Table of Contents
Advertisement
c
o
m
m
u
n
A General System Tamper Reporting Code will be transmitted when the tamper zone on any module is violated.
The General System Tamper Restoral Reporting Code will be transmitted when the tamper zone on the module
is restored.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Tamper Reporting Codes ............................................................... Section [330]
Tamper Restoral Reporting Codes ................................................ Section [334]
General System Tamper and Restoral ........................................... Section [338]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Priority/Emergency
The panel will transmit a Keypad Fire Alarm Reporting Code and the Keypad Fire Restoral Reporting Code
when the Fire Key on any wireless key is pressed for two seconds.
The panel will transmit a Keypad Auxiliary Alarm Reporting Code and the Keypad Auxiliary Restoral
Reporting Code when the Auxiliary Key on any wireless key is pressed for two seconds.
The panel will transmit a Keypad Panic Alarm Reporting Code and the Keypad Panic Restoral Reporting Code
when the Panic Key on any wireless key is pressed for two seconds.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Priority Alarm and Restoral Reporting Codes ............................... Section [329]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Maintenance
The panel will transmit a Battery Trouble Alarm Reporting Code when the backup battery charge drops
below 5.75 V
. The Battery Trouble Restoral Reporting Code will not be transmitted until the battery has
DC
been charged to over 6.0 V
To prevent the panel from transmitting an AC Failure Trouble Alarm Reporting Code during short power outages,
the panel will not send the signal unless AC power is lost for the amount of minutes programmed for the AC Failure
Communication Delay. The AC Failure Trouble Restoral Reporting Code follows the AC failure communication
delay as well.
If AC Failure Communications Delay is programmed as "000," then the AC failure transmission will
be disabled.
A Fire Trouble Alarm Reporting Code will be immediately transmitted when an open condition is measured on
any Fire type zone (see Section 5.2 – "Zone Definitions"). The Fire Trouble Restoral Reporting Code will be
transmitted as soon as the problem is corrected.
The TLM Restoral Reporting Code will be transmitted within 10 seconds after a telephone line monitoring
problem is corrected.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Maintenance Alarm Reporting Codes ............................................ Section [349]
Maintenance Restoral Reporting Codes ........................................ Section [350]
AC Failure Communication Delay .................................................. Section [370]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Test Transmissions
The panel can be programmed to transmit a Periodic Test Transmission Reporting Code (see Section 6.4 –
"Test Transmissions"), and a System Test Reporting Code when the end user performs a system test.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Test Transmission Reporting Codes .............................................. Section [352]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Wireless Maintenance
The panel will transmit a General Zone Low Battery Alarm reporting code if a low battery condition is
indicated by a detector. The transmission of the trouble will be delayed by the number of days programmed
for Zone Low Battery Transmission Delay. The General Zone Low Battery Restoral Reporting Code will be
transmitted when the problem is corrected. The specific zone that caused the trouble will be recorded in the
event buffer.
The restoral will not be transmitted until all detectors indicate good battery conditions.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Wireless Maintenance Reporting Codes ....................................... Section [353]
Zone Low Battery Transmission Delay ........................................... Section [370]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
i
c
a
t
i
o
.
DC
n
s
p
r
o
8
g
r
a
m
m
i
n
g
Advertisement
Table of Contents
