07 865 040... - Page 2 Always read the "Warning and safety instructions" in the operations manual before installing the dishwasher.
-
Page 3: Table Of Contents
Contents Installation ............4 1. -
Page 4: Installation
Installation Integrated ("i") dishwashers To ensure stability, these "i" models are designed for installation dishwashers should only be installed under a continuous countertop. under a continuous countertop and – The control panel with accessories is securely fastened to the cabinet enclosed in a separate package for base units. - Page 5 Installation Dimensions Dishwasher model PG 8050i 1) with 34 7/8" (870 mm) machine height 2) with 32 1/4" (820 mm) machine height Range of adjustment is approximately 2" (5 cm). Machine heights between 35" and 37" can be obtained if the supplied legs are removed and extended legs are attached.
-
Page 6: Installing The Steam Deflector (If Applicable)
Installation 1. Installing the steam deflector (if applicable) A stainless steel coverplate is supplied to protect the underside of the countertop against steam rising from the dishwasher when the door is opened. If the countertop is made of Corian(r), granite, marble or other solid, waterproof material, the steam deflector should not be used. -
Page 7: Installing The Dishwasher Under The Countertop
Installation 2. Installing the dishwasher Installing the slides under the countertop Two slides are included and should be installed on the feet of the dishwasher For ease of service and quick before the machine is pushed under disconnection, it is best to install the the countertop. -
Page 8: Mounting Brackets
Installation Mounting brackets The drain hose connection at the rear of the dishwasher can be turned to allow To ensure stability this dishwasher the hose to be angled to the right or should be securely attached to the left. countertop (step 6). Two mounting brackets are included for this purpose. -
Page 9: Leveling Legs
Installation Leveling legs ^ Adjust the front leveling legs by pushing on the feet with a slotted ^ Adjust the rear leveling legs to the screwdriver. required height with a T20 Torx screwdriver. The dishwasher should be raised To raise the machine - turn clockwise. until it just touches the underside of To lower the machine -turn counter the countertop. -
Page 10: Aligning The Control Panel With The Drawer Fronts
Installation 3. Aligning the control panel If necessary, individual (or all) spacer bars can be removed. with the drawer fronts ^ The control panel can be aligned with the drawer fronts of the kitchen cabinets by adjusting the spacer bars. ^ To remove the spacer bars from the control panel, place the panel on a table, printed side up, and gently... -
Page 11: Fitting The Front Panel
Installation 4. Fitting the front panel Fitting the mounting bracket Mounting brackets are already fitted on A mounting bracket must be fitted to stainless steel door fronts. These fronts the rear of the front panel. cannot be shortened. (Go to "Fitting Templates are provided to position the and securing the door front".) mounting bracket and the front panel... - Page 12 Installation ^ Hang the bracket on the machine ^ Slide the mounting bracket up or door. down until the oblong holes on the machine door align with the ^ Slide the top edge of the templates corresponding marks on the template under the spacer bars and control (as shown in the left side of inset a panel.
- Page 13 Installation ^ Remove the bracket from the machine door and place it on the rear of the door panel so that: – the bracket is centered left to right, – the bottom of the bracket is aligned with the (X) line. ^ Tape the bracket to the door panel to hold it in place while the mounting holes are being drilled.
- Page 14 Installation ^ Push up one side of the door panel until it touches the spacer bars (or control panel if spacer bars are not being used) and lightly tighten the T20 Torx screws on the corresponding edge of the machine door.
-
Page 15: Securing The Dishwasher To The Countertop
Do not drill any additional holes through any portion of the wash cabinet. If in doubt on how to secure the dishwasher, please call the Miele Technical Service Department. -
Page 16: Adjusting The Door Springs
^ To adjust the door springs use a T20 then stronger springs should be fitted. Torx or a small slotted screwdriver Please contact your Miele dealer or the and turn the screw: Miele Service Department for advice. - clockwise to increase the tension - counterclockwise to decrease the tension. -
Page 17: Installing The Toekick
Installation ^ Place the toekick board directly in 7. Installing the toekick front of the kitchen cabinet base run, The base area of the dishwasher is but do not attach. normally covered with the toekick board ^ Carefully open the dishwasher door. of the kitchen cabinets. - Page 20 Alteration rights reserved / Publication date: 08/24/2010 M.-Nr. 07 865 040 / 01...